Yaheetech 591761 Multi-Shelf Storage Unit
Model Number: 591761
Introduction
Please read this instruction manual carefully before attempting to install this product. This manual is available in multiple languages.
Important Information & Recommendations
- ? Assembly is recommended for 1 or more people.
- ⏱️ The expected assembly time is approximately 1 hour.
- ?? This product is not intended for use by children.
- ? Keep away from fire or other heat sources.
- ? It is recommended to wear protective gloves during assembly.
Assembly Advice:
Follow the instruction manuals and use a protective pad or cover to avoid damage to the product and floor during assembly. ❌ Do not place the product directly on the floor without protection. ✔️ Use a protective pad.
Parts List
| Part ID | Description | Quantity |
|---|---|---|
| 1 | Top Panel | x1 |
| 2 | Shelf Panel | x1 |
| 3 | Shelf Panel | x1 |
| 4 | Shelf Panel | x1 |
| 5 | Back Panel | x1 |
| 6 | Bottom Panel | x1 |
| 7 | Left Side Frame | x1 |
| 8 | Right Side Frame | x1 |
| 9 | Drawer Side Panel | x4 |
| 10 | Drawer Back/Front Panel | x1 |
| 11 | Drawer Bottom Panel | x2 |
| 12 | Drawer Front Panel (with handle cutout) | x2 |
| 13 | Drawer Base Panel | x2 |
| A | Cam Lock Bolt | x12 |
| B | Cam Lock Nut | x12 |
| C | Wooden Dowel | x20 |
| D | Screw | x16 |
| E | Screw | x2 |
| F | Metal Bracket | x2 |
| G | Metal Bracket with Chain | x1 |
| H | Wall Anchor Plug | x8 |
| I | Screw for Wall Anchor | x8 |
Assembly Instructions
Step 1: Assemble Drawer Sides
Take two drawer side panels (9) and one drawer back/front panel (10). Insert cam lock bolts (A) into the pre-drilled holes on the edges of panel (10). Align the side panels (9) with panel (10) and secure by inserting cam lock nuts (B) into the corresponding holes on panels (9) and turning them clockwise until tight. Repeat this process to create the second drawer frame.
Step 2: Insert Drawer Base
Slide one drawer base panel (13) into the grooves on the inner sides of the assembled drawer frame from Step 1. Ensure it sits flush.
Step 3: Attach Drawer Front
Take a drawer front panel (12) (with handle cutout). Align it with the front of the drawer frame. Secure it to the drawer side panels (9) using screws (D). Repeat Steps 1-3 to assemble the second drawer.
Step 4: Prepare Shelf Panels
Attach two metal brackets (F) to the underside of shelf panels (2) and (3) using screws (E). These brackets will help secure the shelves.
Step 5: Assemble Main Frame (Lower Part)
Insert cam lock bolts (A) into the pre-drilled holes on the top edges of the left side frame (7) and right side frame (8). Align these side frames with the corresponding holes on the bottom panel (6) and shelf panels (2) and (3). Secure by inserting cam lock nuts (B) into the holes on panels (6), (2), and (3) and turning them clockwise until tight.
Step 6: Attach Inner Panels
Insert wooden dowels (C) into the pre-drilled holes on the inner edges of the side frames (7) and (8). Attach the shelf panels (2), (3), and (4) by aligning them with the dowels and securing them with screws (D) through the side frames.
Step 7: Secure Inner Panels
Insert cam lock nuts (B) into the corresponding holes on the shelf panels (2), (3), and (4) and turn them clockwise to secure the panels to the side frames.
Step 8: Install Bottom Panel
Slide the bottom panel (6) into the grooves located at the bottom of the assembled unit. Ensure it is fully seated.
Step 9: Prepare for Back Panel
Insert wooden dowels (C) into the pre-drilled holes along the top edges of the side frames (7) and (8), and along the back edge of the unit where the back panel will attach.
Step 10: Secure Unit Structure
Insert cam lock nuts (B) into the corresponding holes on the unit's side and back panels and turn them clockwise to secure the structure.
Step 11: Install Back Panel
Carefully slide the back panel (5) into the grooves on the rear of the unit. Ensure it is fully inserted and fits snugly.
Step 12: Attach Top Panel
Insert wooden dowels (C) into the pre-drilled holes on the top edges of the side frames (7) and (8). Place the top panel (1) onto the unit, aligning it with the dowels. Secure the top panel from underneath by inserting screws (D) through the side frames into the top panel.
Step 13: Secure Top Panel
Insert cam lock nuts (B) into the corresponding holes on the underside of the top panel (1) and turn them clockwise to fully secure the top panel.
Step 14: Install Wall Anchoring Hardware
Attach the metal brackets (H) to the back of the unit using screws (I). These are for securing the unit to the wall.
Step 15: Insert Drawers
Slide the two assembled drawers into their designated slots within the unit.
Wall Anchoring Guide
For safety, it is strongly recommended to anchor this unit to the wall to prevent tipping. Follow the appropriate steps based on your wall material:
Drywall or Plaster with Wood Stud:
- Mark the desired attachment point(s) on the wall at the appropriate height, ensuring it is positioned over a wood stud.
- Drill a pilot hole with a diameter matching the screw into the wood stud at the marked height.
- Secure the screw firmly into the wood stud as shown in the diagram.
Drywall without Wood Stud:
- Mark the desired attachment point(s) on the wall at the appropriate height.
- Drill a hole with a diameter matching the plastic anchor through the wall at the marked height.
- Drive the plastic anchor plug into the hole, using a hammer if needed.
- Insert the screw into the plastic anchor plug firmly, as shown. Do not over-tighten.
Masonry (Brick, Concrete, etc.):
- Mark the desired attachment point(s) on the wall at the appropriate height.
- Drill a hole with a diameter and depth matching the plastic anchor through the wall at the marked height.
- Drive the plastic anchor plug into the hole, using a hammer if needed.
- Insert the screw into the plastic anchor plug firmly, as shown. Do not over-tighten.
Important: If the screw cannot be securely fastened to the wall, please keep the product away from children. If your wall material is not listed here, or if you have any questions, consult your local hardware store.
Product Care Instructions
- Use a soft, clean cloth or sponge to gently wipe the outer surface of the product to remove dust and dirt.
- Avoid using chemical cleaners or harsh solvents to prevent damage to the appearance of the product.
- Inspect the fittings (bolts, screws, nuts, etc.) every 3 months and re-tighten them every 6 months if necessary.
- Avoid direct sunlight.
- If the product shows structural damage or poses a safety hazard, stop using it until it is repaired.
Customer Support
If you are not entirely satisfied with your purchase, please feel free to contact us by following these steps:
- Go to 'Your Orders'.
- Find your order in the list.
- Select 'Problem with order'.
- Choose your topic from the list displayed.
- Select 'Contact seller'.
Contact Information:
US:
YAHEE TECHNOLOGIES CORP
Address: 1532 S VINEYARD AVE ONTARIO CA 91761
UK:
Monumart Limited
Address: Europa House, Europa Way, IP15DL, Ipswich.
Manufacturer (PRC):
Yahee GmbH
Höpfigheimer Straße 11, 74321 Bietigheim-Bissingen
Manufacturer (Japan):
亜訊国際株式会社
Address: 東京都新宿区西新宿七丁目5番6号 新宿ダイカンプラザ756館804
Email: info@yaheetech.shop
Specifications
- Dimensions: 300mm (Width) x 300mm (Depth) x 890mm (Height)
- Surface Material: MDF
- Surface Finish: Lacquer coating
- Care Instructions: Avoid direct sunlight or heat. Do not place hot pots, kettles, etc., directly on the surface.
Download Manual
You can also download the electronic Installation Manual from the 'Product guides and documents' section of the advertising page. ?
