Introduction
Read this manual carefully before connecting or using the product. For any doubts, please contact our technical support at (18) 3266-4050 or visit www.taramps.com.br.
Environmental Disposal: At the end of its useful life, this product must not be disposed of in household waste. Please take it to an electronic equipment collection or recycling center for proper disposal.
Declaration of Conformity
CE Mark
TARAMPS ELECTRONICS LTDA, Alfredo Marcondes - SP, Brazil, hereby declares that the product BASS 30K complies with Directive 2014/30/EU, according to the harmonized standard EN 50498:2010 (Electromagnetic compatibility - EMC) for aftermarket electronic equipment in vehicles. The full text of the EU Declaration of Conformity is available on the product's internet page.
Safety Requirements
To ensure proper use, read this manual thoroughly before operating the amplifier. It is crucial to understand the WARNINGS and CAUTIONS provided.
- Installation must be performed by a qualified professional.
- Use safety glasses, insulated gloves, and appropriate tools during installation.
- This amplifier is designed for use with 12V batteries. Always verify the voltage before installation.
- Install the amplifier in a firm location, ensuring at least 1" (25mm) of space around the heatsink for adequate heat dissipation.
- Never install the amplifier in areas exposed to dust, humidity, or water. Ensure it is placed away from fuel tanks, fuel lines, heat sources, and other vehicle components.
- Install a protection fuse or circuit breaker near the battery, matching the amperage specified in this manual. Using an incorrect fuse or breaker can lead to overheating, smoke, product damage, or personal injury.
- Avoid routing wires over or through sharp edges. Use rubber or plastic grommets to protect any wires passing through the vehicle's bodywork.
- Before making any connections to the amplifier, disconnect the negative (-) terminal of the vehicle battery.
- The amplifier's external surface may become hot during operation. Avoid touching the heatsink area and keep children away from the unit.
- This amplifier can produce high sound pressure levels. Avoid continuous exposure to levels exceeding 85dB to prevent permanent hearing loss.
- Speaker output connections may carry voltage when the amplifier is operating. Ensure the amplifier is turned OFF before connecting or disconnecting any speaker terminals.
- If you need to dispose of this amplifier, do not discard it with regular household waste. It must be collected by a specialized electronic product disposal service for proper recycling.
⚠️ CAUTION: This symbol alerts users to important instructions. Failure to follow these instructions may result in risks to the user or damage to the product.
Taramps reserves the right to modify the contents of this manual at any time without prior notice and is not obligated to apply such changes to previously produced units.
Functions, Inputs & Outputs
Diagram Description (Rear Panel): The rear panel of the BASS 30K amplifier features several connection points:
- 1. INPUT: Audio signal input. Connect to the RCA outputs of your CD/DVD Player using good quality shielded cables to prevent noise interference.
- 2. THRU OUT: This output can send the same input signal (INPUT) to another amplifier.
- 3. LEVEL: Adjusts the amplifier's input sensitivity, allowing for optimal matching with the output signal levels of most CD/DVD Players.
- 4. SUBSONIC: Variable adjustment from 8Hz to 30Hz, determining the start of the amplifier's operating frequency range.
- 5. LOW PASS: Variable adjustment from 60Hz to 250Hz, determining the end of the amplifier's operating frequency range.
- 6. FREQ.: Sets the center frequency for the Bass Boost feature, adjustable from 35Hz to 60Hz.
- 7. BASS BOOST: Provides reinforcement for sub-bass frequencies, with a variable gain range from 0 to +12dB.
- 8. REMOTE TERMINAL: Connect this to the CD/DVD Player's remote output using a 0.75 mm² (18 AWG) cable.
- 9. SPEAKER: Output terminals (positive and negative) for connecting loudspeakers. Follow the indicated polarity and the minimum recommended impedance. When combining loudspeakers, the resulting impedance must be considered.
Diagram Description (Speaker Impedance): Illustrates two 2 OHM speakers connected in parallel, resulting in a total impedance of 1 OHM.
⚠️ CAUTION: Due to the presence of voltage at the output terminals when the product is ON, avoid contact. Risk of electric shock.
- 10. COOLERS (Fans): The BASS 30K is equipped with four internal ventilation fans. These must not be obstructed. For optimal performance, install the amplifier in a cool and well-ventilated location. It is recommended not to embed the unit, allowing air to circulate freely throughout its interior to prevent thermal protection from activating.
⚠️ CAUTION: The fans and ventilation openings are essential for cooling the amplifier during use and must not be obstructed.
Power Supply Connector
Diagram Description (Power Terminals): The amplifier features two main power terminals.
- 1. NEGATIVE POWER SUPPLY TERMINAL: Use a 2 x 70mm² (2/0 AWG) cable, as short as possible, connected to the negative battery pole.
- 2. POSITIVE POWER SUPPLY TERMINAL: Use a 2 x 70mm² (2/0 AWG) cable directly from the positive battery terminal. Install a fuse (1160A) as close to the battery as possible.
Recommendation: It is advised that all cable ends be tinned to ensure better electrical contact. Utilize all available power inputs.
⚠️ CAUTION: Before making any connections to the power terminals, ensure the vehicle battery's negative (-) terminal is disconnected.
LED Indicators & Protection System
- ON (BLUE LED): Indicates that the amplifier is powered on.
- CLIP (YELLOW LED): Indicates the amplifier is operating at the threshold of distortion or excessive temperature. If the red LED also blinks, it signifies excessive distortion.
- PROT (RED LED): Indicates a short circuit at the amplifier's output or an impedance lower than the equipment can tolerate. It also indicates if the supply voltage is below 9V or above 17V.
Protection Systems:
- SHORT-CIRCUIT PROTECTION: Shuts down the audio output if a short circuit or impedance lower than supported is detected at the output.
- THERMAL PROTECTION: Activates when the amplifier reaches a high internal temperature. Audio output is interrupted, the yellow LED flashes continuously, and the internal fans remain on until the temperature returns to normal operating levels. Do not turn off the amplifier during this condition to allow for faster cooling.
- HIGH/LOW SUPPLY VOLTAGE: If the supply voltage drops below 9V, the PROT (RED) LED will flash 2 times intermittently. If the voltage exceeds 17V, the PROT (RED) LED will flash 3 times intermittently. The protection system will trigger, cutting off the audio signal. The amplifier will only resume normal operation after being switched off and then on again, provided the supply voltage is between 9V and 17V.
Installation
⚠️ CAUTION: All connections to power supply, input, and output connectors must be carried out only when the amplifier is OFF.
Recommended Wire Gauge & Fuse
| Component | Specification |
|---|---|
| Positive/Negative Power Supply Cable | 2 x 70mm² (2/0 AWG) |
| Output Cables Wire Gauge | 10mm² (7 AWG) |
| Remote Cable | 0.75mm² (18 AWG) |
| Protection Fuse or Circuit Breaker | 1160A |
These specifications are calculated considering a maximum cable length of 4m. For distances greater than this, you will need to increase the cable gauges.
⚠️ CAUTION: Using wire gauges below the recommendation will result in power loss and overheating of the wiring.
⚠️ CAUTION: Check polarity and never reverse power supply cables due to the risk of damage to the amplifier. It is compulsory to install protection fuses or circuit breakers as close as possible to the batteries.
Diagram Description (Wiring Example): The diagram illustrates a typical installation setup:
- Two Taramps amplifiers are shown.
- A battery bank (multiple batteries) is depicted, with positive (+) and negative (GND) terminals.
- Two 70mm² (2/0 AWG) cables connect from the battery bank's positive terminal to each amplifier's positive power input. A circuit breaker is shown on the positive line near the battery.
- Two 70mm² (2/0 AWG) cables connect from the battery bank's negative terminal (GND) to each amplifier's negative power input.
- RCA cables connect from a "Head Unit" (e.g., car stereo) to the "INPUT" terminals of the amplifiers.
- Remote cables (0.75mm² / 18 AWG) connect from the "Head Unit" to the "REMOTE" terminals of the amplifiers.
- Speaker cables (10mm² / 7 AWG) connect from the "SPEAKER" terminals of the amplifiers to loudspeakers.
- A "Second Amplifier" is shown, suggesting a multi-amplifier setup.
Note: Required battery bank capacity: At least 1160Ah.
⚠️ CAUTION: The entire aluminum surface of the amplifier serves as a heatsink. The usual working temperature is 65°C. Avoid contact with this surface when the amplifier is in use.
⚠️ CAUTION: This equipment is not suitable for use in places where children may be present.
Technical Features
| Feature | Specification |
|---|---|
| Minimum Output Impedance | 1 Ohm |
| Number of Channels | 01 |
| Output Power @14.4VDC | 1 OHM: 30000W RMS* 2 OHMS: 17010W RMS |
| Input Sensitivity (Level 100%) | 400mV |
| Signal-to-noise Ratio | >90dB |
| Frequency Response (Full Range) | 8Hz ~ 250Hz (-3dB) |
| Crossover | HPF (Subsonic Filter): 8Hz ~ 30Hz (-12dB/8a) Variable LPF (Low Pass Filter): 60Hz ~ 250Hz (-12dB/8a) Variable |
| Bass Boost | Freq.: 35Hz ~ 60Hz Boost: 0 ~ 12dB |
| Efficiency | 90% |
| Input Impedance | 22K Ohms |
| Protection System | Short-Circuit to Output, Short on output to GND, Low impedance at output, low/high supply voltage, and Thermal protection. |
| Minimum Supply Voltage | 9VDC |
| Maximum Supply Voltage | 17VDC |
| Idle Consumption | 400mA |
| Musical Consumption @14.4VDC | 1156A |
| Rated Power Consumption | 2312A |
| Dimensions (W x H x L) | 239 x 73 x 1044mm (9.41" x 2.87" x 41.10") |
| Weight | 19.20Kg (42.24lb) |
*Output power measured at 60Hz, nominal impedance, THD <= 10% and battery voltage = 14.4VDC. The values provided are typical and may vary due to electronic component tolerances or manufacturing processes. For further information or questions, visit our website or contact TARAMPS support.
Warranty & Technical Assistance
Term of Warranty
TARAMPS, located at Rua Abílio Daguano, 274, Res. Manoel Martins – Alfredo Marcondes, SP - Brazil, ZIP CODE 19180-000, guarantees this product against any defects in project, manufacturing, assembly, or solidarity due to design flaws that render it improper or inadequate for its intended use, for a period of 12 months from the date of purchase. In case of a defect during the warranty period, TARAMPS' responsibility is limited to the repair or substitution of the device of its own manufacture.
This warranty excludes:
- Products damaged by incorrect installation, water infiltration, or violation by unauthorized individuals.
- Tampered or torn warranty seals.
- Cases where the product is not used under normal conditions.
- Defects caused by accessories, modifications, or equipment attached to the product.
- Product damage resulting from falls, impacts, or natural events (flooding, lightning, etc.).
- Warranty cards that are not properly filled out or are torn.
- Costs associated with equipment uninstallation, reinstallation, and shipment to the technical assistance center.
- Any damages resulting from product problems or losses caused by discontinued use of the product.
Technical Assistance
Taramps Electronics has a network of Technical Assistance centers throughout Brazil and is ready to assist with your queries and needs. To locate a Taramps Electronics Technical Assistance center near you, please visit our website: www.taramps.com.br/pt/rede-de-assistencias-tecnicas. Alternatively, contact the factory's technical assistance department:
Taramps Electronics
Rua: Abílio Daguano, n° 274
CEP: 19.180-000
Phones: (18) 3266-4050 / +55 18 99749-3391
E-mail: angelo.assistencia@taramps.com.br (for Brazil) / service@taramps.com.br (for international support)
Manufacturer Information
Manufactured by: TARAMPS ELECTRONICS LTDA
CNPJ/TAX ID: 11.273.485/0001-03
Address: R. João Silvério, 121 • Res. Manoel Martins, Alfredo Marcondes - SP, Brazil.
Website: www.taramps.com.br
Taramps
