First Time Setup: Bluetooth Pairing
Follow these steps to pair your JLab Epic Executive earbuds with your device.
Step 1: Enable Bluetooth
Turn on Bluetooth in your device's settings.
[Illustration: Smartphone screen showing Bluetooth settings with Bluetooth toggled ON.]
Step 2: Enter Pairing Mode
Press and hold the button on the earbud for 10 seconds. Release. The indicator light will flash red and blue, indicating pairing mode.
[Illustration: Earbud with a button. Diagram shows the button being pressed for 10 seconds. Indicator light shown flashing red and blue.]
Step 3: Connect to Your Device
In your device's Bluetooth settings, select 'JLab Epic' to connect. When Bluetooth pairing is successful, the indicator light will slowly flash blue.
[Illustration: Smartphone screen showing Bluetooth settings, with 'JLab Epic' selected and connecting. Earbud indicator light shown slowly flashing blue.]
Frequent Use: Once the JLab Epic Executive is paired with your device, the earbuds will automatically connect to your Bluetooth device upon powering on.
Button Functions
- Power On/Off: Long press for 3 seconds.
- Bluetooth Pairing: Long press for 10 seconds (refer to First Time Setup: Bluetooth Pairing instructions).
- Play/Pause/Answer/End Call: Short press.
- Activate Siri (iOS) or "OK Google" (ANDROID): Double tap.
- Volume Down: Short press.
- Previous Track: Long press for 2 seconds.
- Volume Up: Short press.
- Next Track: Long press for 2 seconds.
Voice Prompts
- Power On: Beep.
- Bluetooth Connected: Two beeps.
- Low Battery: "Low Battery" (below 20%).
- Power Off: Beep.
Noise Cancellation Function
- Turn On/Off: Short press (Green light illuminates when active).
- Note: Be sure to turn off noise cancellation when not in use.
Charging
Step 1: Connect to Power
Insert the USB cable into a charging source and connect the Micro USB to the JLab Epic Executive port to charge.
[Illustration: USB cable connected to a charging source (e.g., wall adapter, computer) and the Micro USB end plugged into the JLab Epic Executive earbud.]
Charging Indicator:
The indicator light will be solid red while charging and turn blue when fully charged.
[Illustration: Earbud showing a solid red light (charging) and another showing a solid blue light (fully charged).]
Accessories
Proper fit is essential for optimal sound and comfort.
Ear Tips and Cush Fins
Cush Fin for secure fit: Rotate the Cush Fins to your desired position. Move the ear tips to your desired position.
[Illustration: Earbud with Cush Fin and ear tip. Arrows indicate rotating the Cush Fin and moving the ear tip.]
ATP (Adjustable Ear Tip Placement)
Position 1: Comfortable, deeper fit.
Position 2: Looser, shallower fit.
[Illustration: Two diagrams showing ear tips placed at different depths within the ear canal.]
Finding the Best Fit
Try various ear tips and Cush Fins to find the best fit for your ears.
Wearing the Earbuds
- Place the cable behind your neck, laying both sides parallel.
- Press the cable into the channel for a custom fit.
[Illustration: Person wearing earbuds with the cable routed behind the neck and secured.]
Using the AUX Adapter
Connect the Adapter
Insert the USB cable into the JLab Epic Executive and connect the AUX adapter to USB.
[Illustration: USB cable from earbud connected to AUX adapter.]
Play Audio
Play audio from airplane or mobile device AUX. This allows for wired playback without power.
[Illustration: AUX adapter plugged into an airplane seat audio jack and a mobile device's headphone jack.]
Troubleshooting Connection Issues
Cannot see JLAB EPIC on my device
- Turn off Bluetooth, then turn it back on in your device settings.
- If you still don't see JLab Epic, repeat First Time Setup: Bluetooth Pairing.
JLAB EPIC not reconnecting to my device after powering on
- In your device settings, skip JLab Epic.
- Turn off Bluetooth, then turn it back on in your device settings.
- Repeat First Time Setup: Bluetooth Pairing.
Bluetooth is connecting to an unwanted device
Note: JLab Epic Executive can remember up to 8 devices. It will try to automatically connect to the last used device.
- If you have multiple devices connected to JLab Epic Executive, turn off Bluetooth on the unwanted device and turn on Bluetooth on the desired device.
- Long press the button for 10 seconds. Release. The indicator light will flash red and blue, indicating pairing mode. Select 'JLab Epic' in your device settings to connect. The indicator light will slowly flash blue when Bluetooth pairing.
Warnings and Precautions
Safety
- Ensure the USB port is closed and secured. This prevents sweat and water damage.
- Before charging, the JLab Epic Executive earbuds must be completely dry. Internal components may be damaged if exposed to moisture. Allow to air dry before charging.
- [Illustration: USB port with a red cross over water droplets, indicating protection from water. Another illustration shows an earbud air drying.]
General Precautions
- Avoid getting water or liquid into the earbud ear tips or charging port.
- Avoid extreme heat, cold, and humidity.
- Avoid dropping or crushing the earbuds, yanking the cable with quick tugs, or bending the cable at sharp angles.
- Earwax may build up in the earbud ear tips, reducing sound quality. Clean earwax carefully with a cotton swab or other small tool to improve sound quality.
- If you experience discomfort or pain, try lowering the volume or temporarily stopping use.
- If you experience regular discomfort while using this product, stop use and consult your doctor.
- Treat your earbuds with care, similar to a pair of stylish sunglasses, and store them in a safe place when not in use.
JLab Audio App
Enhance your JLab Audio experience with the Burn-in Tool and product notifications.
Visit us online: INTL.JLABAUDIO.COM
