DELUX Vertical Mouse User Manual

System Requirements

Windows 7/Windows 8/Windows 10/macOS.

Functions

The DELUX Seeker Vertical Mouse features the following functions:

• 1 OLED Screen: Displays connection status and mode.
• 2 Forward Button
• 3 Backward Button
• 4 Left Button
• 5 Right Button
• 6 Charging Indicator: Shows charging status.
• 7 Scroll Wheel
• 8 DPI Button: For adjusting DPI settings.
• 9 Palm Rest
• 10 Thumb Scroll Wheel
• 11 ON/OFF Switch
• 12 Mode Indicator: Indicates the current connection mode.
• 13 Mode Switching Button: Used to switch between connection modes.
• 14 Receiver Storage Slot
• 15 Receiver

Diagram Description: The manual includes diagrams illustrating the mouse's layout and the USB receiver.

Charging Mode

Connect the mouse to a USB Type-C port for charging. The indicator light turns red while charging and turns off when fully charged.

Connectivity Modes

Wired/2.4G Wireless/Bluetooth Switching

Tap the mode switching button to change the connection mode. The corresponding mode indicator will flash, and the OLED screen will display the connected mode. The indicator light turns off when connected via wired mode.

Connected Mode Details:

• Wired Mode: Connect the mouse via USB Type-C. Tap the switching button until the light turns off. This mode is available when the mouse is turned ON or OFF.
• 2.4G Wireless Mode: Turn on the mouse after inserting the receiver into the device. Tap the switching button to enter 2.4G wireless mode. The mouse operates when the corresponding indicator light is off. To reset the mode, press and hold the switching button for approximately 3 seconds; the indicator light will flash quickly and then turn off upon successful reset.
• BT Mode: Turn on the mouse and tap the switching button to enter BT1/BT2 mode. The indicator light flashes to signify BT mode. Pressing and holding the switching button for about 3 seconds will cause the indicator light to flash quickly. You can then find "BT5.0MOUSE1" or "BT5.0MOUSE2" to connect. The indicator light will turn off upon successful connection.

Light Mode Switching

Press the right button and backward button simultaneously to switch between 5 different light modes. The driver software can also be used to adjust the backlight.

Automatic Sensing Light

The light sensation is enabled by default. The backlight turns off when your palm is close to the mouse. To turn off the light sensation, press and hold the right and left buttons simultaneously for about 3 seconds until the light flashes white twice. To re-enable the light sensation, long-press the right and left buttons again.

Hot Key to Close Side Button Function

Press and hold the forward button and backward button for 3 seconds to disable these two buttons. Long-press them again for 3 seconds to re-enable the function.

DPI Switching

Tap the DPI button to cycle through DPI settings:

• 800 DPI (red light)
• 1200 DPI (green light)
• 1600 DPI (blue light)
• 2400 DPI (purple light)
• 4000 DPI (yellow light)

Successful DPI switching is indicated by the corresponding light flashing twice. The default DPI is 1200 (range 600-4000).

Report Rate

• Wired/2.4G Mode: 125Hz, 250Hz, 500Hz, 1000Hz
• BT Mode: 125Hz

The default report rate is 500Hz, which can be adjusted via the driver software.

Thumb Scroll Wheel

• Scrolling up moves the cursor to the left.
• Scrolling down moves the cursor to the right.

This function can be utilized in office software, browsers, and other applications.

Driver Installation

• Installation: Download the driver from the official DELUX website: www.deluxworld.com.
• Setting: Open the driver software to configure the mouse functions.
• Multi-group File Configuration:
  • Click "+" on the top-left of the interface to create a new configuration file.
  • Click the trash can icon [?️] to delete the current configuration file.
  • Click the copy icon [?] to copy the current configuration file.
  • Click the rename icon [✏️] to rename the current configuration file.
• Light Setting: Click "Light setting" to customize the lighting effects.
• Button Setting: Click "Button settings" to assign functions to the mouse buttons. Click the checkmark icon [✔️] after completing all settings.
• Macro Management: Click "Macro management" to create and manage macros. Click "+" to create a new macro, then click "REC" to start recording. Press the desired keys on your keyboard during recording. Click "STOP" to end the recording. To import a macro, select the button to set, click "Macro function", choose the macro name, and then click "save" to finalize the setting.
• DPI Setting: Click "Other settings" to adjust DPI values.
• Default Settings: Click the reset icon [?] to reset settings to default, then click "OK" to confirm.

Diagram Description: The manual includes screenshots of the DELUX driver software interface, demonstrating light settings, button assignments, macro management, and DPI configuration.