xTool D1 Pro Quick Start Guide

Thank You!

Dear xTooler,

Thank you for purchasing the xTool D1 Pro. We are grateful for your recognition and hope you enjoy this product. The xTool D1 Pro is a high-accuracy and high-power laser engraver and laser cutter, suitable for users from novice to expert, and for home use to business. Our mission is to make it easier for everyone to create with our machine. We value your experience and suggestions. Please let us know if you have any questions. You can join our Facebook group with over 25,000 innovators to share creative ideas and get inspired. Visit our online store for the latest accessories and materials to maximize your xTool D1 Pro experience.

Thanks again for your support. We will consistently provide quality products and services.

Sincerely,
Jason Weiy
CEO

Official Website: www.xtool.com

Facebook Group: xTool D1 Official Group / Makeblock xTool Official Group

Support Center: support.xtool.com

Technical Support: support@xtool.com

Contents

• Unbox and check
• Assemble xTool D1 Pro
• Meet your xTool D1 Pro
• Set up xTool D1 Pro
• Download and install software
• Create with example projects
• Use Rotary Attachment 2
• Clean the laser module

Note: This user manual uses the golden red version to describe assembly and setup. xTool D1 Pro is available in two color options.

Unbox and Check

Ensure all components are present:

• Plate components (A, B, C, D, E)
• Power adapter & cable
• USB cable
• Motor cable
• Cable tie pack
• Limit switch connection cable
• Shaft
• Parts storage box
• TF card
• Coupling
• Screwdriver
• Hex key
• Screws (M4*8, M4*16, M4*25)
• Nozzle connector components
• Laser module
• Safety goggles
• Material pack
• Quick Start Guide/Instructions/Brochure
• Aluminum sheet A4
• Riser (included in some packs)
• Rotary Attachment 2 components (included in some packs)

Assemble xTool D1 Pro

Follow these steps to assemble your xTool D1 Pro:

1. Connect the frame components (A, B, C, D) as shown in the diagrams. Ensure proper alignment.
2. Attach the shafts to the frame.
3. Use screws to set the tension of the timing belts. Do not fully tighten them to avoid damaging the belts. If the shaft is difficult to insert, the belt may be too tight; adjust the screw.
4. Keep a small distance between the coupling and the motor for proper rotation and to prevent noise.
5. Slide the two sliders down against the front plate.
6. Fully tighten the two screws. Pay attention to the front and back sides of the connector for proper insertion.
7. Cut off the white cable ties and keep the black ones.
8. Attach the laser module to the frame using the thumb screw. Turn the handle clockwise to tighten, hold to draw away from the thread, rotate to stop blockage, release, and repeat if necessary.
9. If the handle is blocked, tighten or loosen the screw by rotating the handle.
10. Insert the TF card before use. Functions like Wi-Fi processing, offline processing, and framing may fail without it.

Tip: The secret to getting ahead is getting started. Let's go!

Tip: You can visit support.xtool.com or scan the QR code for a tutorial video.

Meet Your xTool D1 Pro

Familiarize yourself with the components of your xTool D1 Pro:

• Hole for fitting an exhaust pipe
• Focal length setting bar
• Nozzle connector
• Indicator
• Button
• Laser module
• USB port
• Wi-Fi antenna
• Power port
• Power switch

Congratulations! You have completed the installation. Download the software and get the novice task for a creative and memorable first project.

Set Up xTool D1 Pro

Adjust the tension of the timing belts

Try to set the timing belts on the right and left plates to the same tension for proper cutting and engraving performance.

Set the position of the laser module

To cut thicker materials, adjust the position of the rear plate on the laser module based on the scale aligned with the focal length setting bar.

• For the 20 W laser module:
• For the 40 W laser module:

Tip: Settings are tested in a laboratory environment and are for reference only. Settings may vary by material; test materials before processing.

Download and Install Software

Download xTool Creative Space (XCS) from xtool.com/software or use the third-party software LightBurn (purchase required).

Create with Example Projects

xTool D1 Pro comes with a material pack to get you started. Scan the QR code or navigate to Support > xTool D1 Pro > xTool D1 Pro Example Project Files & Tutorials within XCS to find example projects and tutorials.

Tip: Before creating, test parameter settings and engraving performance to prevent material waste. For valuable items, test on a substitute material.

Use Rotary Attachment 2

Connect xTool D1 Pro to Rotary Attachment 2 to engrave cylindrical or irregular materials. It requires specific device and software. For usage details, visit support.xtool.com.

Level Reference:

• Level A: 3 mm ≤ diameter ≤ 50 mm
• Level B: 45 mm ≤ diameter ≤ 60 mm
• Level C: diameter > 60 mm

Set the level: Adjust the level of the Rotary Attachment 2 based on the material's diameter. Use the changing of the level from C to B as an example.

Tip: Place Rotary Attachment 2 parallel to the working area. Set its level based on the material's diameter before connecting it to xTool D1 Pro.

Use the Support Module

The support module is for processing irregular objects or objects too long for Rotary Attachment 2. Place the support module as required.

Set the support module: Turn the knob clockwise to move support wheels upward, or counterclockwise to move them downward.

Clean the Laser Module

For the 20W laser module: Clean the inner and outer frames of the light shield, lens, and red light outlet every hour of use.

Clean the laser module when the light shield is dirty or laser beams cannot cut material.

1. Turn off the device and remove the laser module.
2. Remove the nozzle and its connector from the laser module.
3. Clean the inner and outer frames of the light shield with tissues or dust-free cloth moistened with alcohol. Clean the lens and red light outlet with a cotton swab moistened with alcohol.