Vanity Table Manual 85023
Thank you for purchasing this product. Please follow these instructions carefully for assembly.
Parts List
| Label | Description |
|---|---|
| Ax1 | Top surface with integrated LED lighting and controls. |
| Bx1 | Mirror with a decorative frame. |
| Cx1 | Top panel of the drawer unit. |
| Dx1 | Bottom panel of the drawer unit. |
| Ex1 | Left side panel of the drawer unit. |
| Fx1 | Right side panel of the drawer unit. |
| Gx2 | Vertical drawer dividers. |
| Hx2 | Horizontal drawer dividers. |
| Ix2 | Drawer side panels. |
| Jx1 | Drawer front panel. |
| Kx3 | Drawer back panels. |
| Lx3 | Drawer bottom panels. |
| Mx3 | Drawer side support rails. |
| Nx3 | Drawer back support rails. |
| Ox2 | Drawer unit back panels. |
| Px1 | Leg frame for the table surface. |
| Qx1 | Base for the mirror. |
| Rx3 | Drawer bottom support rails. |
Hardware List
| Item | Description | Quantity |
|---|---|---|
| 1 ? | Two In One Screw (6x28mm) | 60pcs + 2pcs |
| 2 ⚙️ | Two In One Nut (10x12mm) | 60pcs + 2pcs |
| 3 ? | Wood Chipping (6x30mm) | 8pcs + 2pcs |
| 4 ? | Guide&Screw (3x12mm) | 24pcs + 6pcs |
| 5 ? | Small Non-slip pads | 6pcs + 2pcs |
| 6 | Backboard Card Strip (774mm) | 1pcs |
| 7 ?? | Fixing Clip & Screw (3x16mm) | 8pcs + 1pcs |
| 8 ? | Screw (6x28mm) | 7pcs |
| 9 ?? | Corner Code & Screw (3.5x12mm) | 8pcs + 1pcs |
| 10 ? | Big Non-slip pads | 1pcs |
| 11 ?️ | Anti tipping hardware (includes 3.5x12mm screw, 2x washer, 4x45mm screw, wall plug) | 1 set |
| AC/DC Adapter (12V=3.0A) | 1pcs | |
| Double-head screwdriver | 1pcs |
Product Structure Decomposition
This diagram shows an exploded view of the vanity table, illustrating how the main components (labeled A through Q) fit together to form the complete unit. It provides an overview of the structure before assembly begins.
Assembly Instructions
Step 1
Attach the drawer front panel (J) to the drawer back support rail (R) using two 'Two In One Screws' (1 ?) and two 'Two In One Nuts' (2 ⚙️).
Diagram shows part J being connected to part R with screws and nuts. A close-up shows how the screw passes through J and R, and the nut is secured on the other side.Step 2
Attach the drawer side support rails (M) and drawer back panels (K) to the assembly from Step 1. Use 'Two In One Nuts' (2 ⚙️) for connection.
Diagram shows parts M and K being attached to the structure formed in Step 1, using nuts.Step 3
Slide the drawer bottom panel (N) into the grooves of the assembled drawer sides and back.
Diagram shows panel N being inserted into the channels created by parts J, M, K, and R. An arrow indicates the direction of insertion.Step 4
Attach the drawer bottom panel (L) to the drawer front panel (J) using 'Two In One Screws' (1 ?).
Diagram shows part L being attached to the front of the drawer assembly (part J) using screws.Step 5
Attach the drawer side support rails (M) and drawer back panels (K) to the assembly from Step 4. Use 'Two In One Nuts' (2 ⚙️) for connection.
Diagram shows parts M and K being attached to the structure formed in Step 4, using nuts.Step 6
Slide the drawer bottom panel (N) into the grooves of the assembled drawer sides and back.
Diagram shows panel N being inserted into the channels created by parts J, M, K, and L. An arrow indicates the direction of insertion.Step 7
Attach the drawer side panels (I) to the drawer bottom support rails (R) using 'Two In One Screws' (1 ?).
Diagram shows part I being attached to part R using screws.Step 8
Attach the drawer side support rails (M) and drawer back panels (K) to the assembly from Step 7. Use 'Two In One Nuts' (2 ⚙️) for connection.
Diagram shows parts M and K being attached to the structure formed in Step 7, using nuts.Step 9
Slide the drawer bottom panel (N) into the grooves of the assembled drawer sides and back.
Diagram shows panel N being inserted into the channels created by parts I, M, K, and R. An arrow indicates the direction of insertion.Step 10
Attach the drawer bottom panel (L) to the drawer side panels (I) using 'Two In One Screws' (1 ?).
Diagram shows part L being attached to the side panels of the drawer assembly (part I) using screws.Step 11
Attach the drawer side support rails (M) and drawer back panels (K) to the assembly from Step 10. Use 'Two In One Nuts' (2 ⚙️) for connection.
Diagram shows parts M and K being attached to the structure formed in Step 10, using nuts.Step 12
Complete the drawer assembly by attaching the drawer slides (a) to the sides of the drawer box. Repeat these steps to assemble all required drawers.
Diagram shows drawer slides being attached to the assembled drawer box. The quantity 'x2' indicates this process is for two drawers.Step 13
Attach the support piece (H) to the bottom panel (D) using two 'Two In One Screws' (1 ?).
Diagram shows part H being screwed onto part D. A close-up shows the screw insertion.Step 14
Attach the support piece (H) to the bottom panel (D) using two 'Two In One Nuts' (2 ⚙️).
Diagram shows part H being attached to part D using nuts. A close-up shows the nut being tightened.Step 15
Attach the drawer slides (b and c) to the inner side of the right cabinet panel (F) using 'Guide&Screws' (4 ?).
Diagram shows multiple drawer slides being screwed onto the panel F. Multiple screw points are indicated.Step 16
Attach drawer slides to the inner side of the right cabinet panel (F) using 'Guide&Screws' (4 ?).
Diagram shows drawer slides being screwed onto panel F. The text "This hole is a reinforced fixing hole which can be installed as required" is noted.Step 17
Attach the drawer slides (b and c) to the inner side of the left cabinet panel (E) using 'Guide&Screws' (4 ?).
Diagram shows multiple drawer slides being screwed onto the panel E. Multiple screw points are indicated.Step 18
Attach drawer slides to the inner side of the left cabinet panel (E) using 'Guide&Screws' (4 ?).
Diagram shows drawer slides being screwed onto panel E. The text "This hole is a reinforced fixing hole which can be installed as required" is noted.Step 19
Attach the left cabinet panel (E) to the bottom panel assembly (D) using 'Two In One Screws' (1 ?) and 'Wood Chippings' (3 ?). Secure with 'Two In One Nuts' (2 ⚙️).
Diagram shows panel E being connected to the base assembly. A close-up shows the screw and dowel insertion, and another shows the nut being tightened.Step 20
Attach the left cabinet panel (D) to the base assembly (E) using 'Two In One Nuts' (2 ⚙️).
Diagram shows panel D being attached to panel E using nuts. A close-up shows the nut being tightened.Step 21
Attach the vertical drawer dividers (G) and horizontal drawer dividers (H) to the left cabinet panel (E) using 'Two In One Nuts' (2 ⚙️).
Diagram shows parts G and H being attached vertically and horizontally to panel E using nuts.Step 22
Attach the vertical drawer dividers (G) and horizontal drawer dividers (H) to the left cabinet panel (E) using 'Wood Chippings' (3 ?).
Diagram shows parts G and H being attached to panel E using dowels.Step 23
Attach the right cabinet panel (F) to the base assembly (E) using 'Two In One Screws' (1 ?).
Diagram shows panel F being attached to panel E using screws. A close-up shows the screw insertion.Step 24
Attach the right cabinet panel (F) to the assembled structure using 'Two In One Nuts' (2 ⚙️).
Diagram shows panel F being attached to the cabinet structure using nuts. A close-up shows the nut being tightened.Step 25
Apply the 'Big Non-slip pads' (5 ?) to the bottom corners of the assembled cabinet. Tear off the release paper before sticking.
Diagram shows the non-slip pads being applied to the bottom edges of the cabinet.Step 26
Place the drawer unit back panels (O) and the 'Backboard Card Strip' (6) onto the back of the cabinet structure in the indicated order.
Diagram shows two panels labeled 'O' and a strip labeled '6' being positioned on the rear of the cabinet. Arrows indicate the direction of placement.Step 27
Secure the drawer unit back panels (O) using 'Wood Chippings' (3 ?).
Diagram shows dowels being inserted to secure the back panels.Step 28
Attach the top panel (C) to the cabinet structure using 'Two In One Screws' (1 ?).
Diagram shows the top panel C being attached to the cabinet using screws. A close-up shows the screw insertion.Step 29
Secure the top panel (C) to the cabinet structure using 'Two In One Nuts' (2 ⚙️).
Diagram shows the top panel C being secured with nuts. A close-up shows the nut being tightened.Step 30
When installing the drawers, first pull out the drawer guide rails attached to the cabinet and the drawer slides attached to the drawer box. Slide beads should also be pulled out.
Diagram shows the cabinet with drawer slides extended and a separate image of a drawer slide being pulled out. Arrows indicate the extension.Step 31
Insert the assembled drawers into the cabinet. If a large gap is found after installing the drawer, the slide rail can be moved up or down to adjust the gap.
Diagram shows drawers being inserted. Close-ups show how to adjust the drawer slides using screws to fine-tune the gap.Step 32
Attach the drawer fronts (labeled 'O' in this context, referring to the drawer face panels) to the drawer boxes using 'Fixing Clip & Screws' (7 ??).
Diagram shows drawer fronts being attached to the drawer boxes. A close-up shows the clip and screw mechanism.Step 33
Choose either Plan "A" or Plan "B" as needed. Attach the mirror frame (P) to the vanity top (A) using 'Screws' (8 ?).
Diagram shows two options, Plan A and Plan B, for attaching the mirror frame P to the vanity top A using screws.Step 34
Adjust the height of the vanity table by turning the hardware feet under the base to avoid imbalance and ensure the table is level.
Diagram shows the assembled vanity with an indication to adjust the feet. A close-up shows a foot with adjustment capability.Step 35
Position the vanity top (A) onto the cabinet (C, F). Secure it using 'Corner Codes' (9 ??) and 'Screws' (8 ?).
Diagram shows the vanity top being placed on the cabinet and then secured with corner brackets and screws. A close-up shows the corner code and screw assembly. The instruction "Adjust to the appropriate position and lock it" is present.Step 36
Install the 'Anti tipping hardware' (11 ?️) at the edge of the board as shown. This is to prevent insufficient length when connecting to the wall.
Diagram shows the anti-tipping strap being attached to the back of the vanity.Step 37
Install the 'Anti tipping hardware' (11 ?️) to secure the vanity to the wall. This involves drilling holes, using wall plugs, and screwing the hardware to both the wall and the furniture.
Diagram shows the process of wall mounting the anti-tipping hardware, including drilling, inserting wall plugs, and fastening.Step 38
Attach the mirror base (Q) to the mirror (B) using 'Screws' (8 ?).
Diagram shows the mirror B and its base Q being joined with screws. A close-up shows the screw insertion.Step 39
Attach the assembled mirror and base unit to the vanity top. Tear off the release paper and stick the 'Big Non-slip pads' (10 ?) onto the base of the mirror unit.
Diagram shows the mirror assembly being placed on the vanity top. A close-up shows the non-slip pads being applied to the bottom of the mirror base.Step 40
The mirror features integrated lighting with controls for 'Discoloration' (M), 'ON/OFF', and 'Brightness adjustment' (G).
Diagram shows the mirror with callouts pointing to the touch-sensitive controls and their functions.Step 41
Connect the 'AC/DC Adapter' (12V=3.0A) to the vanity's power input to activate the LED lighting and any other electronic features.
Diagram shows the AC/DC adapter being plugged into the vanity's power port. A close-up shows the adapter and connection.User's Guide: Intelligent Controller
Introduction
The intelligent controller box features 1 USB port and 1 Type-C port, capable of distributing current up to 5V DC-2A. It has two touch buttons for controlling light functions.
Operation
Light Button
Short touch: Turns lighting on, cycles through light colors, or turns lighting off.
Long touch: Adjusts the light luminance (brightness).
Induction Button
Short touch: Activates the induction function. The light turns on automatically when people are within 1 meter and powers off after 30 seconds of inactivity.
Long touch: Turns off the induction function.
Note: Activating the induction function may automatically turn off the light button modes. It is recommended to set light color and brightness before enabling induction.
Consumer Reminder: Wireless Charging
- This device supports wireless charging for mobile phones only. Attempting to charge other electronic devices may result in danger.
- Ensure no metal objects (including magnetic or metal phone cases) are placed between the phone and the wireless charger, as this can interfere with charging or cause hazardous conditions.
Attention Please
- If the device is unresponsive, unplug and re-plug the power to reset static electricity.
- If bubbles appear on the panel, remove the protective film.
- For any questions during installation, please contact customer support.
