LEDYi Lighting PR RGB2 3x10A 3v1 RGB/CCT/Dimming 3 Channel LED RF Controller Owner's Manual

Match with RF 2.4G single zone or multiple zone single color, dual color, and RGB/RGBW remote control.
One RF controller accepts up to 10 remote control.

4096 levels 0-100% dimming smoothly without any flash.
When using RGB light, built-in 10 dynamic modes, include jump or gradual change style.

Auto-transmitting function: The Controller automatically transmits a signal to another controller with a 15m control distance.
Synchronize on multiple controllers.

Technical Parameters

Input and Output
Input voltage	12-36VDC
Input current	30.5A
Output voltage	3 x (12-36)VDC
Output current	3CH,10A/CH
Output power	360-1080W(12-36V)
Output type	Constant voltage

Environment
Operation temperature	Ta: -30 OC ~ +55 OC
Case temperature (Max.)	T c: +85OC
IP rating	IP20

Warranty and Protection
Warranty	2 years
Protection	Reverse Polarity

Dimming data

Input signal Control distance	RF 2.4GHz 15m(Barrier-free space)
Dimming gray scale	4096 (2^12) levels
Dimming range	0 -100%
Dimming curve	Logarithmic
PWM Frequency	750Hz (default)

Safety and EMC
EMC standard (EMC)	EN301 489, EN 62479
Safety standard(LVD)	EN60950
Radio Equipment(RED)	EN300 328
Certification	CE,EMC, LVD,RED

Weight
Net weight	0.240kg
Gross weight	0.259kg

Mechanical Structures and Installations

Wiring Diagram

Match Remote Control (two match ways)

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key

Match:
Short press the match key, and immediately press the on/off key (single zone remote) or zone key (multiple zone remote) of the remote. The LED indicator fast flash a few times means match is successful.

Delete:
Press and hold the match key for 5s to delete all matches, The LED indicator fast flash a few times means all matched remotes were deleted.

Use Power Restart

Match:
Switch off the power, then switch on power again, and immediately short press the on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful.

Delete:
Switch off the power, then switch on power again, and immediately short press the on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted.

RGB Dynamic mode list

Dual color control

CH1=Warm white LED

CH2=Cool white LED

Each channel can supply up to 240W(@24V) and the white balance can be controlled as such:

Color temperature	Cool white	Neutral white	Warm white
Power distribution	CH1=0W,CH2=240W	CH1=120W,CH2=120W	CH1=240W,CH2=0W

Malfunctions analysis & troubleshooting

Malfunctions	Causes	Troubleshooting
No light	1. No power. 2. Wrong connection or insecure.	1. Check the power. 2. Check the connection.
Wrong color	1. Wrong connection of R/G/B wires.	1. Reconnect R/G/B wires.
Uneven intensity between front and rear,with voltage drop	1. Output cable is too long. 2. Wire diameter is too small. 3. Overload beyond power supply capability. 4. Overload beyond controller capability.	1. Reduce cable or loop supply. 2. Change wider wire. 3. Replace higher power supply. 4. Add power repeater.
No response from the remote	1. The battery has no power. 2. Beyond controllable distance. 3. The controller did not match the remote.	1. Replace battery. 2. Reduce remote distance. 3. Re-match the remote.

Documents / Resources

LEDYi Lighting PR RGB2 3x10A 3v1 RGB/CCT/Dimming 3 Channel LED RF Controller [pdf] Owner's Manual
PR RGB2 3x10A 3v1 RGB CCT Dimming 3 Channel LED RF Controller, PR RGB2 3x10A 3v1, RGB CCT Dimming 3 Channel LED RF Controller, CCT Dimming 3 Channel LED RF Controller, Dimming 3 Channel LED RF Controller, 3 Channel LED RF Controller, LED RF Controller, RF Controller, Controller

References

User Manual

LEDYi Lighting PR RGB2 3x10A 3v1 RGB/CCT/Dimming 3 Channel LED RF Controller

Features