INSTALLATION INSTRUCTIONS FOR SENSOR ACTIVATED ELECTRONIC SOAP DISPENSER

Model ESD-200

Deck Mounted, Plug-in Adapter Powered, Sensor Activated Electronic Soap Dispenser

Model ESD-250

Deck Mounted, Battery Powered, Sensor Activated Electronic Soap Dispenser

Model ESD-300

Deck Mounted, Plug-in Adapter Powered, Sensor Activated Electronic Soap Dispenser with Chrome Throat Plate

Model ESD-350

Deck Mounted, Battery Powered, Sensor Activated Electronic Soap Dispenser with Chrome Throat Plate

LIMITED WARRANTY

Sloan Valve Company warrants its ESD-200, ESD-250, ESD-300 and ESD-350 Electronic Soap Dispensers to be made of first class materials, free from defects of material or workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (1 year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer's cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company's products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries (Models ESD-250 and ESD-350). THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

For Soap Replenishment use:

• ESD-217 — 800 ml. bottle of Lotion Soap
• ESD-232 — 1600 ml. bottle of Lotion Soap
• ESD-231 — 800 ml. bottle of Anti-bacterial Soap
• ESD-233 — 1600 ml. bottle of Anti-bacterial Soap

Can also be used with TC® OneShot® Soap Cartridges (refer to Page 6 for TC Stock Numbers)

PRIOR TO INSTALLATION

New Soap Dispenser Installation:

• Locate position of soap dispenser using rough-in diagrams and template on Pages 2 and 3.
• Ensure that soap dispenser does not interfere with anything above or below the lavatory/counter top area (refer to Pages 2 and 3).
• Drill a 1" (25 mm) diameter hole in counter top (use template on Page 3).
• Clean area around hole.

Replacing Existing Soap Dispenser:

• Remove old components.
• Clean Area around hole.
• Ensure that hole is 15/16" to 1-1/4" diameter.

To order Replacement Soap Cartridges:

1-866-700-CLEAN (1-866-700-2532)

Or go to our website: www.optimasoap.com

Refills are also available through your local plumbing or janitorial supply distributor.

Please take the time to read this manual to ensure proper product installation and longevity. Also, please visit our website to download our most recent documentation for this product.

If you have questions about how to install your Sloan Flushometer, consult your local Sloan Representative or call Sloan Installation Engineering Department at: 1-888-SLOAN-14 (1-888-756-2614)

SOAP DISPENSER ROUGH-IN

Diagram Description: The rough-in diagram illustrates the dimensions for mounting the soap dispenser. Key dimensions include: spout width of 1-13/16" (46 mm), spout length of 5-3/8" (137 mm), and a required counter hole diameter of 1" (25 mm). It shows the brass shank, flange nut, sensor cord, and motor assembly. Clearance requirements are indicated, such as the 6-15/16" (176 mm) space needed for the motor assembly. A side view depicts the placement of the motor assembly and battery pack relative to the sink and counter, highlighting the need to avoid interference with water or drain lines.

INSTALLATION

The ESD-200/250/300/350 Soap Dispenser can often be mounted in the left or right hole of a 4" or 8" center-set sink. This is dependent on the faucet spout width and underside accessibility. If the motor and soap bottle interfere with water or drain lines, the dispenser must be installed through the countertop to the side of the sink.

Model ESD-20080/25085/30880/35187 Soap Dispenser and Faucet Combinations: When these ESD models are packaged with Sloan ETF-80, ETF-880, EBF-85, or EBF-187 Faucets for a 4" centerset sink, a special Trim Plate (ETF-299-A) is supplied. For these combinations, the faucet installs on the left and the soap dispenser on the right. Follow these instructions in conjunction with the faucet's installation instructions.

Water Supply Diagram: A diagram shows connections for HOT WATER SUPPLY and COLD WATER SUPPLY to a faucet, with the SOAP DISPENSER positioned nearby.

ESD-200, ESD-250, ESD-300 & ESD-350 Soap Dispenser Location Template

IMPORTANT: READ THIS BEFORE USING TEMPLATE.

If printing this document, ensure the template is the correct size. Measure the 1-1/2" (38 mm) dimension on the template to confirm accuracy. If it measures less than 1-1/2" (38 mm), reprint the page, ensuring "Shrinking oversized pages to paper size" or "Fit to page" options are unchecked in the printer settings.

Diagram Descriptions:

• "Soap Dispenser Mounted on Side of Sink": Shows a top-down view of a sink with a dispenser hole to the side.
• "ESD-20080/25085/30880/35187 Soap Dispenser/Faucet Combination Shown on a 4" Centerset Sink": Depicts a 4-inch centerset sink with a faucet and dispenser mounted side-by-side.

A 1" (25 mm) drill hole is indicated. The template also shows a "Center Drill Point" and a 1-1/2" (38 mm) dimension for verification. A "CUT HERE" line is shown for template use.

Plumbing Interference Note: Ensure the soap system does not interfere with the sink and plumbing under the counter.

1 - Install Spout

1. Slide Rubber Gasket onto Brass Shank, ensuring the hole in the Gasket is positioned over the Spring Pin in the Base of the Spout (where applicable).
2. Guide Brass Shank and Sensor Cord through the hole in the counter.
3. Position Spout to direct soap into the sink.
4. Guide Sensor Cord through the Flange Nut. Screw the Flange Nut onto the Brass Shank and tighten.

2 - Attach Motor Assembly

1. Slide C-clip to open position.
2. Place motor assembly at the bottom of the shank.
3. Rotate motor housing to avoid interference with the lavatory bottom and existing plumbing. Position the motor housing so the red reset button is accessible.
4. Push the motor assembly up into place and secure by pushing the C-clip closed.
5. Plug the sensor connector into the motor assembly and slide the rubber seal into place.

3 - Attach Battery Pack (Models ESD-250 & ESD-350 Only)

1. Place battery pack in a convenient location ensuring easy access.
2. Secure to wall with screws and anchors. Note: The battery pack may be mounted using one screw and anchor with the top slot facilitating easy removal for battery replacement. A foam gasket is applied to the back to seal screw holes.
3. Install 4 alkaline D-size batteries.
4. Connect the power cord from the battery pack by inserting then screwing clockwise into the inlet on top of the motor assembly.
5. A wall clip set may be used to hold the power cord against the wall.

4 - Connect AC Power (Models ESD-200 & ESD-300 Only)

1. Connect the power cord from the transformer by inserting then screwing clockwise into the inlet on top of the motor assembly. Note: Transformer is supplied with a 24" (610 mm) cord.
2. Plug transformer into a 120 VAC wall receptacle, activating the soap dispenser.
3. A wall clip set may be used to hold the power cord against the wall.

5 - Install Soap Cartridge

Important: DO NOT handle soap refill cartridge by tube. For proper operation, ensure that tubing is not loose or bent.

1. Unlock pump on refill cartridge by twisting counter-clockwise. The actuator will pop-up.
2. Guide refill tube up through the bottom of the motor assembly.
3. Lock soap refill into place by turning clockwise 1/4 turn.
4. Press the refill reset button. This will automatically prime the soap refill bottle and initiate the counting mechanism.

800 ml. refill cartridge dispenses up to 1000 hand washes (supplied).

1600 ml. refill cartridge dispenses up to 2000 hand washes.

When using a 1600 ml. refill cartridge, the dipswitch (located on the Motor behind the black grommet just above the Reset Button) must be in the Down Position.

Operation

As the user's hands enter the beam's effective range, the beam is reflected back into the sensor receiver and activates the solenoid valve, allowing a single soap application to flow from the spout.

• Flashing RED light ? in the sensor window indicates low refill.
• Flashing YELLOW light ? in the sensor window indicates low battery (Models ESD-250 & ESD-350 only).

CARE AND CLEANING OF...

...THE SOAP DISPENSER

Deactivate the soap dispenser by placing your fingers or thumb over the sensor area while you clean. The sensors are located in the upper right and upper left corners of the activation zone. Once dispenser is cleaned, remove fingers or thumb from the sensor area.

...CHROME AND SPECIAL FINISHES

DO NOT use abrasive or chemical cleaners (including chlorine bleach) to clean the spout, as this may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with a clean cloth or towel. While cleaning bathroom tile, protect the spout from any splattering of cleaner. Acids and cleaning fluids will discolor or remove chrome plating.

SOAP REPLACEMENT

When the Soap Bottle is empty, a new Bottle must be used. The Bottle furnished with the unit is not designed to be refilled. Altering the Bottle and refilling it with soap will void the warranty of the product.

To Order Replacement Soap Cartridges:

1-866-700-CLEAN (1-866-700-2532) or go to our website: www.optimasoap.com. Refills are also available through your local plumbing or janitorial supply distributor.

Soap Refill Cartridges Available:

• ESD-217 — 800 ml. bottle of Lotion Soap
• ESD-232 — 1600 ml. bottle of Lotion Soap
• ESD-231 — 800 ml. bottle of Anti-bacterial Soap
• ESD-233 — 1600 ml. bottle of Anti-bacterial Soap

Can also be replaced with TC® OneShot® Soap Bottles listed in the chart.

ATTENTION: Do not handle by tube. For proper operation, ensure that tubing is not loose or bent.

TROUBLESHOOTING GUIDE

1. Red LED light is flashing.
   • A. Refill bottle is low. Check the fill level and change as needed.
   • B. Reset button was not pressed after the refill was installed. Press and release reset button.
   • C. If reset button is held down more than one second, the red light will stay on. To turn the red light off, press the reset button quickly and the red light will go off.
2. Yellow LED light is flashing (Models ESD-250 & ESD-350 only).
   • A. Batteries are low. Replace with four (4) new D-size alkaline batteries.
3. Preventing soap from dispensing while cleaning.
   • A. Place your finger over the upper right hand or left hand corner of the sensor lens.
4. The dispenser does not activate properly when hand is placed under spout.
   • A. In restrooms with fluorescent lighting, lighting that may be dying out or not burning at full intensity will cause interference with the soap dispenser. Replace fluorescent tube(s) and the soap dispenser will then function normally. Cool, white tubes are recommended.
5. Soap does not dispense when user "waves" their hands under the spout.
   • A. Hands must be held “steady” under the spout for the dispenser to work.
6. Dispenser rotates due to users moving the spout.
   • A. Tighten the existing flange nut on the shaft of the spout under the counter.
   • B. If this problem continues, you can order a second “flange nut” (ESD-620) from Sloan Valve.
7. Soap does not dispense.
   • A. Check that your power source is plugged in correctly.
   • B. Make sure that batteries have been installed properly (Models ESD-250 & ESD-350 only).
   • C. Make sure the pump is open on the refill bottle (see Step 5).
8. Tube pulls out of the refill bottle.
   • A. The tubes have been “stitched” to prevent their removal, however please ensure that your housekeeping staff does not pick the bottle up or carry it by the tube.

When assistance is required, please contact Sloan Valve Company Installation Engineering Department at: 1-888-SLOAN-14 (1-888-756-2614)

PARTS LIST

The information contained in this document is subject to change without notice.

SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60131

Phone: 1-800-9-VALVE-9 or 1-847-671-4300 Fax: 1-800-447-8329 or 1-847-671-4380 www.sloanvalve.com

Copyright © 2010 SLOAN VALVE COMPANY

Code No: 0816549 Rev. 2 (08/10)