Installation Instructions – Smart Pixel LineLED Decoder
Models SR-DMX-SPI
SR-DMX-SPI Smart Pixel LineLED Decoder
Please read all instructions prior to installation and keep for future reference!
- ENSURE POWER TO POWER SUPPLY IS OFF BEFORE INSTALLING
- PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
- USE ONLY WITH CLASS 2 POWER UNIT
Prior to installing determine the location, which requires a minimum of 2” clearance around the decoder to provide proper air circulation.
Remove covers on both sides of Smart Pixel LineLED decoder by using a small screwdriver. Store covers and their fasteners until decoder setup is complete and functioning properly and then re-install them.
Please read all instructions prior to installation and keep for future reference!
- ENSURE POWER TO POWER SUPPLY IS OFF BEFORE INSTALLING
- PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
- USE ONLY WITH CLASS 2 POWER UNIT
OPERATING GUIDE
SR-DMX-SPI
DMX512 Pixel Signal Decoder
There are three buttons on the decoder.
 |
Parameter Setting |  |
Increase Value |  |
Decrease Value |
After operation, if no action was taken within 30s, the button lock, and backlight of the screen will turn off.
- Long press M button for 5s to unlock the buttons, and the backlight will turn on.
- Long press M button for 5s to switch between test mode and decode mode after unlocked.
During test mode, the first line of LCD will show: TEST MODE. Use test mode to verify RGBW Pixel functionality.
Duirng decoder mode, the first line of LCD shows: DECODER MODE. Use decoder mode when connecting to a Controller and for final installation and customization.
NOTE: When connected to a controller, DMX512 Signal Decoder will stay in “Decoder Mode”.
The second line of the LCD Display shows the current setting and value. Note: 1 Pixel = 1 Cut Increment
MODE TABLE
| SETTING | LCD DISPLAY | VALUE RANGE |
DESCRIPTION |
| Built-in Programs | TEST MODE MODE NO.: | 1-26 | See Program Table below |
| Program Speed | TEST MODE RUN SPEED: |
0-7 | 0: fast, 7: slow |
| DMX Address | DECODER MODE DMX ADDRESS: |
1-512 | Address of the starting point/Pixel of a program |
| DMX Signal RGB | DEE)C01:ARBAOSE MX | RGB, BGR, etc. | N/A |
| Pixel Quantity | DECODER MODE PIXEL QTY: |
1-170(RGB), 1-128(RGBW) | Number of Pixels to follow a program |
| IC TYPE | DECODER MODE IC TYPE: |
2903, 8903, 2904, 8904 |
2903: N/A, 2904: for RGBW, 8903: N/A, 8904: N/A |
| Color | DECODER MODE COLOR: |
MONO, DUAL, RGB, RGBW |
MONO: N/A, DUAL: N/A, RGB: N/A, RGBW: for RGBW |
| Pixel Merging / Pixel Size |
DECODER MODE PIXEL MERGE: |
1-100 | Number of Pixels to merge together |
| RGB Sequence | DECODER MODE LED RGB SEQ: |
RGBW, BGRW etc. |
Sequence of RUM, 24 possible combinations |
| Integral Control | DECODER MODE ALL CONTROL: |
YES, NO | Yes: Merge all Pixels No: Maintain individual Pixels or Merged Pixels |
| Reverse Control | DECODER MODE REV-CONTROL: |
YES, NO | Reverse program order |
| Overall Brightness | DECODER MODE BRIGHTNESS: |
1-100 | 1: dimmest setting 100: brightest setting |
NOTE:
The actual maximum control pixels of the controller are 1360 (2903) ,1024 (2904). Please set the pixel and pixel combination value according to the actual situation, and DO NOT exceed the maximum.
NOTE: For Program Table Change: no fading/dimming between color changes Fade: fade/dim between color changes Chase: change pixel by pixel Chase with Trail: change pixel by pixel with fading between
PROGRAM TABLE
| PROGRAM NO. | PROGRAM DESCRIPTION | PROGRAM NO. | PROGRAM DESCRIPTION | PROGRAM NO. | PROGRAM DESCRIPTION |
| 1 | Solid color: Red | 10 | RGB fading | 19 | Red chasing green, chasing blue |
| 2 | Solid color: Green | 11 | Full color fading | 20 | Orange chasing purple, chasing cyan |
| 3 | Solid color: Blue | 12 | Red chase with trail | ||
| 4 | Solid color: Yellow | 13 | Green chase with trail | 21 | Rainbow chase (7 colors) |
| 5 | Solid color: Purple | 14 | Blue chase with trail | 22 | Random twinkle: white over red |
| 6 | Solid color: Cyan | 15 | White chase with trail | 23 | Random twinkle: white over green |
| 7 | Solid color: White | 16 | RGB chase with trail | 24 | Random twinkle: white over blue |
| 8 | RGB change | 17 | Rainbow chase with trail | 25 | White fading |
| 9 | Full color change | 18 | RGB chasing and fading | 26 | Off |
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
info@luminii.com
www.luminii.com
Documents / Resources
 |
luminii SR-DMX-SPI Smart Pixel LineLED Decoder [pdf] Instruction Manual SR-DMX-SPI Smart Pixel LineLED Decoder, SR-DMX-SPI, Smart Pixel LineLED Decoder, Pixel LineLED Decoder, LineLED Decoder, Decoder |
