DELTACO EV CHARGER

Introduction

Thank you for choosing DELTACO!

Safety Instructions

Please follow the manual to use this device. Failure to follow instructions may result in danger to persons or damage to property.

1. You must also follow the documentation regarding charging of your electric vehicle.
2. May not operate if used on IT or other unearthed systems such as an isolated winding generator or isolating transformer.
3. Do not use this product if the cable, plug or this control box is damaged.
4. Use only for electric vehicle charging.
5. May only be used under the protection of residual-current circuit breaker.
6. The device contains no user-serviceable parts. Do not open up or modify any part of the device by yourself. Only authorized electricians with safe tools may perform maintenance.
7. If this product fails to operate correctly, stop using it. Instead contact the retailer where you bought the product or an authorized electrician or DELTACO's support.
8. Do not leave the charger unattended until it is in charging status.
9. Regularly check the charger for visible damages. Risk of electric shock when using a damaged charger.
10. Do not disconnect while the device is charging. Neither the vehicle plug nor the power plug may be disconnected while in use.
11. Protect this device from liquids/water, rain, wind, snow and sand, even if it is IP rated, safety first.
12. Do not immerse this product in water or other liquids.
13. Should not be used or stored or transported in extreme heat or extreme cold, please see operating and store temperatures.
14. Operating temperature min -25°C max +50°C ambient temperature. The ambient air should not contain acids or other corrosive or explosive gases.
15. This product should not be used in proximity of a strong magnetic field.
16. This product is expected to work normal at altitudes up to 2000 m. At higher altitudes the product might behave unexpected or there could be risk of electrical hazard.
17. Do not let the charger hang by the cable, the wear damage on the cable and the contacts can become considerable high since the cable and charger are heavy. Risk of electric shock, damage to property and injury to person. You must support the weight of the charger and cable in safe and stable way. For example, hang the charger on a hook, via the hang hole on the back of the product.
18. If you have the charger or cable on the ground, they can be easily damaged, keep them off the ground and protected from fall damage.
19. This product may cause a tripping hazard.
20. Old or erroneous contacts or cable line branches in the building can cause overheating at high loads, which in turn can be a fire risk. Because of this risk, let an authorized electrical installation company check the electrical installation.
21. The product shall be plugged directly to a power outlet without the use of an extension cable.
22. The product shall be connected without the use of an adapter.
23. This device must be earthed.

Diagrams and Indicators

The device features several indicators and a display for operation and status:

• 1. Button: Used to switch between charging current levels (6/8/10/13/16A) by pressing and holding, or to set a delayed start timer by a single press.
• 2. Charging Current (A): Displays the selected charging amperage.
• 3. Charging Time: Shows the duration of the charging session.
• 4. Charge Effect (kW/h): Displays the current charging power output.
• 5. Ready Indicator: An indicator showing the device is ready for use.
• 6. Vehicle Connected Indicator: Shows that the charger is connected to an electric vehicle.
• 7. Power Connected Indicator: Shows that the device is connected to the power supply.
• 8. Charging Status: Indicates the current status of the charging process (e.g., charging, preparing, fault).
• 9. Delayed Start Timer: Displays the set delay time before the charging process begins.

Diagrams illustrate the connection process: a hand plugging the Type 2 connector into the vehicle's charging port, showing the cable, control box, and the electric vehicle.

Usage

The control box should be hung up to reduce cable strain on the CEE 16A connector. It is recommended to hang the control box via the provided hook.

Connect the power plug to the power outlet (3-phase contact). The display and LEDs will turn on.

Press and hold the button to switch the charging current before connecting to your car. You can select between 6/8/10/13/16A.

A single press of the button allows you to set a delayed start timer from 30 minutes up to 10 hours. Each long press increases the timer duration by 30 minutes.

To restart the timer from zero, keep pressing the button until it reaches 0. To reset the timer completely, disconnect the cable from the power supply and reconnect it.

Connect the Type 2 plug to your electric vehicle. The charger will automatically detect the connection status and handshaking protocol and begin charging. Check the display to confirm charging is in progress.

Use Locations

Typical use locations for this product include sheltered places or areas with roofs, such as a garage or a parking lot with a roof.

Compatibility

The EV-3226 charger is compatible with all electric vehicles that have Type 2 connectors. Do not use it with other types of connectors.

LED Status

Note: If a timer is being set, one of the LEDs will be flashing. If the device is in reserved mode, LEDs will flash depending on the currently set current (e.g., the 3rd LED flashes with 6A).

Error Codes

If there is an ongoing fault, the display will indicate an error code.

• Display Code: 01 (Red LED flashes 1 time): Indicates current leakage; the residual current device (RCD) has activated. Solution: Power off the device and check the electric car and charger.
• Display Code: 02 (Red LED flashes 2 times): Indicates overcurrent protection activated. Solution: Power off the device and check the electric car.
• Display Code: 03 (Red LED flashes 3 times): Indicates earth fault protection activated. Solution: Power off the device and check the distribution grid.
• Display Code: 04 (Red LED flashes 4 times): Indicates overvoltage/undervoltage protection activated. Solution: Power off the device and check the distribution grid.
• Display Code: 05 (Red LED flashes 5 times): Indicates welding fault protection activated. Solution: Please contact DELTACO support.
• Display Code: 06 (Red LED flashes 6 times): Indicates communication error (between control box and car). Solution: Check if the connectors are tight. Try reconnecting the cables.

Electrical Protections

This product has built-in electrical protections. Please refer to the error codes for troubleshooting.

Self-Test

When this product starts up, it runs a self-test to ensure safety by checking its electrical protections. The display will turn on, and if the self-test is successful, it will remain on, indicating the device is ready. This process is automatic and requires no user action.

Cleaning

Disconnect the device from the power supply and use a dry cloth for cleaning. For stubborn stains, use a mild detergent with a damp cloth, then wipe dry.

Storage

Disconnect the cable from the power supply. It is recommended to clean the product if it has any stains before storage.

Support

More product information can be found at www.deltaco.eu.

Contact DELTACO via email: help@deltaco.eu.

Distributor Information

DistIT Services AB, Glasfibergatan 8, 125 45 Älvsjö, Sweden

DistIT Services AB, Suite 89, 95 Mortimer Street, London, W1W 7GB, England