FLEXISPOT

Specifications

Accessory Package

The following illustrations are for reference only, and may differ in appearance to the actual product. If you are missing any accessories or experience any installation issues, please contact customer service.

• Screws M6 (A): x8
• Screws M8 (B): x8
• Hex Wrench (C): x1
• Cable clamp (D): x2

Assembly Instructions

Step 1: Install the Tabletop and the Lifting Columns

Connect the tabletop (1) and the lifting columns (2) using screws (B) M8 and hex wrench (C).

Caution: Please do not place the glass surface directly on hard ground during installation, as it can be damaged by hard or sharp objects. Please be careful during installation to avoid dropping or breaking the glass.

Diagram Description: Shows the tabletop (labeled 1) being attached to two lifting columns (labeled 2) using screws (labeled B) and a hex wrench (labeled C). A close-up view illustrates screw B being inserted into a mounting point.

Step 2: Install Desk Feet

Install the feet (3) to the lifting columns with the screw M6 (A) and tighten it with hex wrench (C).

Caution: Please be careful during installation to avoid dropping or breaking the glass.

Diagram Description: Depicts the feet (labeled 3) being attached to the base of the lifting columns (labeled 2) using screws (labeled A) and the hex wrench (labeled C).

Step 3: Install the Motor and Power Lines

Connect the motor plug to the control box, then connect the corresponding side of the adapter plug to the adapter, and the other side to the wall socket. The motor and power lines can be managed with the included cable clamp.

Diagram Description: Illustrates the connection of the motor to the control box, and the power adapter to the control box and a wall outlet. A cable clamp is shown for organizing wires.

Keypad Instruction

The control panel features an LED screen, a Type-C port, two Type-A ports, a LOCK button, and adjustment buttons (up/down arrows) along with preset memory buttons (1-4).

Keypad Functions:

• Height Adjustment: Long press the up/down buttons to adjust the desk height. The screen displays "bot" at the lowest point and "top" at the highest point.
• Memory Presets: Buttons 1-4 are memory preset buttons. Hold down a number for 3 seconds to save the current height.
• Reset Procedure: If the desk malfunctions or an error code appears, press and hold buttons "3" and "4" together for 5 seconds to enter reset mode. The display shows "RST". Press and hold the "v" (down) key until the desk reaches its lowest point and rebounds slightly. The display will show "bot" upon completion.
• USB Ports: The desk is equipped with two Type-A ports and one Type-C port, supporting up to 18-watt charging per port (54-watt total when stationary). Charging stops when the desktop is moving and resumes after 5 seconds of inactivity.
• Child Lock: Press the "LOCK" button to enable the child lock function, disabling height adjustment. The display shows "Loc".
• Anti-Collision Sensitivity: Press and hold the "^" and "v" keys together for 5 seconds to cycle through 4 sensitivity levels (A-0: off, A-1: low, A-2: medium, A-3: high) to adjust anti-collision sensitivity.

Troubleshooting

Use the following tips to help detect and eliminate common errors. If your experienced issue is not listed, please contact your supplier. Do not attempt to investigate or correct these errors yourself.

Additional Troubleshooting Notes:

• If the display shows "RST", press and hold the "v" key until the desk reaches its lowest point and rebounds slightly. The display will show "bot" when reset is complete.
• If the display shows E01 or E02, let the desk idle for at least 18 minutes before operating again.
• For other codes or if the desk does not respond, ensure all cables are properly connected and undamaged. Unplug the desk for at least 10 seconds. Upon replugging, it should automatically enter reset mode.
• If issues persist, contact customer service.

Attention and Safety Precautions

• Power Supply: AC 100-240 V, 50/60Hz.
• Working Environment: 32° - 104° F.
• Cleaning: Unplug the power supply cable before cleaning. Use a slightly damp cloth to wipe away dust. Keep electrical components away from liquids and ensure connection lines are not damaged.
• Component Disposal: Electronic components, metal parts, plastic parts, and wires inside the control box must be disposed of according to local laws and regulations, not as household waste.
• Pre-Use: Ensure the product is installed correctly and read the instructions to understand all functions and settings before use.
• Supervision: Keep children away from electric height-adjustable desks, control units, and handsets. The manufacturer is not responsible for damages resulting from children's unpredictable behavior. Children or those with cognitive impairment should not use the product without supervision.
• Noise: Slight noise from the multi-wedge belt or brake system does not affect product use.
• Cleaning Solutions: Do not use corrosive or abrasive materials. Dispose of cleaning solutions in an environmentally friendly manner.
• Power Cord: If the power supply cord is damaged or broken, it must be replaced by the manufacturer or a qualified specialist to avoid injuries.
• Environment: Operate in a clean and safe environment. Be careful with packaging materials to avoid potential dangers like choking risks for children.
• Transportation: Retain the original package for future transportation if necessary.

Recycling and Disposal

This product cannot be disposed of as household waste. To prevent damage to the environment, this product should be recycled. Please use the relevant recycling systems available or contact the distributor or manufacturer for recycling assistance. ♻️