Taramps HD 3000 RGB Edition Amplifier
3000W RMS - 1 OHM / 2 OHMS / 4 OHMS
This manual provides instructions for the Taramps HD 3000 RGB Edition amplifier.
01. Term of Warranty
TARAMPS, located at Abilio Daguano Street 274, Res. Manoel Martins - Alfredo Marcondes, SP Brazil, ZIP CODE 19180-000, guarantees this product against any defects in project, making, assembling, and/or solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.
This warranty excludes:
- Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
- Tamper or torn warranty seal;
- Cases in which the product is not used in adequate conditions;
- Defects caused by accessories, modifications or features attached to the product;
- The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
- Warranty card is not properly filled or filled incorrectly;
- Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
- Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.
Technical Assistance
For international support, check on our website: www.taramps.com.br/en/rede-de-assistencias-tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br
02. Introduction
Read this manual before preparing the product. In case of doubt, contact our technical support: (18) 3266-4050 or www.taramps.com.br.
At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.
Declaration of Conformity
TARAMPS ELECTRONICS LTDA, Alfredo Marcondes - SP, Brazil, hereby declares that the product HD 3000 RGB complies with Directive 2014/30/EU, according to the harmonized standard EN 50498:2010 (Electromagnetic compatibility (EMC) Product family standard for aftermarket electronic equipment in vehicles). The full text of the EU Declaration of Conformity is available at the product's internet page.
Safety Requirements
CAUTION: To ensure proper use, please read through this manual before using the amplifier. It is specially important that you know the CAUTIONS contained here.
- The installation of this amplifier must be done by a qualified professional.
- Wear safety glasses, insulated gloves and correct tools for installing this product.
- This amplifier is for use with 12 V batteries. Always check the voltage before installing.
- This amplifier must be installed in a firm place with at least 1" (25 mm) space around the heatsink for proper heat spreading.
- Never install the amplifier in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of the vehicle.
- Be sure to install a protection fuse or a circuit breaker near the battery. Follow the ampere rating as indicated in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
- Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through the car's body.
- Before making any connection to the amplifier, disconnect the battery negative terminal.
- When in use, the external surface of the amplifier becomes hot. Avoid touching the heatsink area and keep children far from the amplifier.
- This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85 dB to prevent permanent hearing loss.
- Output connections for speakers may have voltage levels when the amplifier is operating. Make sure that the amplifier is turned OFF before proceeding with any connection or disconnection at these terminals.
- If you want to dispose of this amplifier, do not throw it in domestic waste. It must be collected by a used electronic product disposal service for proper recycling.
Safety Symbols
As you read this manual, pay attention to the safety symbols. This symbol with "CAUTION" is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.
Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.
03. Functions & Inputs
1 - INPUT (R and L): Signal inputs. Connect these signals to the head unit's RCA outputs. Use good quality shielded cables to avoid noise interference.
2 - GAIN: Adjusts the input sensitivity of the amplifier, allowing a perfect adjustment to the output signal levels of various head unit models on the market. It is possible to adjust from 4 V (minimum sensitivity) to 0.2 V (maximum sensitivity).
3 - CROSSOVER:
- HIGH PASS: Variable setting from 10 Hz to 80 Hz, which sets the beginning of the amplifier's frequency response.
- LOW PASS: Variable setting from 80 Hz to Full, which sets the end of the amplifier's operating frequency.
4 - BASS BOOST: BOOST: An extra 50 Hz boost for the bass with variable gain from 0 to +10 dB.
5 - MONITOR LEVEL REMOTE: Connection to an accessory that functions to control the gain and monitor the amplifier, displaying information from the indicator LEDs, such as distortion (CLIP/TEMP) and protection actuation (PROT), simultaneously. (Accessory not included).
LED Indicators & Protection System
| RGB LEDs | LED of Monitor | Conditions |
|---|---|---|
| Effect bars with the last schedule | Blue LED on | Working amplifier |
| Effect bars blink 2x in red | Red LED flashes 2x | Battery with voltage below 9 V |
| Effect bars flash 3x in red | Red LED flashes 3x | Battery with voltage above 16 V |
| Effect bars red continuously on | Red LED continuously on | Short circuit on output or between output terminal to GND |
| Effect bars flashing yellow 1 sec. lit 1 sec. wiped out | Yellow LED flashing 1 sec. on 1 sec. off | Temperature above operating limit (>85°C) |
04. Output & Power Supply Connector
1 - FAN: This amplifier has an internal fan. For optimal operation, the amplifier should be installed in a dry and ventilated place, with at least 1" (25 mm) free space on each side. The normal working temperature of this amplifier is 65°C.
CAUTION: The fan and ventilation openings are responsible for cooling the amplifier when it is in use. Do not obstruct them.
2 - SPEAKER: Output (positive and negative) for transducer connection (speakers). Follow the polarity described and the minimum impedance recommended. To combine speakers, the resulting impedance must be taken into consideration.
CAUTION: Due to the presence of voltage at the output terminals when the product is turned on, avoid contact with them. Risk of electric shock.
3 - POSITIVE POWER SUPPLY TERMINAL: Use a 4 AWG (21 mm²) cable directly from the positive terminal of the fused battery (150A), as close to the battery as possible.
4 - REMOTE TERMINAL: The remote wire must be connected to the remote terminal with a 0.75 mm² (18 AWG) cable.
5 - NEGATIVE POWER SUPPLY TERMINAL: A 4 AWG (21 mm²) cable, as short as possible, should be used, connected to the negative battery pole.
It is recommended that all cables have tinned ends to improve electrical contact.
Speaker Connection Examples:
Amplifier 1 OHM: Two 2 OHM speakers connected in parallel result in a 1 OHM impedance.
Amplifier 2 OHMS: Two 4 OHM speakers connected in parallel result in a 2 OHM impedance.
Amplifier 4 OHMS: Two 8 OHM speakers connected in parallel result in a 4 OHM impedance.
05. Color Effects
Color Palette (Configurable)
Changing Effects
- Quick click: Toggles the type of effect.
- Long click: Toggles the color palette of the selected effect, when configurable.
Types of Effects
| Effect Name | Configurable |
|---|---|
| VU-meter 1 | Yes |
| VU-meter 2 | Yes |
| VU-meter 3 | Yes |
| VU-meter 4 | Yes |
| Effects 1 | No |
| Effects 2 | No |
| Effects 3 | Yes |
| Effects 4 | Yes |
| Effects 5 | Yes |
| Effects 6 | No |
| Effects 7 | Yes |
| Effects 8 | Yes |
| Effects 9 | No |
| Effects 10 | No |
| Effects 11 | No |
| Effects 12 | No |
| Effects 13 | No |
| Flag 1 | No |
| Flag 2 | No |
| Flag 3 | No |
| Flag 4 | No |
The visual effects combined with the color palette settings allow for 108 possible combinations.
CAUTION: All connections to power supply, input and output connectors must be carried out only with the amplifier off.
06. Installation
Recommended Wire Gauge & Fuse
- Positive / negative power supply cable: 4 AWG
- Output cables wire gauge: 9 AWG
- Remote cable: 18 AWG
- Protection fuse or circuit breaker: 150A
These recommendations are calculated considering a maximum length of 4 m. For distances greater than this, you will need to increase the cable gauges.
CAUTION: Using wire gauges below the recommendation will result in power loss and overheating of wiring.
Check polarity and never reverse power supply cables due to the risk of damage to the amplifier. It is compulsory to install protection fuses or circuit breakers as close as possible to the batteries.
Required battery bank capacity: At least 150Ah.
CAUTION: This equipment is not suitable for use in places where children may be present.
Wiring Diagram
A diagram shows the connection of two speakers to the amplifier's speaker outputs using 6mm² (9 AWG) cables. The positive terminals of the speakers connect to the amplifier's positive output, and the negative terminals connect to the negative output. A note indicates that for compression drivers and tweeters, a passive filter must be installed in the positive terminal of the same ones (consult the transducer's manufacturer manual).
The diagram also shows the connection of the amplifier's power terminals to two batteries. The positive power terminal connects to the positive battery terminal via a circuit breaker and a 21mm² (4 AWG) cable. The negative power terminal connects to the negative battery pole via a 21mm² (4 AWG) cable. The remote terminal connects to the head unit's remote output with a 0.75mm² (18 AWG) cable.
A RCA cable connects the head unit's audio output to the amplifier's input.
A caution note states: "The entire aluminum surface of the amplifier acts as a heat sink. The usual working temperature is 65°C. So, avoid contact with this surface when the amplifier is in use."
07. Technical Features
| Parameter | 1 Ohm | 2 Ohms | 4 Ohms |
|---|---|---|---|
| Output Impedance Range: | 1 Ohm | 2 Ohms | 4 Ohms |
| Number of Channels: | 01 | ||
| Output Power @12.6 VDC*: | |||
| 1 OHM: | 3000 W RMS | ||
| 2 OHMS: | 2025 W RMS | 3000 W RMS | |
| 4 OHMS: | 2025 W RMS | 3000 W RMS | |
| 8 OHMS: | 2025 W RMS | ||
| Input Sensitivity: | 0.22 V ~ 4 V | ||
| Signal-to-noise Ratio: | >89 dB | ||
| Frequency Response: | 10 Hz ~ 20 KHz (-3 dB)** | ||
| Crossover: | |||
| HPF (High Pass Filter): | 10 Hz ~ 80 Hz (-12 dB/8th) Variable | ||
| LPF (Low Pass Filter): | 80 Hz ~ Full (-12 dB/8th) Variable | ||
| Bass Boost: | 0 ~ 10 dB (50 Hz) | ||
| Input Impedance: | 10 K Ohms | ||
| Protection System: | Short-circuit between speaker output, short-circuit between GND and any speaker output, low impedance at output, low/high battery supply voltage and thermal protection. | ||
| Minimum Supply Voltage: | 9 VDC | ||
| Maximum Supply Voltage: | 16 VDC | ||
| Idle Consumption***: | 1.50 A | 1.60 A | 1.90 A |
| Musical Consumption @12.6 VDC: | 153 A | 152 A | 149 A |
| Rated Power Consumption: | 306 A | 304 A | 298 A |
| Dimensions (W x H x L): | 229 x 65 x 186 mm (9.01" x 2.56" x 7.32") | ||
| Weight: | 2.40 Kg (5.28 lb) | ||
*Rated power with 1 KHz sinusoidal signal and THD <=10%, with resistive loads, measured with Audio Precision APx525 audio analyzer or equivalent and the product at lower than 50°C case temperature and 12.6 V supply voltage.
**Frequency response measured at twice the minimum impedance.
*** Amplifier consumption may vary depending on the effect used in the RGB LED. The value mentioned above is with the RGB LEDs turned off. The values as above are typical and may vary, due to electronic components tolerance or manufacturing process.
For further information or questions, visit our website or contact TARAMPS support.
Manufactured by: TARAMPS ELECTRONICS LTDA, TAX ID: 11.273.485/0001-03, Address: 30 Julio Budisk Highway, Alfredo Marcondes - SP, Made in Brazil.
Website: www.taramps.com.br
