VIZIO JV50P 10A HDTV QUICKSTART GUIDE

Before You Begin

• Verify all of the contents of your accessory package.
• Review safety guidelines in the Owner's Manual.
• Place the HDTV so the rear connectors are accessible.
• Install ? AA Batteries into the VIZIO Remote Control ⚙️.
• Write down your JV50P Serial Number (located on the back).

Contents

• ? 2 Power Cords
• VIZIO JV50P User Manual, Warranty & Repair Info, VIP Brochure and Registration Card.
• ⚙️ Remote Control (Includes 2 AA Batteries)
• ? AV Cable

Connecting Your VIZIO JV50P HDTV

The Best Connection

For the best quality picture, VIZIO recommends using HDMI, DTV, RGB, or Component inputs when possible. These are the only inputs capable of high definition (HD). Using these inputs does not guarantee high definition unless a high definition source is connected. However, not all equipment is capable of these connections. TV, AV, and S-Video are not capable of HD signals.

Note: Both DTV and TV share the same port. The television will automatically register which input type is connected.

Four Easy Steps to Connect Your Equipment

Simply follow our color-coded Step Charts and you're done.

Step 1: Choose Items to Connect to your JV50P

Determine which type of Signal Source and any Additional Equipment you wish to connect to your JV50P. The colored dots under each Signal Source and Additional Equipment indicate which type of connections you may use to connect to your JV50P. For example, a red dot indicates a connection that uses red RCA cables.

Step 2: Choose Equipment Connection Methods

Using the colored dots from Step One, follow the row across to Step Two to match up the colored dots to the same colored connection method. Choose ONLY one method for each piece of equipment.

Step 3: Select Cables and Make Connections

Once you have determined the connection methods from Step Two, follow the row to Step Three to determine what kind of cables you need and what the connections look like on your equipment. Following the color-coded system, use the appropriate cables and connect your Signal Source and Additional Equipment to the color-coded inputs on your JV50P. Once connected, turn on your JV50P and all your equipment.

Step 4: Use Your JV50P

Fill in the Connection Reference Chart below, noting how you will connect your equipment/signal source to your JV50P. If you are using the DTV/TV input, consult your Owner's Manual for programming instructions. Press the [INPUT Button] on your remote. The INPUT menu will appear. Continue pressing the [INPUT Button] until you reach the corresponding connection.

Connection Reference

The following table details the available connections on your JV50P, the type of signal they support, and the required cables.

* Component cables also include stereo RCA cables for audio. HDMI, DVI-HDMI, VGA, Audio mini-jack, and Component cables are not included and are available at www.VIZIO.com.

** Optical audio cable is not included.

For help with connecting components to your VIZIO TV, visit http://ceaconnectionsguide.com/ for an interactive guide.

3 Ways to Get HDTV

• 1) Off-Air Antenna: Use the DTV antenna input. To see if you are able to receive HD signals off-air and for help choosing the right antenna, visit www.antennaweb.org.
• 2) Cable: Subscribe to HD programming through your local cable company (HD cable box required).
• 3) Satellite: Subscribe to HD programming through Direct TV or Dish Network (HD satellite receiver required).

Programming Your TV

Initial Setup (Two Steps)

Programming your JV50P is a simple TWO STEP process. All you need is your Remote Control ⚙️.

Step 1: Connect Signal Source

Connect your Signal Source to the DTV/TV connection, then proceed to Step 2.

Please Note: ? Be sure the batteries in your remote are inserted correctly.

Step 2: On-Screen Setup

1. Turn on the TV ?. The Initial Setup screen should appear. If this screen does not appear, see User Manual Chapter 3 for TV Tuner Setup.
2. Select Language: English, Français, Español.
3. Press the [Arrow Keys] or [OK Button] to select Cable or Antenna. Select 'Cable' if you are using cable from the wall, or 'Air' if you are using an antenna.
4. Press the [Arrow Keys] to continue to the next screen.
5. Press the [OK Button] on the remote to start Channel Scanning. Scanning for available channels could take several minutes.
6. Once scanning is finished, programming is complete.

For more detailed information, see Chapter 3 of your User Manual.

Programming Your Cable or Satellite Box Remote

Consult your Cable or Satellite Owner's Manual to determine if you need a 3, 4, or 5-digit code. If your Cable or Satellite Box requires:

• 3-digits: Please use "627" (This code usually works with DISHNetwork.)
• 4-digits: Please use "1758", "0178", or "0128".
• 5-digits: Please use "11758", "10178", or "10128" (These codes usually work for DIRECTV.)

Pairing Your TV and Wireless Speakers

Before trying to make any connection, please familiarize yourself with your new wireless speaker's set supplied with your new VIZIO JV50P HDTV. The set consists of two satellite speakers (labeled left with a white connector and right with a red connector) and a subwoofer. The subwoofer acts as the brain of the set. Please take a look at the back side of the subwoofer and notice the following: a three-prong power connector (labeled AC IN ?), two plug-in sockets (labeled SPEAKER), and a small button or switch (labeled CH-SEARCH**, PAIRING).

The AC IN is where power is supplied to the set. The two SPEAKER connectors (towards the bottom right-hand side, labeled LS for left speaker and RS for right speaker) are where the satellite speakers connect by matching the colors. The small button will be the one to keep attention to; it is used (press) when following instructions (Steps) to pairing the TV and Wireless speaker setup.

Pairing Procedure

1. Using the Remote Control ⚙️, turn the TV set ON ?.
2. Press the [MENU Key] on the Remote Control. The screen should display a menu window with five icons across the top.
3. Using the [Right Arrow Key], navigate to the [Audio Icon] (looks like a microphone on a stand). Select it with the [OK Button].
4. On this menu, check that the Speakers and Wireless Speakers option are selected to be ON. If not, switch them ON by using the [Right Arrow Key] after selecting them individually.
5. Place the subwoofer 10 to 12 feet away from the TV set, with the subwoofer facing the TV screen.
6. Turn OFF the TV set ?.
7. Plug the wireless speaker system power cord into an electrical outlet to power it up.
8. While pressing and holding down the PAIRING (LINKING) switch [CH-SEARCH/PAIRING Button] at the back of the woofer, turn the TV set ON using the Remote Control ⚙️.
9. The light indicator ? [*] on the front of the subwoofer will stop flashing and stay ON, indicating that the pairing has been accomplished.
10. Release the PAIRING (LINKING) switch [CH- নিরাপদ/PAIRING Button] and enjoy the sound.
11. If pairing (linking) is not successful, please repeat steps 6 through 10.

Note: Please notice that the light indicator ? remains flashing at a slow rate when no signal is being fed to the wireless speaker system.

Note: If wireless transmission interference occurs, simply turn off and then turn on the TV for automatic channel scanning of the next available transmission channel.

Optional Components

Enhance Your VIZIO Experience

When it comes to components and accessories, don't settle for less than VIZIO. VIZIO offers a full line of products specifically designed to accentuate your JV50P. To learn more about how you can enhance your VIZIO experience, call 888-849-4623 or visit www.VIZIO.com.

VIZIO High-Definition Certified Cables

Our VIZIO Certified HD cables carry the same standards of excellence as all VIZIO products. Available in: DVI, HDMI, and Component in lengths of 2, 5, and 10 meters.

VIZIO Certified Mounts

• Flush Mount: Turns your HDTV into a work of art.
• Tilt Mount: Adjusts your HDTV for the most comfortable viewing position.
• Articulating Arm: Positions your HDTV exactly where you want it.

Extended Service Plans

For more information or to sign up for any VIZIO extended service plans, call (800) 988-4196 or visit us online at: www.VIZIO.com.