Aveek F-5A Professional 5-Channel Audio Mixer with Effects Processor

1. Welcome

Thank you for purchasing the F-5A audio mixer. Please read this manual carefully for proper use of your F-5A audio mixer. Should you need technical assistance, please email our technical help at "all-after-sales@outlook.com".

2. Main Features

• 3 Mic + 2 Stereo Line Inputs: 3 XLR Line input jacks to connect mics or guitar, 1 pair 6.35mm and 1 pair 3.5mm RCA stereo inputs jacks to connect CD players/keyboards/computers.
• 48V Phantom Power: The mixer has 1-3 channel XLR inputs with phantom power. You can feel free to switch 48V phantom power and ultra-low noise distortion, enabling the audio mixer to be used with condenser microphones.
• 2-band EQ/gain controls/Reverb and Delay Effect: Highly accurate LED Peak Level Indicator. Easily adjust the high and low frequencies of each channel with the onboard 2-band EQ and gain controls. You can even add delay or reverb effects in your mix.
• Recording and Playing Music: Connect external USB flash drives, PCs, phones, and tablets for recording and playing. At the same time, it is also possible to record the same audio in progress to a USB flash drive for output.
• Bluetooth Connection: This audio mixer enables wirelessly streaming music from Pad, Phone, Tablets, Computer, and more Bluetooth devices to mix music.
• Headphone monitor: 3.5mm headphone jack; you can plug in headphones at any time to monitor the sound and volume.

3. Included Accessories

• Audio mixer * 1
• USB to Type-C Cable * 1
• USB Cable (59 Inch) * 1
• AC power adapter * 1

4. Panel Introduction

The mixer features a comprehensive panel with various input/output jacks, controls, and indicators.

• 1 [MIC/LINE] Mono Input jack: Available for XLR input channels 1-3. Used to connect microphones, musical instruments, or audio equipment (CD players, etc.). These jacks support both XLR and phone plugs.
• 2 [PAD] Switch: Available for XLR input channels 1-3. Turning on this switch attenuates the input signal. If you hear distortion or the [PEAK] LED ⑦ lights up, turn on the switch.
• 3 [HPF] switch: Available for XLR input channels 1-3. Enables the high-pass filter, attenuating frequencies below 80 Hz. Use this to minimize unwanted vibrations and breath sounds picked up by the microphone.
• 4 [GAIN] knob: For XLR input channels 1-3, this determines the basic volume. Adjust to make the corresponding [PEAK] LED ⑦ flash briefly when singing and playing at maximum volume. For channels 4-5/Bluetooth/USB input, the gain knob is shared and has independent volume control compared to channels 1-3.
• 5 Equalizer (EQ) knob: For XLR input channels 1-3, use the [HIGH] and [LOW] knobs to adjust sound quality. For channels 4-5/Bluetooth/USB input, the EQ knob is shared.
• 6 [EFF] Effect switch: Adjusts the effect volume for channels 1-3. Channels 4-5/Bluetooth/USB modules have no reverberation effect.
• 7 [PEAK] LED: Lights up when the input signal volume or the volume after the equalizer is too high (3dB below clipping distortion). If it lights up frequently, turn the [GAIN] knob ④ to the left to decrease the volume.
• 8 [LEVEL] knob: Adjusts the volume balance between each channel.
• 9 [ST/USB] switch: Switches between channels 3-4 or Bluetooth/USB module. Press for Bluetooth/USB module, do not press for channels 3-4 and computer input. Bluetooth and USB functions cannot be used simultaneously.
• 10 RCA L/R Line Output jack: For output connections to devices with RCA jacks.
• 11 RCA L/R Line Input jack: For input connections to devices with lotus line jacks (e.g., CD player, mobile, computer, electronic organ).
• 12 6.35mm L/R Line Input jacks: For input connection to devices with 6.35mm-line jacks (e.g., CD player, mobile, computer, electronic organ).
• 13 6.35mm L/R Line Output jacks: For output connection to devices with 6.35 line socket equipment (e.g., active speaker, power amplifier).
• 14 L/R XLR Female Output jacks: For output connection to devices with 6.35 line socket equipment (e.g., power amplifier, active speaker).
• 15 [PAD +48V] Switch/LED: Available for 1-3 XLR input Channels. When switched on, the LED indicates that +48V phantom power is applied to the [MIC/LINE] mono input port 1. Use with condenser microphones that require phantom power. Ensure the switch is off if phantom power is not needed. Do not connect/disconnect cables on channels 1-3 when the switch is on. Set [LEVEL] knobs to minimum before operating this switch.
• 16 USB input: For USB port device input (e.g., PC, USB Stick, MP3 devices) for music playback and recording.
• 17 Display: Shows USB mode or Bluetooth mode.
• 18 MP3 player controller: Buttons for playback pause, next song, previous song, and switching sound source mode.
• 19 [DELAY] Delay effect knob: Adjusts the intensity of the delay effect for XLR input Channels 1-3.
• 20 Level meter: Displays L and R levels in 5 stages: "+10", "+6", "+0", "-3", and "-10" dB.
• 21 [REPEAT] Reverb effect knob: Adjusts reverberation effect processing for XLR input Channels 1-3.
• 22 [PHONES] output jack: Used to connect headphones.
• 23 [PHONES] knob: Adjusts the volume of the sound output from the [PHONES] jack.
• 24 [MAIN] knob: The main signal output control knob.
• 25 [DC5V 1A] Type-C power socket: Used to connect the included power cord.
• 26 [PC/REC] indicator: Lights up when a computer device is connected.
• 27 PC output port: Outputs the stereo bus sound to the computer for recording or audio input.
• 28 Power switch: Controls the mixer's power.

5. General Specifications

6. Compatible Devices and Connection Methods

The mixer can be connected to various devices including microphones, musical instruments, active speakers, power amplifiers, computers, USB drives, phones, and Bluetooth-compatible devices.

Input & Output Summary:

• MIC XLR INPUT: XLR input jacks x 3
• 6.35MM INPUT: 6.35mm L/R Line input jacks x 1 pair
• RCA INPUT: RCA L/R Line input jacks x 1 pair
• USB/Bluetooth INPUT: USB input & record x 1, Bluetooth wireless input
• REC OUT: XLR female output x 1 pair
• MAIN OUT: RCA L/R Line output x 1 pair
• MONITOR OUT: 3.5mm monitor output jack x 1

7. How to Use the Audio Mixer?

STEP 1: Setup

1. Connect the Type-C power cable to the mixer, then connect the supplied AC adapter.
2. Adjust all level control knobs to zero. Includes [Gain] knob (red), [Level] knob (blue), and [Main] knob (white). Set the equalizer knob (green) to the center "12 o'clock" position.
3. Turn on the power switch button.
4. Connect the output device (active speakers or power amplifier + passive speakers) to the output device jack of the mixer.
5. Connect the input devices in the following order: microphone, instrument, audio device, computer, U Stick or Bluetooth, speakers.

NOTICE: Follow this order to avoid loud, unexpected noise from the speakers. Reverse the order when turning the power off.

STEP 2: Operation

1. If you connect a device with a high output level (e.g., a CD player or an electric keyboard) to channels 1-3, press the [PAD] switch of the corresponding channel.
2. If using condenser microphones, turn on the [PAD+48V] switch.
3. Set the [LEVEL] knob as required to adjust the volume balance between the corresponding channels.

NOTICE: There are three functions to adjust the volume: [PAD], [GAIN], and [LEVEL]. Once the [PAD] switch and [GAIN] knob have been set, do not adjust these controls as much as possible. Generally, the volume is adjusted with the [LEVEL] knob.

8. Operating Steps for Computer Recording

STEP 1: First, connect the PC or laptop to the mixer using a cable to power it on. Then, directly open the recording software to record (no need to install a driver).

STEP 2: Before connecting to the PC or laptop to record, set the computer as follows:

Windows system settings

1. Open the Start menu, then click Control Panel.
2. Open the sound preferences from the Control Panel folder.
3. Click "Record" and set the microphone to the default value to start recording.

Apple system settings

1. Open the "System Preferences" application.
2. Find "Sound" and click to open it.
3. Click to open the "Output" interface to select the microphone and start recording.

9. How to record via USB jack

1. Plug in a USB stick or flash drive.
2. Press the MODE button until "USB REC" is shown on the LCD and you hear the voice prompt "Recording Mode". Recording will start automatically to USB.
3. Press the II button to start or pause recording.
4. Press the MODE button to finish recording and save the file in MP3 format.

10. Operating Steps for Bluetooth Playback

1. Press the MODE button until "BT" is shown on the LCD and you hear the voice prompt "The Bluetooth device is ready to pair". If Bluetooth is not connected, "BT" will keep flashing.
2. Open Bluetooth mode on your phone, click "F-5A" to connect successfully, and you will hear the voice prompt "Bluetooth connect successful", then play music.
3. Press the II button to start or pause music. Press the ◄◄ and ►► buttons to switch songs.

NOTE: When using Bluetooth and USB functions, please press this key ▶.

11. Operating Steps for USB Play Music

1. Plug in a USB stick, flash drive, or MP3.
2. Press the MODE button until "MP3" is shown on the LCD and you hear the voice prompt "Music Play Mode". Music will play automatically.
3. Press the II button to start or pause music. Press the ◄◄ and ►► buttons to switch songs.

NOTE: When using Bluetooth and USB functions, please press this key ▶.

NOTE: Bluetooth and USB functions are only available as one of the two options and cannot be used simultaneously.

12. PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING. Please keep this manual in a safe place for future reference.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following:

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire, or other hazards. These precautions include, but are not limited to, the following:

Power supply/AC power adaptor

• Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord. Do not place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it.
• Only use the voltage specified as correct for the device. The required voltage is printed on the name plate of the device.
• Use the specified adaptor (MU18 or PA-130, or an equivalent recommended by Aveek) only. Using the wrong adaptor can result in damage to the instrument or overheating.
• Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.
• Do not cover or wrap the AC power adaptor with a cloth or blanket.
• Remove the electric plug from the outlet when the device is not to be used for extended periods of time, or during electrical storms.
• When removing the electric plug from the device or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.

Location

• Do not place the device in an unstable position where it might accidentally fall over.
• Do not place the device in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn the power off and disconnect the plug from the outlet. Even when the power is turned off, electricity is still flowing to the product at a minimum level.
• When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet.

Connections

• Remove the power plug from the AC outlet when cleaning the device.

Maintenance

• Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum.
• Aveek cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.

Handling caution

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings on the device. If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Aveek service personnel.
• Do not rest your weight on the device or place heavy objects on it, and avoid using excessive force on the buttons, switches, or connectors.
• Do not use speakers or headphones for a long period of time at a high or uncomfortable volume level, as this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.

Water warning

• Do not expose the device to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles, or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the device, turn off the power immediately and unplug the power cord from the AC outlet. Then have the device inspected by qualified Aveek service personnel.
• Never insert or remove an electric plug with wet hands.

Fire warning

• Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire.