TEMTOP AIRING-2000 Handheld Particle Counter Particulate Monitor Instruction Manual

Power ON
Press and hold the power button for 2 seconds to turn on the detector. After initialization, the instrument enters the default interface without starting the measurement to save power.

Start Detection
Press the measure/wait button to start detection, displaying real-time data of all parameters. The instrument defaults to continuous sampling. Press the same button to pause sampling.
Switch Measurement Items
The default PM2.5 data is displayed in the main view box. Use the up or down buttons to switch between measurement items displayed in the main view box.

Setting Menu
Press the menu button to enter the menu screen. Use the up or down buttons to toggle between options, and then press the OK button to confirm your choice for viewing or changing settings.
System Setting
In the system setting interface, navigate to MENU->Setting to set time, sample, backlight adjustment, and language preferences. Use the up or down buttons to switch options and press OK to enter.”
1. Time Setting
  In the time setting interface, use the buttons to adjust time settings. Press OK to save the settings when finished.
2. Sample Setting
  In the sample setting interface, set Temperature Unit, Storage Interval, and Warning Settings as needed.

Introduction

The AIRING-2000 is a small, lightweight, battery-powered, multi-functional handheld particulate mass monitor. Three channels output counts of 0.3µm, 0.5µm, and 1.0µm, particulate matter. It also features PM2.5, PM10, TSP, temperature and humidity, and historical data.

The large screen display and seven-button operation are simple and efficient, making it suitable for quick tests in various scenarios. The built-in high-performance lithium battery allows the instrument to run continuously for at least 4 hours. Meanwhile, the AIRING-2000 has 32GB of built-in storage so that test data can be viewed directly on the display or use a USB stick to export to a PC via the USB port for viewing and analysis.

Important!

Do not expose the detector to heavily contaminated environments for long periods, as this can damage the sensor.
Do not come into contact with organic solvents, whichinclude silica gel and other adhesives, paintings, drugs, oil and high-concentration gases.

Do not use the detector in a humid environment to maintain detection accuracy.
Do not cover the air inlet/outlet when using the detector.

Do not dismantle the unit yourself. In the event of a defect, contact your dealer instead, who will liaise with the service center and, if necessary, send the device in for repair.
Children should only use this device under adult supervision. Keep packaging materials, such as plastic bags and plastic wrap, out of the reach of children as they present a choking hazard.

Overview

Temperature & Humidity Detection Channel

LCD Screen
Power Button

Back Button
OK Button

Intake Duct
USB Port
TYPE-C Port
Measure/Wait Button
Menu Button
Up Button
Down Button
Air Outlet
Bracket Hooks

Specifications

Model	AIRING-2000
Dimensions	228x115x70mm(9×4.5×2.8 in)
Battery Capacity	3500mAh
Battery Life	＞4h
Charging Output	DC5V, 2A
PM2.5	Range: 0-9999.9µg/m3 Resolution: 0.1µg/m3 Accuracy: ±10µg/m3 (0-100µg/m3), ±10% (>100µg/m3)
PM10	Range: 0-9999.9µg/m3 Resolution: 0.1µg/m3 Accuracy: ±10µg/m3 (0-100µg/m3), ±10% (>100µg/m3)
TSP	Range: 0-9999.9µg/m3 Resolution: 0.1µg/m3 Accuracy: ±10µg/m3 (0-100µg/m3), ±10% (>100µg/m3)
0.3µm, 0.5µm, 1.0µm	Range: 0-999999 P/L Resolution: 1 P/L Accuracy: ±30%
Temperature	Range: 0-50°C (32-122°F) Resolution: 0.1°C Accuracy: ±0.5°C (±0.9°F)
Humidity	Range: 0-90%RH Resolution: 0.1% Accuracy: ±5%RH

Note: The above data are from Temtop Laboratory.

Range: 0-9999.9μg/m3 Resolution: 0.1μg/m3
Accuracy: ±10μg/m3 (0-100μg/m3), ±10% (>100μg/m3)
Range: 0-9999.9μg/m3 Resolution: 0.1μg/m3
Accuracy: ±10μg/m3 (0-100μg/m3), ±10% (>100μg/m3)

Warning!

Indoor use: Keep the room/area airtight for 10 minutes to obtain more accurate results.
If battery level shows , please charge the detector promptly to avoid effects during use (also chargeable when turned off). 76.5 °F 54.4%RH

Power ON

Press and hold button for 2 seconds to turn on the detector.
After initialization, the instrument enters the default interface.

lt will not start the measurement by default to save the power (Fig.2).
Press to start detection, and it will display the real-time data of all parameters. The instrument defaults to continuous sampling. During the sampling process, you can press to pause sampling (Fig.3).
The instrument default PM2.5 data is displayed in the main view box, press or to switch the measurement items displayed in the main view box (Fig.4).

Setting Menu

Press to enter the menu screen, then press or to toggle between options.

Press to confirm your choice to view or change settings (Fig.5).

MENU options are as follows:

Menu	Display as…	Description
System Setting	Setting	Set system time, sampling, backlight, and language.
System Calibration	Calibration	Calibrate zero, and k-Factor.
Data History	History	Query, download and delete the data.
System Information	Information	Display system information.

System Setting
In the system setting interface MENU->Setting, you can set time, sample, backlight adjustment, and language. Press or to switch the options (Fig.6) and press to enter.

Time Setting
Press the key to enter the time setting interface, press the key to switch the option, press the or key to increase or decrease the value, switch to the Save option when the setting is completed, press thekey to save the setting (Fig. 7).

Sample Setting
In the system setting interface MENU->Setting, press or to switch to the Sample Setting, and then press to enter the sample setting interface (Fig.8). In the sample setting interface you can set the Temperature Unit, Storage Interval and Warning Setting.

Temperature Unit

In the system setting interface MENU->Setting->Sample.
Press to enter the Temperature Unit interface.
Press or to select °C or °F.

Then press to switch to Save and pressto save (Fig.9).

Storage Interval

In the system setting interface MENU->Setting->Sample.
Press or to switch to the Storage Interval, and Press to enter.
The storage interval 1min, 2min, 5min, 10min, 15min, 30min and 60min is optional.

Press or key to switch the storage interval.
Then press to switch to Save and press to save (Fig.10).

Warning Setting

In the system setting interface MENU->Setting->Sample.
Press or to switch to the Warning Setting, and Press to enter. Press to select the on or off alarm switch.

Press or to select PM2.5, PM10, TSP, 0.3μm, 0.5μm, and 1.0μm, press to select the modification item and press to toggle the modified value, then press or to modify the alarm threshold.
Press or to switch to Save when the setting is complete and press to save (Fig.11).

Note: The product factory default settings will be restored when the default settings are made.

Backlight Adjustment

In the system setting interface MENU->Setting.

Press or to switch to the Backlight Adjustment, and press to enter.
Press or to select 1, 2 and 3.
Then press to switch to Save and press to save (Fig.12).

Note: The factory default screen backlight level is 3.

Language Setting

In the system setting interface MENU->Setting.
Press or to switch to the Language Setting, and press to enter.
Press or to select English or 中文.

Then press to switch to Save and press to save (Fig.13).

System Calibration

In the system calibration interface MENU->Calibration, you can operate Zero Calibration and K-Factor Calibration.
Press or to switch the option and press to enter (Fig.14).

Zero Calibration

Under the Zero Calibration interface, press to start calibrating.
It takes about 90 seconds countdown. After the countdown finishes, the display prompts a reminder to confirm the calibration finishes successfully and will return to the MENU-Calibration interface automatically (Fig. 15).

K-Factor Calibration

Make sure the instrument is in a stable environment.

Press to perform a K-factor mass concentration calibration. The product will turn on the pump and collect data for 60 seconds, then proceed to the K Factor Mass Concentration Calibration screen.
Press or to switch the cursor, press to select the modification item, and press to toggle the modified value, then press or to increase or decrease the value.
Press or to switch to calibrate after the setting is completed, press to calibrate (Fig.16).

Note: The product factory default settings will be restored when the default settings are made.

Data History

In the data history interface MENU->History, you can operate Data Query, History Download and History Deletion.
Press or to switch the option and press to enter (Fig.17).

Data Query

In the query interface, you can press month data. Press to enter the month selection interface, by default the system will automatically recommend the current month.
If you need data for other months, you can press or to increase or decrease the value. When finished, press to switch to the query and press to enter the query (Fig.18).

History Download
In the History Download interface, insert a USB device such as a USB flash drive or card reader into the USB port of the monitor, If the USB device is successfully connected, press to download the data (Fig. 19).

After downloading the data, unplug the USB device and insert it into the computer to find a folder prefixed with the product serial number, for example, “TT1246070001-062120241754”. You can view and analyze the data now. If the USB device fails to connect or there is no USB device connected, the display will prompt a reminder. Please reconnect it or try again later (Fig. 20).

History Deletion
In the History Deletion interface, data can be deleted by month or all. Press or to switch options and press to enter (Fig. 21).

By Month
For the Monthly Data interface, the current month will auto display by default. lf you need to delete other months, please press switching to the year and month options, then press or to increase or decrease the value. After complete, press to switch to Delete and pressto complete the delete(Fig.22).
All Data
For the All Data screen, the display will prompt ‘Are you sure you want to delete the data?’ Press to confirm the deletion (Fig. 23). Wait for the deletion to complete, if the data has been successfully deleted the display will prompt a reminder and automatically return to the Menu-History screen.

System Infomation
The System Infomation interface shows the following information (Fig.24)

Power OFF
Press and hold for 2 seconds to turn off the monitor (Fig.25).

What’s Included

Detector x 1
USB Cable x 1

User Manual x 1
Calibration Certificate x 1
Battery Charger (Includes 4 adapters)* x 1

Battery Charger Schematic and Operation Example:

Example:

Installation:
Hold the “Snap Switch” in your left hand and turn it in the “LOCK” direction with your right hand.
Removal:
Hold the “Snap Switch” in your left hand and turn it in the “OPEN” direction with your right hand.

Troubleshooting

Failure	Possible Causes	Solution
Noise	The flow is excessive	Flow calibration
Noise	The pump is faulty	Send to the service center
Cannot be turned on, no display	Battery discharged	Charge the battery for 3.5 h
Cannot be turned on, no display	The battery is faulty	Send to the service center
Display is on, but pump does not run	Low battery level	Charge the battery for 3.5 h
Display is on, but pump does not run	The pump is faulty	Send to the service center
Detected value is not reliable	Flow deviation	Flow calibration
	Inlet screen clogged	Check the inlet screen
	Contamination inside the monitor	Replace the filter element
	Contamination inside the monitor	Send to the service center
Unable to charge the battery	The battery is faulty	Send to the service center
Unable to charge the battery	Charger failure	Contact the service center

Warranty

Temtop warrants the included detector for 1 year from the date of original purchase. The item can be exchanged or returned within 30 days if the defect is not caused by artiﬁcial damage.

Item	Warranty Period
Detector	1 year included
Accessories	N/A

Before return or delivery for repair, please check if the following √ items are ready:

	Detector & Accessories	Complete Package	Proof of Purchase*	Gift (if any)
Return	√	√	√	√
Exchange	√	√	√
Repair	√		√

* Including invoice, order number and etc.

Temtop warranty does NOT include:

Malfunction or damages caused by artiﬁcial damage or modiﬁcation.
Other deliberate damages.

Damage caused by natural events.

Elitech Technology, Inc

2528 Qume Dr, Ste 2 San Jose, CA 95131 USA

Tel: (+1) 408-898-2866
Facebook: www.facebook.com/temtopus
Instagram: www.instagram.com/temtopaqm/

youtube: www.youtube.com/
@Temtopus linkedin: www.linkedin.com/company/temtop-us/X:x.com/temtopus48285
Sales: sales@temtopus.com
Website: www.temtopus.com

Elitech Brazil Ltda

R.Dona Rosalina,90-Lgara, Canoas-RS 92410-695,Brazil
Tel: (+55)51-3939-8634
Sales: brasil@e-elitech.com
Website: www.elitechbrasil.com.br

Elitech (UK) Limited

Unit 13 Greenwich Business Park, 53 Norman Road,London, SE10 9QF Tel: (+44)208-858-1888
Youtube: @elitech_uk
Instagram: @elitechuk_
Facebook: @hvaccontrol
Sales: sales@elitecheu.com
Website: www.temtop.co.uk

Made In China

FAQ

Q: How do I charge the AIRING-2000?
A: The AIRING-2000 can be charged when turned off using a DC5V, 2A charger via the TYPE-C port.

Q: What is the battery life of the AIRING-2000?
A: The battery capacity of AIRING-2000 is 3500mAh, providing a battery life of approximately 4 hours.

Documents / Resources

TEMTOP AIRING-2000 Handheld Particle Counter Particulate Monitor [pdf] Instruction Manual
AIRING-2000 Handheld Particle Counter Particulate Monitor, AIRING-2000, Handheld Particle Counter Particulate Monitor, Particle Counter Particulate Monitor, Counter Particulate Monitor, Particulate Monitor, Monitor

References

User Manual

TEMTOP AIRING-2000 Handheld Particle Counter Particulate Monitor

Product Usage Instructions