MCombo High Leg Power Recliner Chair

Hello, Thank you for choosing MCombo® Let's get started

Purchaser's Agreement: By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or render inoperable or unsafe any guards, shields or other safety features of this product. You will not refuse or neglect any retrofit kits that MCombo may provide to enhance and preserve the safe use of this product.

Safety Guidelines

1. Mandatory

Read the safety and other instructions thoroughly before using your MCombo® product. Failure to follow the guidelines, warnings in this manual and those located on your product can result in personal injury or product damage and will void the product warranty. Keep this manual for future reference.

2. Danger ☠️

• To prevent suffocation, keep plastic bags away from children.
• Do not allow children play on or near the chair when in use. Serious injury or death could occur if a child is under the chair when the chair is in motion.
• Keep cord out of reach of small children, and do not use where it may be a trip hazard.
• Plug directly into a wall outlet. Do not use an extension cord or adapter.
• Do not use this product if it is wet, in water, around water or any liquid.
• Always leave in an upright and closed position. Keep hands and feet clear of mechanism and all moving parts. Footrest must be completely closed before getting in or out of the chair. Only the occupant should operate the chair.
• Before moving or troubleshooting, unplug power cords from outlet and secure the mechanism to prevent unexpected movement of the chair.

3. Warning ⚠️

• Weight Capacity: 350 lbs.
• Do not use outdoors. INDOOR USE ONLY.
• To avoid tip over, do not put your weight against the back of the chair.
• Do not stand, sit, or place extra weight on the arms, back or open footrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• Avoid exposing upholstered chair to burning cigarettes or cigars, open flames, and high temperatures.
• Do not operate the unit until the back is installed and locked.
• Do not attempt to disassemble or repair the actuator or pump; no serviceable parts are inside.
• Do not allow electrical cord to be pinched between moving parts or between the frame and the floor. Do not place cord under carpet or in a location where it could become worn.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power plug and pull it out.
• Closely supervise children and disabled persons using this product.
• To reduce the risk of head entrapment and other injuries, keep children and pets away from openings and moving parts in and around furniture.
• This product has many moving parts, serious injury can occur if not used properly. Keep hands, fingers, and body parts away from the mechanism.
• To exit the unit safely and prevent a tripping hazard, bring the back upright and close the footrest.
• Place tables and area rugs at a distance to allow the footrest to fully extend without rubbing or interference.
• Check the condition of the power supplies, electrical cords, plugs, and connectors often. Keep the power supplies and electrical cords away from heat sources. Never operate the unit with a damaged power supply, electrical cord, plug or connector.
• Do not charge your device into the USB charge ports over 24 hours.
• Do not charge any devices over 5V/2A with the USB charge ports.
• Do not overlay the USB charge ports with other heat-dissipating electronic products. This may prevent heat dissipation and cause overheating or melting.
• Unplug the power cord immediately if you detect strange odors or fumes coming from the chair. Contact your MCombo Customer Support.
• The chair is intended for a single occupant, not exceeding 350 pounds. Do not operate the chair with more than one occupant in or on any part of the chair.
• If you give this product to someone else, must include this owner's manual.

4. Symbols Information ℹ️

The symbols below represent labels used on the product to identify warnings, mandatory actions, and prohibited actions. It is especially important for you to read and understand these symbols completely. Do not remove these labels from your product. Please note that not all the symbols may be used on your chair.

• Read and follow the information in the owner's manual.
• Weight Capacity: 350 lbs.
• Do not place objects under the footrest when it is in fully reclined position.
• Do not place objects under the headrest when the headrest of the recliner sofa is in the fully raised position.
• Do not connect an extension cord to the AC/DC converter.
• Pinch/Crush Points Hazard.
• Electrical Hazard.
• Class II Equipment.
• Indoor Use Only.

5. Disclaimer

Make sure you read and understand this manual completely before using your MCombo Product. We are not and cannot be held responsible for any damage or injury incurred due to improper or unsafe use of the MCombo Product. We specifically disclaim responsibility for any bodily injury or property damage that may occur during any use that does not comply with applicable federal, state, or local laws or ordinances.

Assembly Instructions

Notice

• Please read these instructions thoroughly before using.
• Do not plug the power supply in until assembly is complete.
• Please contact us (See "Mcombo Customer Support" on Page) immediately if anything is missing or damaged.

1. Product Parameters

2. Part List

Notice: Use Mcombo parts only for all replacements.

Box 1 of 3:

• A Base x 1
• H Hexagonal Screw x 4 (spare x 2)
• J Power Adapter x 1
• K Wooden High Leg x4
• X Hex Key x 1
• Y Support Leg x 4
• Z Anti-tipping Forward x 2

Box 2 of 3:

• E Backrest x 1

Box 3 of 3:

• C Left Armrest x 1
• D Right Armrest with USB x1

3. Assembly Steps

Notice: Use Mcombo parts only for all replacements.

Step 1 - Remove Protective Round Bar

Use the hex key to unscrew both ends of the iron bar and remove the iron bar.

Before assembly, please remove the protective round iron bar from the base brackets.

[Diagram: Shows a recliner base with a round bar attached by screws, an arrow indicates unscrewing.]

[Diagram: Close-up of hex key turning a screw on the round bar.]

Step 2 - Anti-forward-tipping Parts Assembly

1. Turn the two bases on the right side until Step 3.
2. Screw one Anti-forward-tipping part into the two preset holes in the bottom inboard of the base. (Figure)

[Diagram: Shows attaching anti-tip brackets to the base.]

Step 3 - Support Legs Assembly

1. Turn the base on its right side until Step 3.
2. Screw the support legs into the preset holes in the bottom of the base.
3. Make sure four support legs are properly screwed in tightly and ensure all legs do not move.

[Diagram: Shows screwing support legs into the base, with a close-up of the screw and leg.]

Step 4 - Backrest Assembly

1. Connect the headrest wire with the corresponding base wire.
2. Align the brackets of the backrest at the clips of the seat-back.
3. Push firmly the brackets into the seat-back. Listen for a "click" on each side to ensure the backrest is locked in properly.

NOTE: Pull up the backrest to check if it is locked in place.

[Diagram: Shows connecting wires and aligning backrest brackets with the seat base.]

[Diagram: Close-up of backrest bracket clicking into place.]

Before assembling the backrest, please connect the headrest wire with the corresponding base wire.

Step 5 - Adjustable Support Legs Assembly

1. Turn the armrest upside down until the end of Step 5.
2. Screw the screw and gasket into the preset holes at the bottom of the armrest.
3. Make sure the screw is properly screwed in then tighten them.
4. Ensure the legs do not move.
5. Repeat above 4 steps for the other armrest.

[Diagram: Shows attaching screws and gaskets to the bottom of an armrest.]

Step 6 - Armrests Assembly

1. Ensure the armrest which has the USB charge port is located on the right of the seat.
2. Slide the left and right armrests into the brackets of the seat.
3. Press each armrest down as far as it will go.

NOTE: Ensure the two connections on each armrest are both inserted onto the seat tightly.

ATTENTION

Ensure the two connections on each armrest are all inserted onto the seat tightly.

[Diagram: Shows sliding armrests onto the seat base, with a close-up of the connection points.]

Step 7 - Connections

Connect the recliner sofa according to the following wiring diagram.

NOTE: The armrest wire needs to be wound under the base to avoid the wire is crushed by the rack frame.

[Diagram: Shows the wiring connections between the base, backrest, and armrests, including power adapter.]

Step 8 - Paste Velcro

1. Place the chair in the reclined position.
2. Pull out the Velcro in the gap between the base and the backrest and paste it well.

[Diagram: Shows pulling Velcro strips to secure the backrest to the base.]

Step 8 - Final Check

1. Make sure both metal brackets on each armrest are mounted on the base. (There are two metal brackets on each side of the base; it looks like assembly is finished when you insert the armrest into only one bracket instead of two, however, all pressure will apply to one bracket, that is one likely reason that the armrest falls apart from the base.)
2. Make sure the backrest inserts are locked to the base.
3. Make sure all wires are connected tightly.
4. Make sure all wires did not place the bottom of the rack and will not be pressed by frame. (If the wire is pressed by the frame, the wire will be broken by the frame and the chair will stop working.)
5. Make sure all screws on four wooden high legs and four support legs are tightened.

Operating Instructions

1. Operation Precautions

• Do not use an extension cord.
• Do not exceed recommended weight limit.
• Do not use outdoors. INDOOR USE ONLY.
• Keep dry. Do not operate in a wet or moist environment.
• Keep all cords away from heated surfaces and pinch points.
• Do not use attachments not recommended by the manufacturer.
• Periodically check the control and all power cords for visible damage.
• Always leave the lift chair in an upright and closed position when not in use.
• Do not use the footrest as a seat, or for purposes outside its intended use.
• Do not lean or apply downward force to the chair-back while in recline position.

NOTE: If you discover a problem at any point during the setup and positioning of your power recliner sofa, stop and contact the Mcombo Customer Support immediately. To avoid personal injury or product damage, do not plug the unit into the electrical outlet until the problem is corrected and do not attempt to fix electrical problems by yourself.

2. Operation Instruction

Control Buttons:

The control panel typically includes:

• USB Charge Port: For charging devices.
• Footrest Buttons: < (Down) / > (Up)
• Headrest Buttons: < (Down) / > (Up)
• Home Button: Press to return the headrest and footrest to their original positions.

[Diagram: Shows a control panel with labels for USB port, footrest buttons, headrest buttons, and home button.]

Chair Positions:

• Seated: For a short break, offering a comfortable experience.
• Relaxing: Adjust the footrest and headrest positions for relaxation.
• Napping: Adjust the headrest and raise the footrest for a comfortable nap.

[Diagram: Illustrates the Seated, Relaxing, and Napping positions of the recliner.]

Care and Maintenance

1. Fabric Care

• Inspect the fabric on a regular basis for any pulls, tears, or gaps.
• Frequent vacuuming or light brushing with a nonmetallic, stiff bristle brush to remove dust and grime is recommended.
• When liquid spills onto the fabric, please immediately wipe off liquid spills with a dry or lightly dampened clean white cloth, sponge, or paper towel.

2. Faux Leather Care

• Wipe leather down regularly with a clean, dry microfiber cloth.
• For more stubborn dust, dampen the cloth with distilled water. Make sure that the cloth is not soaking wet. Never let water soak into leather.
• Always be sure to use a soft cloth and never use an abrasive brush or scrubber as this can scratch and damage the leather.

3. Electronics Care

• Inspect all wiring harnesses to make sure they are not damaged or stuck under the chair.
• Keep all the electronics free from moisture and temperature extremes.
• Check electrical components frequently for signs of corrosion and replace as necessary.
• Contact Mcombo Customer Support if damage is present; do not fix it by yourself.

4. Disposal & Recycling

Your power recliner sofa must be disposed of according to applicable local and national statutory disposal regulations. Contact your local waste disposal agency for information on proper disposal of recliner sofa packaging, metal/wood frame components, fabric, and electronic components.

Troubleshooting

The following troubleshooting FAQs should summarize what you need to know about your power recliner sofa. If at any time you do not feel comfortable performing the troubleshooting steps listed in this manual, please contact Mcombo Customer Support for service.

NOTE: If the recliner sofa does not operate properly, please contact the Mcombo Customer Support for help and never attempt to make any repairs or adjustments yourself.

Disassembly Instruction

Notice:

• Ensure the chair is in upright position and its footrest and headrest return to original position.
• Please unplug the power adapter before disassembling.
• Please dismantle the power recliner sofa in strict accordance with the order in which they were dismantled.

Step 1 - Disconnect all Connections

Please disconnect all connections on the chair base and backrest before disassembling.

Step 2 - Disassemble Armrests

1. Use your knees to find a support point on the seat and press on the base with your own strength.
2. Hold the two marked positions at the bottom of the armrest and lift the armrest vertically upward.

ATTENTION

Shake the armrest slightly to loosen the brackets, make it easier to detach from the base.

[Diagram: Shows how to detach armrests.]

Step 3 - Disassemble Backrest and Anti-forward-tipping

1. Pushing the metal ears of the bracket inserts outward.
2. After unlocking the metal lugs on both sides of the backrest, hold the bottom part of the backrest marked in the picture below and pull it vertically upward.
3. Unscrew the anti-forward-tipping part out of the preset holes at the bottom of the inside of the base.

[Diagram: Shows how to release backrest and remove anti-tip parts.]

Step 4 - Disassemble Legs

Please use Hex key to remove four wooden high legs and four support legs.

[Diagram: Shows using a hex key to remove legs.]

NOTE:

• If the chair needs to be returned, please pack all screws, feet, power supply and other accessories into the box.
• Please refer to the 5-page part list and 22-page return for other packing methods.

Warranty

Notice:

• For products beyond the limited manufacturer warranty period and scope, Mcombo® can also provide replacement service, but a basic charge will be charged according to the circumstances.
• The warranty only applies to Mcombo® products and does not include any accessories or enhancements.
• Warranties are only valid in the 48 contiguous United States and are contingent upon the consumer operating the product according to the corresponding instruction manual.

CONSUMER WARRANTY LIMITATIONS AND EXCLUSIONS

All warranties begin on the date of delivery. All warranties are to the original purchaser from MCOMBO® ONLY.

• MCOMBO® will replace the defective parts or send replacement product provided that the warranty parts have not been subjected to misuse, abuse or improper service by the consumer, for example, damaged wire arising in consequence of negligence or improper operation.
• Exclusions also include components with damage caused by:
  • Contamination
  • Abuse, misuse, accident, or negligence
  • Commercial use, or use other than normal
  • Improper operation, maintenance, or storage

NOTE: MCOMBO® will pay standard shipping rates on all warranted parts for the first year. We can also sell you replacement parts for a discount price when your product is out of warranty policy.

Return/Replacement Policy

Notice: Why don't we recommend returning the item by yourself?

• Huge cost - UPS/FedEx oversize fee.
• Need you to take the box to UPS/FedEx facility.

Return/Replacement Policy

All products come with a 30-day return/replace policy. During this time, Mcombo will cover the shipping cost of return and replacement for defective and damaged products, through providing pre-paid return label or pick-up service for customer convenience.

NOTE:

• Please keep the original packaging in case the product needs to be returned. If the original packaging is not available, the newly found packaging needs to meet the following size standard: UPS/FedEx packaging size standard: (width+ height) * 2+ length < 128 inch.
• Please disassemble the product before you return it, otherwise there will be a huge cost as oversized and it could even exceed your order amount.
• Please do not purchase return label for a damaged/defective product by yourself.
• If you have any problem to return the product, please contact us immediately, we will do our best to help you with a reasonable solution.
• The customer is responsible for freight costs unless the chair is defective. Chairs returned due to being refused delivery by the customer or deemed undeliverable by freight carrier are subject to fees for a 20% restocking fee.

Mcombo Customer Support

If for any reason, we have fallen short of your expectations, or if you have any questions and suggestions, please refer to the following contact information. We will do our best to work with you to make sure you are entirely satisfied.

• Email: sales@mcombo.com (Respond within 24 hours)
• Phone: 1-323-597-1109 (8:00 a.m.--4:00 p.m. Monday--Friday) TIME ZONE: PST

Locations:

• DE: 2411 Bear Corbitt Rd STE 1, New Castle, DE, 19720
• TN: 3980 PREMIER AVE, MEMPHIS, TN, 38118
• CA: 2808 Vail Ave, Commerce, CA, 90040; 3400 Yosemite Ave, Lathrop, CA, 95330