Instruction Manual for luminii models including: SR-DMX-SPI Smart Pixel LineLED Decoder, SR-DMX-SPI, Smart Pixel LineLED Decoder, Pixel LineLED Decoder, LineLED Decoder, Decoder
SR-DMX-SPI - Luminii
File Info : application/pdf, 2 Pages, 305.87KB
DocumentDocumentInstallation Instructions - Smart Pixel LineLED Decoder Models SR-DMX-SPI Please read all instructions prior to installation and keep for future reference! 1. ENSURE POWER TO POWER SUPPLY IS OFF BEFORE INSTALLING 2. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN. 3. USE ONLY WITH CLASS 2 POWER UNIT REV0.1 08012022 1 / 2 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com cover cover In Out Display Screen Prior to installing determine the location, which requires a minimum of 2" clearance around the decoder to provide proper air circulation. Remove covers on both sides of Smart Pixel LineLED decoder by using a small screwdriver. Store covers and their fasteners until decoder setup is complete and functioning properly and then re-install them. WIRING DIAGRAM SR-DMX-SPI Smart Pixel LineLED Decoder NOTE: Please make sure that power is turned off before wiring. Also, ensure that the correct power supply (voltage and wattage) is used to power the LED strips connected to the decoder. Follow illustrated wiring diagram. Use screwdriver to open and close connection slots. NOTE: When connecting two or moreBLEeDfostrreip lwighirtsinorgli,ghetnfixstuurrees, palowwaysemr aikseosufrfettohepsiognwaledrirection arrows are pointing to same direction supply The signal direction arrow should appeAalrsoon, eeancshusreecttihonat(ctuhteinccroemrreenct)t opfoLEwDesrtrispupply (voltage and wattage) is used to power the LED strips Signal direction arrow connected to the decoder. Follow illustrated wiring diagram. Use screwdriver toSigonpael dniraecntdioncalorrsoew 24V+ connection slots. 24V+ 24V- 24V- NOTE: Must power from the opposite direction of the signal direction arrow CONTROLLER WIRES 1000 ft max, decoder to Controller In Out 32 ft max, decoder to strip 24V+ 24V- PIXEL LED (-) POWER SUPPLY (L) output (+) 24VDC AC input (N) *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE Installation Instructions - Smart Pixel LineLED Decoder Models SR-DMX-SPI Please read all instructions prior to installation and keep for future reference! 1. ENSURE POWER TO POWER SUPPLY IS OFF BEFORE INSTALLING 2. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN. 3. USE ONLY WITH CLASS 2 POWER UNIT OPERATING GUIDE SR-DMX-SPI DMX512 Pixel Signal Decoder There are three buttons on the decoder. Parameter Setting Increase Value After operation, if no action was taken within 30s, the button lock, and backlight of the screen will turn off. 1. Long press M button for 5s to unlock the buttons, and the backlight will turn on. 2. Long press M button for 5s to switch between test mode and decode mode after unlocked. During test mode, the first line of LCD will show: TEST MODE. Use test mode to verify RGBW Pixel functionality. Duirng decoder mode, the first line of LCD shows: DECODER MODE. Use decoder mode when connecting to a Controller and for final installation and customization. The second line of the LCD Display shows the current setting and value. Note: 1 Pixel = 1 Cut Increment MODE TABLE SETTING LCD DISPLAY VALUE RANGE DESCRIPTION Built-in Programs TEST MODE MODE NO.: 1-26 See Program Table below Program Speed TEST MODE RUN SPEED: 0-7 0: fast, 7: slow DMX Address DECODER MODE DMX ADDRESS: 1-512 Address of the starting point/Pixel of a program DMX Signal RGB DECODER MODE DMX RGB SEQ: RGB, BGR, etc. N/A Pixel Quantity IC TYPE Color Pixel Merging / Pixel Size DECODER MODE PIXEL QTY: DECODER MODE IC TYPE: DECODER MODE COLOR: DECODER MODE PIXEL MERGE: 1-170(RGB), 1-128(RGBW) 2903, 8903, 2904, 8904 MONO, DUAL, RGB, RGBW Number of Pixels to follow a program 2903: N/A, 2904: for RGBW, 8903: N/A, 8904: N/A MONO: N/A, DUAL: N/A, RGB: N/A, RGBW: for RGBW 1-100 Number of Pixels to merge together RGB Sequence DECODER MODE LED RGB SEQ: RGBW, BGRW, etc. Sequence of RGBW, 24 possible combinations Integral Control DECODER MODE ALL CONTROL: YES, NO Yes: Merge all Pixels No: Maintain individual Pixels or Merged Pixels Reverse Control DECODER MODE REV-CONTROL: YES, NO Reverse program order Overall Brightness DECODER MODE BRIGHTNESS: 1-100 1: dimmest setting 100: brightest setting PROGRAM TABLE PROGRAM NO. 1 2 3 4 5 6 7 8 9 PROGRAM DESCRIPTION Solid color: Red Solid color: Green Solid color: Blue Solid color: Yellow Solid color: Purple Solid color: Cyan Solid color: White RGB change Full color change PROGRAM NO. 10 11 12 13 14 15 16 17 18 PROGRAM DESCRIPTION RGB fading Full color fading Red chase with trail Green chase with trail Blue chase with trail White chase with trail RGB chase with trail Rainbow chase with trail RGB chasing and fading REV0.1 08012022 2 / 2 7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 info@luminii.com www.luminii.com Decrease Value NOTE: When connected to a controller, DMX512 Signal Decoder will stay in "Decoder Mode". NOTE: The actual maximum control pixels of the controller are 1360 (2903) ,1024 (2904). Please set the pixel and pixel combination value according to the actual situation, and DO NOT exceed the maximum. NOTE: For Program Table Change: no fading/dimming between color changes Fade: fade/dim between color changes Chase: change pixel by pixel Chase with Trail: change pixel by pixel with fading between PROGRAM NO. PROGRAM DESCRIPTION 19 Red chasing green, chasing blue 20 Orange chasing purple, chasing cyan 21 Rainbow chase (7 colors) 22 Random twinkle: white over red 23 Random twinkle: white over green 24 Random twinkle: white over blue 25 White fading 26 Off *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE