BISSELL AeroSwift 1808 Series Vacuum User Guide

Important Safety Instructions

WARNING: To reduce the risk of fire, electric shock, or injury, always follow basic safety precautions when using an electrical appliance. Read all instructions before using your vacuum.

• Do not leave the vacuum unattended while plugged in.
• Do not use outdoors or on wet surfaces.
• Keep children away from the appliance; do not allow it to be used as a toy.
• Use only as described in this User's Guide and with manufacturer-recommended attachments.
• Do not use with a damaged cord or plug. If the appliance is not working properly, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces. Do not run appliance over cord.
• Do not unplug by pulling on the cord. Grasp the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce airflow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn off all controls before plugging or unplugging.
• Use extra care when cleaning on stairs.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
• Do not pick up hard or sharp objects, such as glass, nails, screws, coins, etc.
• Do not use without filters in place.
• Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
• Do not use vacuum cleaner in an enclosed space filled with the vapors given off by oil base paint, paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapors.
• Keep appliance on a level surface.
• Do not carry the vacuum cleaner while it is running.
• Unplug before connecting or disconnecting the TurboBrush™ Tool.
• Use only on dry, indoor surfaces.

Polarized Plug: This appliance has a polarized plug. To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a proper outlet. Do not change the plug in any way.

What's In The Box?

Your vacuum cleaner may include the following standard accessories. Please refer to the carton contents list on the carton top flap to identify what should be included with your purchase.

• Base Unit
• Handle
• Upper Handle
• Hose
• Lower Hose
• Cord Wrap
• Extension Wand
• Crevice Tool (stored inside Extension Wand)
• Combination Dusting/Upholstery Tool
• TurboBrush® Tool

Product View

Diagrams illustrating the parts of the vacuum cleaner:

• 1. Handle
• 2. TurboBrush® Tool
• 3. Crevice Tool
• 4. Tank Release Button
• 5. Stretch Hose
• 6. Carry Handle
• 7. Extension Wand
• 8. Power Cord
• 9. Bottom-Empty Dirt Bin
• 10. Height Adjustment Knob
• 11. Combination Dusting/Upholstery Tool
• 12. Lower Hose
• 13. ON/OFF Pedal
• 14. Recline Pedal

Cord Release and Storage: Twist Cord Release down to quickly remove cord.

Assembly

WARNING: Do not plug in your vacuum until you are familiar with all instructions and operating procedures.

1. Insert handle into vacuum base until you hear a "click".
2. Wrap the hose up and around, then slide end into vacuum base until you hear a "click".
3. Push hose end into vacuum base until you hear a "click".
4. Push lower cord wrap in, aligning the two tabs, then turn clockwise (down) to lock into place.
5. Store the 2-in-1 Dusting Brush on side of vacuum.
6. Store Crevice Tool inside Extension Wand and store Extension Wand on side of vacuum.
7. Store TurboBrush® tool on front in holder.

NOTICE: Brushroll continues to turn while product is turned on and handle is in upright position. To avoid damage to carpet, rugs, furniture and flooring, avoid tipping vacuum or setting it on furniture, fringed area rugs, or carpeted stairs during tool use.

NOTICE: With brushroll on, do not allow cleaner to sit in one location for an extended period of time, as damage to floor can result.

Install Filter

WARNING: Before using your vacuum, make sure that the dirt container is in locked position and that the filter is in place. DO NOT operate your vacuum without the filter.

1. Press top of dirt tank to release it from the vacuum base.
2. To access the filter, twist the top of the tank counter-clockwise to unlock and reveal filter.
3. Remove foam filter. Hand wash in warm water; mild detergent may be used if desired. Rinse well and air dry thoroughly. Replace filter if necessary.
4. Make sure the filter is completely dry before placing it back into the tank top.
5. Return the tank's top, aligning the tabs and twisting clockwise to lock.
6. Return tank, pressing firmly until you hear a "click".

Power On & Settings

1. Turn the dial on the foot of the vacuum to the desired setting.
• Bare Floor Setting: For bare floors or low pile carpet.
• High Carpet Setting: For pile and most shag carpet.
2. Press down once on the red ON/OFF pedal located on the lower back of the vacuum to turn ON. Press down again to turn OFF.

TIP: For optimal carpet cleaning performance, adjust to the lowest practical setting. If your vacuum is difficult to push, adjust to the next higher setting.

Above Floor Cleaning

1. Pull hose up and out of vacuum base to attach your desired tool.
2. For extended reach, attach the extension wand to the hose first and then your desired tool.

Maintenance: Empty Dirt Tank

WARNING: To reduce the risk of electrical shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks.

1. Press the release button at the top of the dirt tank to remove it from the vacuum.
2. Hold dirt tank over a trash container and press lid release button to empty. Close lid and return tank to vacuum base.
3. Empty once tank is full.

Maintenance: Clean Tank & Cyclone

1. Remove the dirt tank and twist its top counter-clockwise to unlock and remove.
2. Grab the top of the Cyclone assembly to remove. Clean with warm water and mild detergent. Wipe inside of tank with a damp cloth.
3. Replace the Cyclone assembly with tank to reassemble.
4. Place the top back on the dirt container by aligning the tab, then twist clockwise to lock.
5. Return the fully assembled tank to the vacuum base and press firmly until you hear a "click".

NOTE: Let parts dry completely before returning them to vacuum for use.

Maintenance: Filter

WARNING: Do not operate vacuum with damp or wet filters, as well as without filters or the Dirt Container in place. Allow components to dry before reassembling the Dirt Container.

1. Press tank release button and remove dirt tank.
2. To access filter, turn top of tank counter clockwise and pull up to separate.
3. Remove foam filter. Hand wash in warm water; mild detergent may be used if desired. Rinse well and air dry thoroughly. Replace filter if necessary.
4. Make sure the filter is completely dry before placing it back into the tank top.
5. Return the tank's top, aligning the tabs and twisting clockwise to lock.
6. Return tank, pressing firmly until you hear a "click".

Maintenance: Check Brush & Belt

Tools needed: Phillips head screwdriver.

1. Unplug vacuum, turn it over and remove the 5 silver Phillips head screws to remove the bottom cover.
2. Pull brush roll out of its housing, freeing it from the belt.
3. Inspect brush roll by resting it on its end and giving it a spin. Brush roll should spin freely and make several rotations with one flick. If not, replace brush roll. Inspect belt; replace if it appears damaged.
4. Reinstall belt onto the motor gear. Reinstall belt onto brush roll and place it back in. Position the end of the brush roll opposite the belt so it aligns with the tab. The end closer to the belt will slide onto the tab without needing to be spun.
5. Reinstall the bottom cover by screwing in the 5 screws. Spin the brush roll one full turn by hand to center the belt properly.

Troubleshooting

WARNING: To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

Parts & Supplies: For Parts and Supplies, go to www.BISSELL.ca and enter your model number in the search field.

Warranty

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by E-mail, telephone, or regular mail as described below.

Limited Two-Year Warranty: Subject to the *EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY identified below, upon receipt of the product BISSELL will repair or replace (with new or remanufactured components) at BISSELL's option, any defective or malfunctioning part for two years from the date of purchase by the original purchaser, free of charge.

Warranty Exclusions: This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, unauthorized repair, or any other use not in accordance with the User's Guide is not covered.

NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.

Service: If your BISSELL product should require service:

• Contact BISSELL Consumer Care: Call 1-800-263-2535. Monday- Friday 8am -10pm ET, Saturday 9am - 8pm ET, Sunday 10am - 7pm ET.
• Website: www.BISSELL.ca
• E-mail: www.BISSELL.ca/email-us

Please do not return this product to the store. Other maintenance or service not included in the manual should be performed by an authorized service representative. For any questions or concerns, BISSELL is happy to be of service. Contact us directly at 1-800-263-2535.

Register your product today!

Registering is quick, easy and offers you benefits over the lifetime of your product.

• Faster Service: Supplying your information now saves you time should you need to contact us with questions regarding your product.
• Product Support Reminders and Alerts: We'll contact you with any important product maintenance reminders and alerts.
• Special Promotions: Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.bissell.ca/registration!

When contacting BISSELL, have model number of cleaner available.

Visit the BISSELL website: www.bissell.ca

Please record your Model Number: ____________________

Please record your Purchase Date: ____________________

NOTE: Please keep your original sales receipt. It provides proof of purchase date in the event of a warranty claim. See Warranty on page 11 for details.

For cleaning tips and more visit www.BISSELL.ca or find us at:

BISSELL | BISSELLClean | BISSELLClean | BISSELL | You Tube

We can't wait to hear from you! Rate this product and let us (and millions of your closest friends) know what you think!

www.bissell.ca