Novy Wall Installation Guide
General Information
These are the mounting instructions for the Novy unit device. Carefully read the safety instructions, mounting instructions, and user manual before installation and putting it into operation.
The safety instructions are listed in a separate booklet supplied with the appliance and are also available on our website: www.novy.com.
Follow the safety instructions, mounting instructions, and user manual to prevent injury and material damage.
This manual uses several symbols. Their meanings are explained below:
- ?️ Indication: Explanation of an indication on the device.
- ⚠️ Information/Warning: This symbol indicates an important tip or a dangerous situation.
Installation Guidelines
This product contains an ambient light source of energy efficiency class F.
This product contains a functional light source of energy efficiency class E.
❗ The product should only be installed by a qualified and trained installer.
ℹ️ Light source (LED only) can only be replaced by a certified installer. [Diagram Description: A diagram showing an LED light module with arrows indicating that the light source (LED only) can be replaced by a certified installer.]
ℹ️ Driver can only be replaced by a certified installer. [Diagram Description: A diagram showing a driver unit with a 230V input and LED output, indicating it can only be replaced by a certified installer.]
❗ Turn off the power to the designated power cable during installation.
ℹ️ Provide an on-off switch at the mains power supply.
Supplies
Check if the necessary accessories are included.
- Black: 2x 7000017806
- White: 2x 7000017807
- Black: 2x 70000191
- White: 2x 70000183
- 1x 53005145
- 1x 70000206
Installation Instructions
Step 2A: Positioning
[Diagram Description: A line drawing showing the Novy Wall fixture positioned against a wall, with a horizontal line indicating the top of the fixture and a vertical line indicating the worktop. A dimension line shows a minimum distance of 450mm between the fixture and the worktop.]
Determine the desired position of the Novy Wall. Ensure there is at least 45 cm distance between the bottom of the fixture and the worktop to ensure safety and functionality.
Step 2B: Marking Brackets
[Diagram Description: A line drawing showing the Novy Wall fixture mounted on a wall, with mounting brackets attached. A dimension line labeled 'D' indicates the maximum distance between the center points of the brackets.]
Mark the location of the installation brackets on the wall. The maximum distance between the brackets (center point to center point) is shown in the table.
Product | D max (mm) | Product | D max (mm) |
---|---|---|---|
Novy Wall 95 | 735 | Novy Wall 215 | 1895 |
Novy Wall 125 | 1025 | Novy Wall 245 | 2185 |
Novy Wall 155 | 1315 | Novy Wall 275 | 2475 |
Novy Wall 185 | 1605 | Novy Wall 305 | 2765 |
Step 3: Attaching Brackets
[Diagram Description: Shows a hand attaching a bracket to the wall with screws. Another diagram shows two brackets mounted on the wall, with a spirit level indicating they are level.]
Attach the brackets, with the correct side upwards, to the wall. Ensure that the top of both brackets is level.
❗ ATTENTION: Use appropriate mounting material for the type of wall on which the fixture is being installed.
Step 4: Electrical Connection
[Diagram Description: Shows electrical wires (line, neutral, earth) emerging from a wall, and a hand connecting them to the fixture.]
Provide the electrical connection cable from the wall. Only line and neutral cables are needed; shield the grounding.
Steps 5A, 5B, 5C: Cable Preparation and Connection
5A: Prepare the electric cable. Use the insulation hose provided to protect the cable. Shield the earthing.
5B: Remove the orange cap from the driver in the luminaire. Strip the line and neutral cable.
5C: Use the insulation hose provided to shield the cables to below the orange cover. Connect the electrical cables according to the markings on the driver. Replace the orange cap on the driver.
[Diagram Description: A sequence of diagrams detailing the electrical connection process: preparing the cable, stripping wires, using a protective insulation hose, removing an orange cap from the driver, connecting wires to marked terminals on the driver, and replacing the cap.]
Step 6: Mounting the Fixture
[Diagram Description: Shows the Novy Wall fixture being placed onto the mounted brackets and then secured with Allen screws from underneath.]
Let the fixture rest on the brackets. After that, secure the fixture to the brackets using the Allen screws at the bottom of the brackets. Switch on the power and the device is ready to use.
❗ ATTENTION: Conceal any excess cable inside the fixture.
Company Information
Novy nv reserves the right at any time and without reservation to change the structure and the prices of its products.
Novy nv
Noordlaan 6
B - 8520 KUURNE
Tel. 0032 (0) 56/36.51.00
info@novy.com
www.novy.com