Songmics Vanity Table Assembly Instructions

Introduction

Please read these assembly and safety instructions carefully before using the vanity table for the first time. Keep this manual for future reference. This manual applies to all types of Songmics vanity tables. While every effort has been made to ensure accuracy and completeness, not all variations or assembly methods can be described. If you require further information or encounter problems not covered, please contact the seller. Reproduction or translation without written permission from Songmics International GmbH is prohibited.

Safety Instructions

Warnings:

• The vanity table can tip over, causing serious or fatal injury. Ensure it is securely anchored to the wall using the provided anti-tip kit. The type of fixing device depends on your wall material.
• Do not use the product if any parts are damaged or missing.
• This product is not intended for children. Adult supervision is required. Do not allow children to climb on or play with the vanity table to prevent tipping or mirror breakage.
• Keep children away from the assembly area during setup, as small parts (screws, etc.) can be a choking hazard if swallowed or inhaled.
• Keep packaging materials (plastic bags, styrofoam, etc.) away from children to prevent suffocation hazards.

General Notes

• The product is intended for indoor, personal use only, not for commercial or outdoor use. The seller is not liable for damages caused by incorrect assembly or improper use.
• To prevent tipping, the furniture must be fixed to the wall with the safety fitting provided. Ensure you use appropriate wall anchors for your specific wall type.
• Before assembly, check that the product is intact and all components are present. Do not place unpacked parts directly on the floor to avoid scratches.
• Assembly is recommended by two adults. Assemble on a flat, clean, and soft surface (e.g., the packaging carton) to prevent damage.
• Follow the illustrated steps for part alignment and adjustment, then gradually tighten all screws. Hand screwdrivers are recommended; electric drills may damage the product.
• After assembly, place the vanity table in a ventilated area for a few days to dissipate any new odor.
• Periodically check that all screws and connections are tight. Retighten if necessary.
• Avoid contact with sharp objects or corrosive chemicals, which can damage the surface.
• Protect surfaces from heat and liquids using mats and coasters. Wipe up spills immediately. Use a desk mat when writing.
• Avoid exposure to direct sunlight, rain, or humid environments, which can cause distortion, cracking, or discoloration.
• Do not store heavy objects in drawers, as this can cause deformation or paint flaking. Do not shake or strike the table after assembly.
• Seek assistance when moving the furniture. Lift the table; do not drag it, as this can cause damage or injury.
• For moving to a new location, it is recommended to disassemble the product completely to avoid injury or damage. Retain all fittings.
• For daily cleaning, use a soft, damp cloth, with a mild detergent if necessary, and then dry with a soft cloth.

Parts List

A diagrammatic representation of all parts is provided in the original document. The following table lists the components:

Assembly Steps

The following steps detail the assembly process. Refer to the diagrams in the original document for visual guidance.

1. Step 1: Attach the side legs (D) to the base unit (C). Use eight screws (A1) and eight washers (B1). Ensure parts are aligned before tightening.
2. Step 2: Assemble the drawers. Attach the drawer front panels (G) to the drawer side panels (E). Use six screws (A3). Then insert the assembled drawer units (J).
3. Step 3: Connect the mirror support pillars (I) to the top shelf unit (F). Use four screws (A2) and four washers (B2).
4. Step 4: Attach the mirror (H) to the assembled support pillars (I). Use two screws (A4).
5. Step 5: Attach the decorative leg supports (K) to the main legs (D). Use eight screws (A1) and eight washers (B1).
6. Step 6: Assemble the stool. Attach the stool seat (L) to its legs (implied parts). Place the assembled vanity and stool in their desired location.