ETA Naos 2607 Stand Fan

Safety Warnings ⚠️

• Check that the data on the type label corresponds with the voltage in your socket. The power cord plug must be connected to a properly connected and grounded socket according to national standards.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, if they are supervised or instructed on safe use and understand the hazards. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision. Children younger than 8 years must be kept out of reach of the appliance and its power cord.
• Before replacing accessories or accessible parts, before assembly/disassembly, cleaning, or maintenance, turn off the appliance and disconnect it from the mains by pulling the power cord from the socket.
• Always unplug the appliance from power supply if left unattended and before assembly, disassembly, or cleaning.
• Never use the appliance if the power cord or plug is damaged, if it is not functioning correctly, or if it has fallen and been damaged or fallen into water. In such cases, take it to a professional service centre.
• If the power cord is corrupted, it must be replaced by the manufacturer, its service technician, or a similarly qualified person to prevent dangerous situations.
• The appliance is intended for home use and similar environments (shops, offices, hotels, etc.), not for commercial use.
• The fan must not be immersed in water or other liquids (even partially) and must not be used near bathtubs, showers, wash basins, or other water containers, including swimming pools. If it falls into water, do not take it out; unplug first, then remove. Take to a service centre for checks.
• This appliance is not intended for outdoor use.
• Do not plug or unplug the cord with wet hands or by pulling the cord.
• The appliance cannot be used in bathrooms in zones 0, 1, and 2.
• Do not use in damp or wet environments or in areas with fire or explosion risk (e.g., where chemicals, fuels, oils, gases, paints, or other flammable/volatile materials are stored).
• Use the appliance in a working position only, on stable surfaces, away from objects (curtains, drapes), heat sources (fireplace, stove, radiators), and wet surfaces (sinks, wash basins).
• Prevent impurities (dust, hair, etc.) from entering the appliance.
• Do not place the switched-on fan on soft surfaces (bed, towels, carpets).
• Do not alter the appliance's surface (e.g., with stickers or foil).
• Handle the appliance carefully to avoid injury.
• Do not place devices with open flames in the airflow; this could interrupt the burning process.
• Never direct the airflow at yourself or pets for extended periods, as it may cause health problems.
• Use only original parts intended for this type.
• Do not cover air vents.
• Never insert fingers or other objects into the air inlets or outlets.
• Regularly check the power cord's condition.
• Do not place the power cord on hot surfaces or let it hang over edges. Pulling the cord (e.g., by children) can cause the appliance to tilt or fall, leading to serious injury.
• The power cord must not be damaged by sharp or hot objects, open fire, or be bent over sharp edges. Do not immerse in water.
• Do not wind the power cord around the appliance; this shortens its lifespan.
• If using an extension cord, ensure it is undamaged and meets regulations.
• If a battery leaks, replace it immediately to avoid damaging the remote control.
• Dispose of used batteries properly (see Environmental Protection section).
• Keep batteries and remote control out of reach of children and incapacitated persons. Seek immediate medical help if a battery is swallowed.
• WARNING: Improper use according to the manual may cause injury.

Description of the Appliance

A – Drive Unit

• A1 - Shaft
• A2 - Adjustable joint angle
• A3 - Power cord
• A4 - Screw
• A5 - Height adjustment nut
• A6 - Extension pole (2x)
• A7 - Base
• A8 - Screw + Gasket
• A9 - Rear grill
• A10 - Grill nut
• A11 - Blade
• A12 - Blade nut
• A13 - Plastic connecting collar
• A14 - Clip
• A15 - Front grill
• A16 - Screw

B – Control Panel

• B1 - Oscillation adjustment button
• B2 - Timer setting button
• B3 - Mode button (NORMAL / NATURAL / SLEEP)
• B4 - Speed setting button (F1 / F2 / F3 / F4)
• B5 - ON / OFF button ⏻
• B6 – Display

C – Remote Control

• C1 - Oscillation adjustment button
• C2 - Timer setting button
• C3 - Mode button (NORMAL / NATURAL / SLEEP)
• C4 - Speed setting button (F1 / F2 / F3 / F4)
• C5 - ON / OFF button ⏻

Instructions for Use

Assembly

Follow Fig. 1 for assembly. To mount the plastic connecting collar A13, loosen clip A14 and screw A16 to easily fit the collar onto the rear and front protective covers (A9/A15). Then, gently tighten clip A14 and screw A16. Adjust the required height and secure by tightening nut A5. Disassembly is the reverse process.

Note: For safety, shaft A1 and blade nut A12 have an anti-clockwise thread.

Operation

The fan can be operated via control panel B or remote control C. For the remote control, insert one CR 2025 3V battery, observing correct polarity. Information is shown on the display and control panel (Fig. 1).

Turning the fan on/off

Press the B5/C5 button to turn the fan on. Press B5/C5 again to turn it off. Display B6 shows 0F (stand-by mode).

Adjusting the air blow rate

Press the B4/C4 button to set the air speed in 4 levels. The set level is indicated by a corresponding light and numbers (F1, F2, F3, F4) on the display.

Oscillation Settings

Press the B1/C1 button to turn oscillation on. Press B1/C1 again to turn it off. During oscillation, the fan rotates approximately 45° back and forth. Oscillation activation is indicated by a light.

Setting the Mode

Press the B3/C3 button to switch between modes:

Timer Function ⏱️

After turning the fan on and setting the mode, use the B2/C2 button to set the desired operating time. Press and hold for 3 seconds to confirm. The timer can be set from 1-15 hours. The set time is indicated by a light. The fan will automatically turn off after the set time has elapsed.

Notes: The timer function can be set and combined with NORMAL / NATURAL / SLEEP modes.

Maintenance

The appliance requires only surface maintenance. Clean the surface of the appliance and the power cord with a damp cloth.

Environmental Protection ♻️

If dimensions allow, materials used for packaging, components, and accessories are marked for recycling. Symbols on the product or documentation indicate that electrical/electronic products must not be disposed of with municipal waste. Take them to designated collection points for free disposal. Proper disposal helps conserve natural resources and prevent negative impacts on the environment and human health. Contact local authorities or collection sites for details. Improper disposal may incur fines according to national regulations. To permanently disable the appliance, disconnect the power cord from the mains and cut it off.

Technical Data

The manufacturer reserves the right to change technical specifications and accessories. Replacement of parts requiring intervention in the electric part of the appliance must be carried out by a specialized service. Failure to comply with manufacturer's instructions voids the warranty.

Warranty Information

The product is covered by a 24-month warranty from the date of sale. The warranty covers defects caused by manufacturing errors or faulty materials. Claims must be made at the point of sale or an authorized service centre, presenting the product, proof of purchase (with product type and date), and the completed warranty card. Warranty is void if: the appliance is tampered with by unauthorized persons, improperly installed or used, damaged by natural disasters, used for commercial purposes, used with non-recommended accessories, improperly maintained, damaged by foreign objects/liquids, or mechanically damaged due to improper use or dropping. If sending for repair, package securely. For service centre locations, visit www.eta.cz.