4-LEAF CLOVER-SHAPED GALVANIZED STEEL RAISED GARDEN BED
Assembly and Care Guide
Introduction
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell. Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty.
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email: customerservice@sunnydazedecor.com, or via our contact us page at https://tiny.cc/SunnydazeContact.
Review all care and assembly information carefully before using this product. Save this manual for future reference. Assemble components on a soft, clean surface to avoid damaging the finish.
Packaging Inspection: Inspect packaging to ensure all parts are accounted for before disposing of packing materials. Save the packing slip.
Parts List
The garden bed consists of the following parts:
| No. | Parts | Qty. |
|---|---|---|
| A | Side Panel (curved metal panel with pre-drilled holes) | 8 |
| B | Corner (angled metal connector piece) | 4 |
| C | M6x10mm Bolt | 60 |
| D | Wing Nut | 60 |
Visual Description of Parts:
- Part A: Eight identical curved metal panels that form the sides of the garden bed. Each panel has pre-drilled holes along its edges for assembly.
- Part B: Four angled metal pieces designed to connect the side panels at the corners. Each corner piece has pre-drilled holes.
- Part C: Sixty M6x10mm bolts used for fastening the panels together.
- Part D: Sixty wing nuts used to secure the bolts.
Tools Required (not included)
- ❌ Phillips Screwdriver
Safety Information
CAUTION: SHARP EDGES. USE EXTREME CAUTION. WEAR GLOVES DURING ASSEMBLY. ⚠️
WARNING: CHOKING HAZARD - This item contains small parts that can be swallowed. Keep children and pets away during assembly. ⚠️
Assembly Instructions
Helpful Hints:
- ? Do not tighten any bolts until the entire unit is loosely assembled. If hardware is tightened too soon, mounting holes may not align and parts may not easily fit together.
- ? Ensure panels are installed with the rolled edges facing the inside of the bed.
- ? Review all steps and understand assembly before beginning.
CAUTION: Sharp edges. Wear gloves during assembly. ⚠️
STEP 1: Assembling Side Panels
Parts needed: 8 x Side Panel (A), 20 x M6x10mm Bolt (C), 20 x Wing Nut (D)
Description: Align two Side Panels (A). Insert Bolt (C) through the outside edges of the panels and loosely secure by hand-tightening Wing Nuts (D). Repeat to connect three more sets of side panels, creating four pairs of joined panels.
Diagram shows four sets of two side panels being joined together using bolts and wing nuts.
STEP 2: Attaching Corners
Parts needed: 4 x Corner (B), 20 x M6x10mm Bolt (C), 20 x Wing Nut (D)
Description: Align one Corner (B) with the left side of one of the assembled panel sets. Insert Bolt (C) through the outside edges of the panels and loosely secure by hand-tightening Wing Nuts (D). Repeat to connect the three remaining corners to the side panel sets.
Diagram illustrates an angled corner piece (B) being attached to the ends of two joined side panels (A) using bolts (C) and wing nuts (D). This step is repeated for all four corners.
STEP 3: Final Assembly and Tightening
Parts needed: 20 x M6x10mm Bolt (C), 20 x Wing Nut (D)
Description: Align the four assembled sections and loosely fasten each section using the remaining Bolts (C) and Wing Nuts (D), as shown. After all sections have been loosely fastened, finish tightening all sixty sets of hardware.
Diagram shows the complete garden bed structure being formed by connecting the four sections and indicates the final tightening of all hardware.
Use & Care
- This garden bed provides ergonomic access to plants and can eliminate the need to till the soil each year as long as the soil is not packed down. Avoid stepping inside the bed!
- Prepare the site before installation. Level the ground and remove existing vegetation. Landscaping fabric can be used under the beds; a double layer is recommended for beds placed directly on a lawn.
- A layer of gravel or stone can be used at the bottom for improved drainage.
- Loosely hand-tighten all nuts and bolt sets first, position the bed, then tighten. After assembly, check that all fastening points are fully secured.
- Galvanized metal beds do not require maintenance and are built to withstand years of exposure to outdoor elements.
- The galvanized finish protects the steel from corrosion. Over time, galvanized steel will fade, and some discoloration is normal. Minor surface rust on edges and hardware is to be expected and should not affect the structural integrity of the product.
Safety Statements & Warnings
- Wear gloves during assembly to prevent personal injury.
- Do not stand on, or lean objects against the bed wall. Doing so may damage the product.
- Do not let children play in or around the garden bed.
- Using this item for applications other than gardening will void the product warranty.
Any modification to the product or failure to follow recommended care will void the product warranty.
If you experience issues with assembly or the product was damaged during shipping, please contact our customer service team through one of the methods mentioned at the top of page 1. Please have the item number and order information ready to expedite response time.
WARNING: Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, or neglect of this product. ⚠️
Contact Us – Sunnydaze Decor
