Nuvance Drone User Manual

Safety Instructions

It is illegal to use drones within 5,000 meters of a runway to ensure the safety of aviation radio stations. If the government designates certain areas, temporarily stop using model remotes. Fly only in good, windless weather and avoid extreme conditions such as heat, strong winds or rain. Choose an open area and always keep a safe distance from people, animals, and obstacles.

After launching the drone, do not make contact with the drone's rapidly rotating parts.

Do not touch the battery and motor during or after using the drone, as they can be hot. Let them cool for 30 minutes to prevent burning.

Do not look directly into the light beam of the LEDs to avoid affecting eyes.

Control Wings

1. Before your flight, check that the wings are installed correctly. Refer to the diagram below for proper placement.
2. You can easily replace the wings yourself with the provided screwdriver and screws.

[Diagram: Top-down view of the drone showing propellers labeled A and B, indicating pairs.]

Remote Control Overview

[Diagram: Detailed illustration of the remote control, showing components like the aerial, phone holder, left and right joysticks, digital screen, power switch, GPS switch, return key, and various indicator lights (Status, Headless, GPS, Charging). Labels point to each component.]

How to Use

1. Place one of the supplied batteries at the bottom of the drone until it clicks into place. Ensure the battery is fully charged with the included charging cable. A red LED light indicates the battery is charging; no LED light means it is fully charged.
2. Unfold the four wings and set the drone in a safe, open place.
3. Unfold the included remote control and ensure it is fully charged with the charging cable. Refer to the image below to prepare the remote control.

[Diagram: Series of illustrations showing the steps to unfold and prepare the remote control for use.]

Connecting to the App

1. Download the RX Drone app from the Appstore/Playstore.
2. In your phone's Wi-Fi settings, connect to the drone's network (visible when the drone is on).
3. Open the app to check the connection. Upon successful connection, the drone's name will appear in the gray box at the bottom of the app interface.

Calibrating Drone Outdoors

1. Turn on the drone and place it on a horizontal surface. Stand behind the drone so that the front faces forward.
2. Turn on the remote control.
3. Pair the remote control with the drone by pushing the left joystick up once and then down. A beep indicates that pairing is complete.
4. Press the geomagnetic calibration button (FIG. 1). When the LED light starts flashing, rotate the drone clockwise horizontally 3 times (FIG. 2) until you hear a sound. The horizontal calibration is complete.
5. Next, rotate the drone clockwise 3 times vertically (FIG. 3) until you hear a sound again. The vertical calibration is complete.
6. Place the drone horizontally on the ground and wait for the remote control to find at least 8 GPS satellites (AFB. 1). If the remote control does not find any satellites, move the drone or wait. A sound from the remote control indicates that the GPS search is complete.

[Diagram: Illustration of the remote control highlighting the geomagnetic calibration button (FIG. 1).]

[Diagram: Drone being rotated horizontally clockwise for calibration (FIG. 2).]

[Diagram: Drone being rotated vertically clockwise for calibration (FIG. 3).]

[Diagram: Image of the remote control's digital screen showing GPS status, satellite count (0 PCS), mode, battery level, and altitude/distance readings (AFB. 1).]

Preparing for Takeoff

1. Press the release button on the remote control to prepare the drone for takeoff.
2. Unlock the drone by pressing the "unlock" button (FIG 1). The four propellers will then begin to rotate evenly. Use the joysticks to slowly take off the drone. Note that the left joystick controls vertical ascent, and the right joystick controls horizontal movement.

[Diagram: Illustration highlighting the "unlock" button on the remote control (FIG. 1).]

Calibrating Drone Indoors

Calibrate the drone as described above for outdoor calibration. Then, press and hold the GPS button for a few seconds until the remote control indicates "GPS OFF." The GPS is now disabled, and the drone is ready for indoor flights.

Acceleration Adjustment

The drone starts in slow acceleration by default. While the drone is in the air, you can adjust the speed using the speed knob (FIG 2). Turn to the right for second gear (the remote control beeps twice) and to the right again for third gear (beeps three times). Turn to the left to switch back to second or first (low) gear.

[Diagram: Illustration showing the speed adjustment knob on the drone's underside (FIG. 2).]

Adjusting the Camera Angle

The camera angle can be adjusted during flight using the adjustment knob (FIG 3).

[Diagram: Illustration showing the camera angle adjustment knob on the drone (FIG. 3).]

Return-to-Home Function

During flight, press the function button (FIG 5). The drone will automatically ascend or descend to 50 meters, return to the takeoff location, and land.

[Diagram: Illustration of the remote control highlighting the function button (FIG. 5) and a flight path diagram showing a "Beginpunt" (start point) and "Eindpunt" (end point), with an indication to "press once to return".]

Functions in the App

In the drone app, you can control various functions by clicking on the drone logo. From there, you can control the following functions:

Also, from the app, you can control the drone:

1. Unlock
2. Take off
3. Have videos recorded
4. Have photographs taken
5. Have returns made
6. Have an emergency stop made
7. Control via your smartphone

Disclaimer

By using this manual, you agree to this disclaimer. TLS Commerce B.V. strives to provide complete, accurate, and up-to-date information in the manual and on the associated web pages. In case of questions or incorrect information, please contact TLS Commerce B.V. customer service. All information is intended for personal use. TLS Commerce B.V. is not responsible for damages resulting from use, incompleteness, or inaccuracy of the information when used carelessly. The information is subject to change without notice.

Information of the Company

TLS Commerce B.V. | Nuvance

Chamber of Commerce: 85524271

VAT no: NL863652591B01

Graafschap Hornelaan 116B
6004 HT Weert
The Netherlands