Routing Switcher
User Manual
Version 0.3.1
Chapter 1 System Requirements
1.1 Operating System Requirements
◼ Windows 10 (after ver. 1709)
◼ Windows 11
1.2 System Hardware Requirements
| Item | Requirements |
| CPU | Intel® Core™ i3 or later, or equivalent AMD CPU |
| GPU | Integrated GPU(s) or Discrete Graphic(s) |
| Memory | 8 GB of RAM |
| Free Disk Space | 1 GB free disk space for installation |
| Ethernet | 100 Mbps network card |
Chapter 2 How to Connect
Make sure the computer, OIP-N Encoder/Decoder, Recording System and VC cameras are connected in the same network segment.
Chapter 3 Operation Interface
3.1 Login Screen
| No | Item | Function Descriptions |
| 1 | Username / Password | Please enter user account/password (default: admin/admin) For initial login, you need to enter a new account, password and emailaddress to create account information  |
| 2 | Remember password | Save username and password. When you log in next time, there is no need to re-enter them |
| 3 | Forgot Password | Enter the email address you entered when registered to reset your password |
| 4 | Language | Language of the software – English is available |
| 5 | Login | Log in to the administrator screen on the website |
3.2 Configuration
3.2.1 Source
| No | Item | Function Descriptions |
| 1 | Scan | Search for devices in the LAN; RTSP/NDI streaming supported By default, the normal mode can search for RTSP. If you need to search for NDI, please go to the Discovery Settings page to configure it |
| 2 | Discovery Settings | Search for the streaming in the LAN (multiple selections supported) Select NDI to configure the following settings:◼ Group Name: Enter the group location ▷ The string can contain commas (,) to distinguish different groups ▷ The maximum string length is 127 characters ◼ Discovery Server: Enable/Disable Discovery Server ◼ Server IP: Enter the IP address |
| 3 | Add | Manually add the signal source ◼ Name: Device Name◼ Location: Device Location ◼ Stream Protocol: signal source RTSP/SRT (Caller)/HLS/MPEG-TS over UDP ◼ URL: The streaming address ◼ Authentication: By enabling, you can set the account/password |
| 4 | Export | Export configuration data, which can be imported into other computers |
| 5 | Import | Import configuration data, which can be imported from other computers |
| 6 | Delete | Delete the selected streaming, with support for deleting multiple selections at once |
| 7 | Show favorites only | Only the favorites will be shown Click the asterisk (  ) in the lower left corner of the preview screen to add the device to your favorites |
| 8 | IP Prompt | Show the last two digits of the IP address |
| 9 | Source Information | Clicking the preview screen will show the source information Click  to open the window for advanced function setting The displayed items may vary depending on the model of the source ◼ User Name: Username◼ Password: Password ◼ Stream Audio From (Stream Audio Source) ▷ Encode Sample Rate: Set encode sample rate ▷ Audio Volume: Adjust Audio Volume ◼ Audio in Type: Audio in Type (Line In/MIC In) ▷ Encode Sample Rate: Encode sample rate (48 KHz) ▷ Audio Volume: Adjust audio volume ◼ Audio Out Source ▷ Audio Volume: Adjust audio volume ▷ Audio Delay Time: Set the audio signal delay time (0 ~ 500 ms) ◼ Factory Reset: Reset all configurations to factory default settings |
3.2.2 Display
| No | Item | Function Descriptions |
| 1 | Scan | Search for devices in the LAN |
| 2 | Add | Manually add the display source |
| 3 | Export | Export configuration data, which can be imported into other computers |
| 4 | Import | Import configuration data, which can be imported from other computers |
| 5 | Delete | Delete the selected streaming, with support for deleting multiple selections at once |
| 6 | Show favorites only | Only the favorites will be shown Click the asterisk ( ) in the lower left corner of the preview screen to add the device to your favorites |
| 7 | IP Prompt | Show the last two digits of the IP address |
| 8 | Display Information | Clicking the preview screen will show the device information. Click to open the window for advanced function setting. The displayed items may vary depending on the model of the source ◾ User Name: Username◾ Password: Password ◾ Video Output: Output Resolution ◾ CEC: Enable/Disable the CEC function ◾ HDMI Audio From: Set the HDMI audio source ▷ Audio Volume: Adjust audio volume ▷ Audio Delay Time: Set the audio signal delay time (0 ~ -500 ms) ◾ Audio in Type: Audio in Type (Line In/MIC In) ▷ Encode Sample Rate: Set Encode sample rate ▷ Audio Volume: Adjust audio volume ◾ Audio Out: Audio output source ▷ Audio Volume: Adjust audio volume ▷ Audio Delay Time: Set the audio signal delay time (0 ~ -500 ms) ◾ Factory Reset: Reset all configurations to factory default settings |
3.2.3 User
Function Descriptions
Display information of the administrator/user account
◼ Account: Supporting 6 ~ 30 characters
◼ Password: Supporting 8 ~ 32 characters
◼ User Permissions:
| Function Items | Admin | User |
| Configuration | V | X |
| Routing | V | V |
| Maintenance | V | V |
3.3 Routing
3.3.1 Video
| No | Item | Function Descriptions |
| 1 | Signal source list | Show the source list and the display list Select a signal source and drag it to the display list |
| 2 | Show favorites only | Only the favorites will be shown Click the asterisk ( ) in the lower left corner of the preview screen to add the device to your favorites |
| 3 | IP Prompt | Show the last two digits of the IP address |
3.3.2 USB
| No | Item | Function Descriptions |
| 1 | USB Extender | To enable/disable the OIP-N60D USB Extender mode ● means On; a blank means Off |
| 2 | Show favorites only | Only the favorites will be shown Click the asterisk ( ) in the lower left corner of the preview screen to add the device to your favorites |
| 3 | IP Prompt | Show the last two digits of the IP address |
3.4 Maintenance
| No | Item | Function Descriptions |
| 1 | Version Update | Click [Update] to check the version and update it |
| 2 | Language | Language of the software – English is available |
3.5 About
Function Descriptions
Display software version information. For technical support, please scan the QRcode at the bottom right.
Chapter 4 Troubleshooting
This chapter describes problems you may encounter while using Routing Switcher. If you have questions, please refer to related chapters and follow all the suggested solutions. If the problem still occurs, please contact your distributor or the service center.
| No. | Problems | Solutions |
| 1 | Unable to search devices | Please make sure that the computer and the device are connected in the same network segment. (Refer to Chapter 2 How to Connect) |
| 2 | The operating steps in the manual are not consistent with the software operation |
The software operation may be different from the description in the manual due to functional improvement. Please make sure you’ve updated your software to the latest version. ◾ For the latest version, please go to the Lumens official website > Service Support > Download Area. https://www.MyLumens.com/support |
Copyright Information
Copyrights © Lumens Digital Optics Inc. All rights reserved.
Lumens is a trademark that is currently being registered by Lumens Digital Optics Inc.
Copying, reproducing or transmitting this file is not allowed if a license is not provided by Lumens Digital Optics Inc. unless copying this file is for the purpose of backup after purchasing this product.
In order to keep improving the product, the information in this file is subject to change without prior notice.
To fully explain or describe how this product should be used, this manual may refer to names of other products or companies without any intention of infringement.
Disclaimer of warranties: Lumens Digital Optics Inc. is neither responsible for any possible technological, editorial errors or omissions, nor responsible for any incidental or related damages arising from providing this file, using, or operating this product.
Documents / Resources
 |
Lumens OIP-N Encoder Decoder [pdf] User Manual OIP-N Encoder Decoder, Encoder Decoder, Decoder |