MICROTECH Digital Micrometer IP65 User Manual and Specifications

Product Overview

This document provides the user manual and technical specifications for the MICROTECH Digital Micrometer IP65. It details the product's features, operation, and important safety information. The micrometer is designed for precise measurements and meets IP65 protection standards. It is manufactured by MICROTECH, an innovator in measuring instruments, and is compliant with ISO 17025 and ISO 9001 standards.

Key features include:

IP65 Protection: Dust-tight and protected against water jets.
ISO 17025 Calibration: Indicates adherence to calibration and testing laboratory standards.
Hold Function: Allows holding the measured value.
Friction Thimble: For smooth and controlled spindle movement.
Resolution: 1µm (0.001 mm).

Specifications

Item No	Range (mm/inch)	Resolution (mm)	Accuracy (μm)	Dimensions (mm)				Micrometer Head	Protection Class
				C	L	B	D
110180254	0-25 / 0-1"	0.001	±2	24	32	7	2	friction	IP65
110180504	25-50 / 1-2"	0.001	±2	33	56	8	2	friction	IP65
110180754	50-75 / 2-3"	0.001	±2	48	85	12	2	friction	IP65
110181004	75-100 / 3-4"	0.001	±3	60	112	12	2	friction	IP65
110181254	100-125 / 4-5"	0.001	±4	73	135	14	2		IP65
110181504	125-150 / 5-6"	0.001	±4	86	160	16	2		IP65
110180514	0-50 / 0-2" (Double Range)	0.001	±3	33	56	8	2	friction	IP65
110181014	50-100 / 2-4" (Double Range)	0.001	±4	60	112	12	2	friction	IP65

Diagram Description: A line drawing illustrates the digital micrometer. Key dimensions are labeled: L (length), B (width), D (depth), and a circular measurement point with diameter indicated as Ø6.5. The main body of the micrometer shows the digital display, control buttons (SET, UNIT, 0/MODE), and the measuring spindle.

Functions

SET: Resets the zero point in absolute measurements.
0/MODE: Switches the device on. Allows switching between absolute and relative measurement modes. Resets zero in relative measurements.
HOLD: Holds the measured value. Can also be used to output measurement results to an external socket (details not specified).
UNIT: Switches between metric and English measurement systems. A long press turns the device off.

Operation

Clean the oil from the measuring surfaces of the micrometer with a cloth.
If necessary, open the battery cover and insert the battery (type CR2032), observing the correct polarity. Blinking display information or absence of display suggests battery replacement. After battery replacement, press the SET button to set the zero point to 0.000.
Turn on the display by pressing the 0/MODE button.
Verify the display is set to zero. Bring the measuring surfaces of the anvil and spindle into contact (or use a setting gauge), utilize the ratchet, and take a measurement. Rotate the micrometer screw in the direction of convergence using the ratchet. Note: A hole located at the end of the screw is used only for the reverse spindle.
For zero setting, press and hold the O/MODE or SET button to reset to Zero.
After switching on, the display shows the measured value in the selected metric or English system of units. Press the UNIT button to switch between these systems.
The display shows measurements in absolute or relative terms. Press the 0/MODE button to switch between absolute and relative measurement modes.
During measurement, the thimble should rotate only by the ratchet. Ensure the workpiece is in firm contact with the measuring surfaces of the micrometer, engaging the ratchet 2-3 times. Avoid warping the measuring surfaces.
This micrometer features an auto switch-off function after 10 minutes of non-use. To switch off manually, press and hold the UNIT button for 2 seconds.
After use, wipe the measuring surfaces of the micrometer with a cloth and apply anticorrosive oil.

WARNING!

Avoid contact between the micrometer's body electronics and emulsions or oils.
During measurements, periodically check the micrometer's zero setting.
Do not rotate the micrometer screw using the thimble when the measuring surfaces are close together.
Avoid shocks or dropping the micrometer, even from a small height.
Do not disassemble or adjust the micrometer unless you are a qualified service person.

Contact Information

MICROTECH
Innovative measuring instruments
61001, Kharkiv, Ukraine, str. Rustaveli, 39
Tel: +38 (057) 739-03-50
Website: www.microtech.ua
Email: tool@microtech.ua

Note: Information subject to change without prior notice.

	Microtech Cable Crimping Digital Micrometer IP65 User Manual User manual for the Microtech Cable Crimping Digital Micrometer IP65, detailing specifications, functions, operation, and safety warnings for accurate measurements.
	Microtech Outside Point Digital Caliper User Manual - Specifications and Operation User manual for the Microtech Outside Point Digital Caliper (Model 141403141). Includes specifications, button functions, operation instructions, and safety warnings for accurate measurements.
	Microtech Computerized Height Gauge User Manual - Precision Measurement Comprehensive user manual for Microtech's Computerized Height Gauges, detailing specifications, functions, operation, and connectivity for accurate industrial measurements.
	Microtech Sub-Micron Bench Tablet Micrometer User Manual - Precision Measurement Official user manual for the Microtech Sub-Micron Bench Tablet Micrometer. Details specifications, technical data, operation, data transfer (USB, Wireless HID), functions, and industry 4.0 applications for precision measurement.
	Microtech Wireless Caliper IP67 User Manual - Features, Specifications, and Operation Comprehensive user manual for the Microtech Wireless Caliper IP67. Learn about its features, specifications, data transfer modes, operation, and maintenance. Includes model numbers, dimensions, and connectivity options.
	Microtech Horizontal Indicator Calibration Stand - Precision Measurement Discover the Microtech Horizontal Indicator Calibration Stand, designed for accurate calibration of dial and digital indicators with 0.01mm resolution. Features include multiple measurement modes, extensive memory management, and versatile data transfer options like Wireless and USB HID, supported by an ISO17025 accredited calibration certificate.
	Microtech Sub-Micron Intelligent Computerized Indicator User Manual User manual for the Microtech Sub-Micron Intelligent Computerized Indicator, detailing specifications, functions, data transfer, and operation. Includes technical data, operational guides, and product features.
	Microtech Force Calipers: IP67 Double Force & IP54 Precision Models Discover Microtech's advanced digital calipers, featuring the IP67 Double Force model with dual force control and waterproof design, and the IP54 Precision model for accurate measurements. Both offer high precision and calibration certificates.

MICROTECH Digital Micrometer IP65