GRÅVACKA Cord Set Assembly Instructions
Brand: IKEA
Important Safety Information
English: Always shut off power to the circuit before starting installation work. In some countries, electrical installation work may only be carried out by an authorized electrical contractor. Contact your local electricity authority for advice.
Español: Desconecta siempre el interruptor general de la electricidad antes de iniciar cualquier trabajo de instalación. En algunos países, la instalación eléctrica sólo puede realizarla un electricista profesional. Ponte en contacto con las autoridades locales para saber cuál es tu caso.
Português: Desligue sempre a corrente elétrica antes de começar um trabalho de instalação. Em alguns países os trabalhos de instalação eléctrica só podem ser realizados por um electricista autorizado. Contacte a sua autoridade local de electricidade para aconselhamento.
中文: 安装工作开始前,请务必切断电路电源。在一些国家,电气安装必须由有资质的电力承包商完成。请联系您当地的电力部门,征询建议。
繁中: 安裝前請務必關掉電源。有些國家的電力安裝工作需由有執照的專業電工執行,如有任何疑問,請聯絡專業人員。
한국어: 설치작업을 시작하기 전 반드시 회로의 전원을 차단하세요. 일부 국가에서는 공인전기시공업체만 전기 공사를 진행할 수 있습니다. 관련 정보는 지역 전력 관할 기관에 문의하세요.
日本語: 設置作業を開始する前に必ずブレーカーを切ってください。電気工事の作業を行うには、資格を必要とする国もあります。お近くの電気工事店にご相談ください。
Bahasa Indonesia: Selalu matikan listrik ke sirkuit sebelum memulai pekerjaan pemasangan. Di beberapa negara pekerjaan pemasangan listrik hanya boleh dilakukan oleh tukang listrik tersertifikasi. Hubungi tukang listrik berwenang di tempat anda untuk saran.
Bahasa Malaysia: Sentiasa padamkan bekalan kuasa ke litar sebelum memulakan kerja-kerja pemasangan. Di beberapa negara kerja-kerja pemasangan elektrik hanya boleh dilakukan oleh kontraktor elektrik yang bertauliah. Hubungi pihak berkuasa tempatan untuk mendapatkan nasihat tentang bekalan elektrik.
عربي: دائما أفصل الطاقة عن الدائرة الكهربائية قبل البدء في أعمال التركيب. في بعض الدول قد يتم تنفيذ أعمال التركيبات الكهربائية بواسطة كهربائي معتمد فقط. اتصل بالجهة المختصة في بلدك لأخذ التوجيهات.
ไทย: ในการติดตั้งอุปกรณ์ไฟฟ้าทุกครั้ง จำเป็นต้องตัดกระแสไฟฟ้าออกจากวงจรก่อน เพื่อความปลอดภัย บางประเทศกำหนดให้การติดตั้งงานไฟฟ้าต้องดำเนินการโดยช่างไฟฟ้าผู้ได้รับใบอนุญาตเท่านั้น คุณสามารถติดต่อขอรับคำแนะนำได้จากหน่วยงานไฟฟ้าท้องถิ่น
Tiếng Việt: Luôn ngắt điện trước khi bắt đầu lắp đặt. Ở một số quốc gia, việc lắp đặt điện chỉ có thể được thực hiện bởi thợ điện được cấp phép. Hãy liên hệ với đơn vị có thẩm quyền về điện tại địa phương để được tư vấn.
Parts Included
- 1x Ceiling hook assembly (Part no. 190096)
- 1x Canopy (Part no. 190905)
- 1x Cord grip (Part no. 190949, 10077185, 10077184, 10077311)
- 1x Cord grip (Part no. 190948, 190950, 10077186, 10077187, 10077309)
- 1x Wire connector (Part no. 153748, 153749)
Assembly Steps
Step 1: Prepare the Canopy
Insert the cord through the canopy.
Illustration shows a hand pulling the cord through the top of the canopy.
Step 2: Secure the Cord
Slide the cord grip onto the cord and into the canopy.
Illustration shows a cord grip being slid onto the cord and then into the canopy.
Step 3: Attach the Wire Connector
Connect the wire connector to the cord.
Illustration shows a hand holding the wire connector and attaching it to the cord.
Step 4: Route the Wires
Feed the wires through the wire connector, ensuring correct polarity (L for Line, N for Neutral).
Illustration shows wires being fed through the connector with close-ups indicating the L and N connections.
Step 5: Secure the Wires
Ensure the wires are securely held by the wire connector.
Illustration shows the wires secured within the wire connector.
Step 6: Mount the Ceiling Hook
Attach the ceiling hook assembly to the ceiling using appropriate screws (not included). Ensure the hook is oriented correctly to support the cord set.
Illustration shows the ceiling hook assembly being attached to the ceiling with screws.
Step 7: Hang the Cord Set
Hang the cord set onto the ceiling hook.
Illustration shows the cord set being hung on the ceiling hook.
Step 8: Connect the Wires
Connect the wires from the cord set to the corresponding wires in the ceiling fixture. Ensure proper connection for Line (L) and Neutral (N).
Illustration shows the wire connections being made, with close-ups detailing the L and N connections.
Step 9: Secure the Connection
Ensure the wire connections are secure. You should hear a click when the connector is properly engaged.
Illustration shows the wire connector being clicked into place.
Step 10: Adjust the Cord Length
CAUTION! Do not overtighten. Adjust the cord to the desired length by carefully tightening the cord grip.
Illustration shows a hand adjusting the cord length by turning the cord grip.
Step 11: Install the Light Bulb
Screw in the light bulb (not included) into the socket.
Illustration shows a light bulb being screwed into the socket.
