Novy Pendant User Manual

Product Information

? This product contains an ambient light source of energy efficiency class G.

? This product contains a functional light source of energy efficiency class F.

⚠️ The light source (LED only) and driver can only be replaced by a recognised installer.

Ensure an on-off switch is provided at the mains power supply.

Gesture Control (GC) Operation

The Gesture Control (GC) is operated by a sensor located in the centre of the light object, indicated by an icon. The sensor has a range of 15cm under the Novy Pendant.

Diagram Description: A visual representation shows the light fixture with a shaded area beneath it, labeled 'Sensor range' and 'max. 15cm'. Arrows indicate movement within this range.

Note: All movements lower than 15cm are not responded to by the sensor.

Switching the Lighting On and Off

The lighting can be activated in two ways:

1. By moving your hand from left to right or right to left underneath the sensor.
2. By holding your hand underneath the sensor for more than 1 second. 1️⃣ sec

Diagram Description: Illustrations show two methods: 1. A hand moving horizontally under the sensor. 2. A hand held stationary under the sensor for approximately 1 second, depicted with a pie chart.

Changing the Light Balance

You can adjust the light distribution from top to bottom:

• Balance more towards the top: Holding your hand closer to the sensor will move the light towards the top of the Novy Pendant.
• Balance more towards the bottom: Holding your hand further from the sensor (but no further than 15cm!) will move the light towards the bottom of the Novy Pendant.

Diagram Description: Diagrams illustrate hand positions relative to the sensor. Moving the hand closer (upward arrow ▲) shifts light up; moving it further away (downward arrow ▼) shifts light down.

Changing and Setting the Colour

Changing the Colour at the Top

By holding your hand close to the sensor for 2 seconds, the light on the top side of the Novy Pendant will change to a preset colour.

Diagram Description: A hand is shown held near the sensor for '2 seconds'.

Setting the Colour

If you want to change the colour of the mood setting:

1. First, go to mood mode in the preset colour (as described in the previous step).
2. Next, hold your hand under the sensor for another 4 seconds until the coloured light pulses. You are now in the colour setting mode.

Diagram Description: A hand is shown held under the sensor for '4 seconds', indicating the color setting mode.

Once you have reached the desired colour, remove your hand. After 4 seconds, the pulsing will stop, and the chosen colour will be set as the default colour and saved.

By moving your hand under the sensor, you can "scroll" through the available colours. You can scroll forward and backward by moving the hand either from left to right or right to left underneath the sensor.

Diagram Description: A hand is shown moving horizontally under the sensor to scroll through available colors, represented by a series of dots.

Service and Troubleshooting

If there is a fault, you can contact your (kitchen) supplier and/or Novy Customer Care Service.

For prompt and efficient service, it is necessary that the Novy Customer Care Service knows which type of appliance you have.

External Factors and Cleaning

External Factors Affecting Operation

The Novy products operate with infrared sensors. If there is an extraordinary amount of infrared light in the immediate vicinity of the fixture, this may adversely affect operation:

• Bright sunlight reflecting off shiny objects.
• Direct radiation from halogen spotlights or incandescent lamps at the underside of the fixture.
• Proximity sensor of mobile phones.

In case of excessive amounts of steam, the light fitting may possibly recognise this as a hand signal!

Cleaning

The fixture can be cleaned using simple soapy water. Do not use excess water. For removing stubborn stains, we recommend using a mild degreaser. Preferably use a microfibre cloth.

Caution: Cleaning the Sensor Film

Cleaning the black sensor film should be kept to a minimum to avoid scratch formation. Scratches on the foil can negatively affect the operation of the sensors. Clean the film with a microfibre cloth at all times.