Surenoo SRG1010B-1280800 Series RGB Interface TFT LCD Module
GENERAL INFORMATION
Item of general information |
Contents |
Unit | |
LCD Display Size (Diagonal) |
10.1 |
inch |
|
Module Structure |
LCD Display + CTP Touch + PCB | – | |
LCD Display Type | TFT/TRANSMISSIVE |
– |
|
LCD Display Mode |
Normally Black | – | |
Recommended Viewing Direction | Free |
– |
|
Gray inversion Direction | Free |
– |
|
Module size (W×H×T) |
A1: 229.46×149.10×4.90 | mm | |
A2: 255.00×172.60×4.60 |
mm |
||
Active area (W×H) |
216.96×135.60 | mm | |
Number of pixels (Resolution) | 1280RGB×800 |
pixel |
|
Pixel pitch (W×H) |
0.1695×0.1695 | mm | |
Color Pixel Arrangement | RGB Stripe |
– |
|
Module Interface Type |
LCD | RGB Interface | – |
CTP |
I2C interface |
– | |
Module Input voltage | 5.0V | V | |
Module Power consumption | 600(Typ.) |
mA |
|
Color Numbers |
16.7M | – | |
Backlight Type | White LED |
– |
EXTERNAL DIMENSIONS
SRG1010B1-1280800
SRG1010B2-1280800
ABSOLUTE MAXIMUM RATINGS
Parameter of absolute maximum ratings |
Symbol |
Min |
Max |
Unit |
Operating temperature | Top | -10 | 60 |
℃ |
Storage temperature |
Tst | -20 | 70 | ℃ |
Humidity | RH | – | 90%(Max 60℃) |
RH |
Note: Absolute maximum ratings means the product can withstand short-term, not more than 120 hours. If the product is a long time to withstand these conditions, the life time would be shorter.
ELECTRICAL CHARACTERISTICS(DC CHARACTERISTICS
Parameter of DC characteristics |
Symbol | Min. | Typ. | Max. |
Unit |
PCB operating voltage |
VCC5V | – | 5.0 | – | V |
LCD I/O operating voltage | VDD | 2.3 | 2.5 | 2.7 |
V |
Input voltage ‘H’ level |
VIH | 0.8*VDD | – | VDD | V |
Input voltage ‘L’ level | VIL | VSS | – | 0.2*VDD |
V |
Output voltage ‘H’ level |
VOH | VDD-0.4 | – | VDD | V |
Output voltage ‘L’ level | VOL | VSS | – | VSS+0.4 |
V |
BACKLIGHT CHARACTERISTICS
Item of backlight characteristics | Symbol | Min. | Typ. | Max. | Unit | Remark |
Forward Voltage |
Vf | 8.4 | 9.3 | 10.2 | V |
Note1 |
Forward Current |
If | – | 260 | – | mA | – |
Number of LED | – | – | 3*13=39 | – | Piece |
– |
LED Connection mode |
P/S | – | Serial/Parallel | – | – | – |
Lifetime of LED | – | – | 10000 | – | hour |
Note 2 |
Note:
- Note1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and If=260mA.
- Note 2: The LED lifetime define as the estimated time to 50% degradation of initial luminous. The LED lifetime could be decreased if operating If is lager than 200mA.
- Backlight control via the BL_CTR pin or PWM signal.
- Backlight circuit:
Backlight Circuit
CTP CHARACTERISTICS
Item of CTP characteristics |
Specification |
Unit |
Remark |
Panel Type |
Glass Cover + Glass Sensor | – |
– |
Resolution |
1280 × 800 | pixel | – |
Surface Hardness | 6H | – |
– |
Transparency |
≥86% | – | – |
Driver IC | GT9271 | – |
– |
Interface Type |
I2C | – | – |
Support Points | 10 | – |
– |
Sampling Rate |
20~100 | Hz | – |
Supply voltage | 3.3 | V |
– |
ELECTRO-OPTICAL CHARACTERISTICS
Item of electro-optical characteristics |
Symbol | Condition | Min. | Typ. | Max. | Unit | Remark |
Note |
|
Response time |
Tr+Tf | θ=0![]() Ta=25℃ |
– | 25 | 50 | ms | FIG 1. | 4 | |
Contrast Ratio |
CR |
– |
600 |
– |
– |
FIG 2. |
1 |
||
Luminance uniformity |
|
– |
80 | – | % | FIG 2. | 3 | ||
Surface Luminance | Lv | – | 300 | – | cd/m2 | FIG 2. |
2 |
||
CIE (x, y) chromaticity |
White |
White x |
θ=0 |
0.27 |
0.31 | 0.35 | – | FIG 2. | 5 |
White y |
0.28 |
0.32 |
0.36 |
||||||
Viewing angle range |
![]() |
CR ![]() |
75 | 85 | – | deg | FIG 3. | 6 | |
|
75 |
85 |
– |
deg |
|||||
|
75 | 85 | – | deg | |||||
![]() |
75 | 85 | – |
deg |
|||||
NTSC ratio | – | – | – | 50 | – | % | – |
– |
Note 1. Contrast Ratio(CR) is defined mathematically by the following formula. For more information see FIG 2.:
Note 2. Surface luminance is the LCD surface from the surface with all pixels displaying white. For more information see FIG 2.
Lv=Average Surface Luminance with all white pixels (P1,P2,P 3,P4, P5,P6,P7,P8,P9)
Note 3. The uniformity in surface luminance(SWHITE)is determined by measuring luminance at each test position 1 through 9, and then dividing the maximum luminance of 9points luminance by minimum luminance of 9 points luminance. For more information see FIG 2.
Note 4. The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON ) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF ) is the time between photo detector output intensity changed from 10% to 90%. For more information see FIG 1.
Note 5. CIE (x, y) chromaticity ,The x,y value is determined by screen active area position 5. For more information see FIG 2.
Note 6. Viewing angle is the angle at which the contrast ratio is greater than a specific value. For TFT module, the specific value of contrast ratio is 10.The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG 3.
Note 7. For Viewing angle and response time testing, the testing data is base on
Autronic-Melchers’s ConoScope. Series Instruments. For contrast ratio, Surface Luminance, Luminance uniformity and CIE,the testing data is base on BM-7 photo detector. Note 8. For TN type TFT transmissive module, Gray scale reverse occurs in the direction of panel viewing angle.
FIG.1. The definition of Response Time
FIG.2. Measuring method for Contrast ratio, surface luminance, Luminance uniformity,
CIE (x , y) chromaticity
A : H/6 ;
B : V/6 ;
H,V : Active Area(AA) size
Measurement instrument: BM-7; Light spot size=5mm, 350mm distance from the LCD surface to detector lens.
FIG.3. The definition of viewing angle
INTERFACE DESCRIPTION
NO. |
Symbol | I/O |
DESCRIPTION |
1~2 |
VCC5V | P | Module Power supply (5V Typ.) |
3~10 | R0~R7 | I |
8bit digital Red data input(R0:LSB; R7:MSB) |
11 |
GND | P | Power ground |
12~19 | G0~G7 | I |
8bit digital Green data input(G0:LSB; G7:MSB) |
20 |
GND | P | Power ground |
21~28 | B0~B7 | I |
8bit digital Blue data input(B0:LSB; B7:MSB) |
29 |
GND | P | Power ground |
30 | DCLK | I |
Clock signal. |
31 |
HSYNC |
I | Horizontal Sync input. |
32 | VSYNC | I |
Vertical Sync input. |
33 |
DEN |
I | Data input Enable. |
34 | BL_CTR | I |
Backlight control pin |
35 | TP_RST | I |
CTP external reset signal, Low is active |
36 |
TP_SDA |
I/O | CTP I2C data input and output |
37 |
NC | – |
No connection |
38 | TP_SCL | I |
CTP I2C clock input |
39 |
TP_INT | I/O | CTP External interrupt to the host |
40 | NC | – |
No connection |
Application Note:
For RGB interface input:
- For RGB565 Input Format: R3~R7, G2~G7, B3~B7 be used.
- For RGB666 Input Format: R2~R7, G2~G7, B2~B7 be used
INPUT TIMING
RGB Input Timing Table
Parameter |
Symbol | Value | Unit | ||
Min. | Typ. |
Max. |
|||
DCLK frequency@ Frame rate=60Hz |
DCLK | 68.9 | 71.1 | 73.4 |
MHz |
Horizontal display area |
thd | 1280 | DCLK | ||
1 Horizontal Line | th | 1340 | 1440 | 1470 |
DCLK |
HSYNC pulse width |
thpw | – | 10 | – | DCLK |
HSYNC Back Porch(Blanking) | thb | – | 80 | – |
DCLK |
HSYNC Front Porch |
thfp | – | 70 | – | DCLK |
Vertical display area | tvd | 800 |
H |
||
VSYNC period time |
tv | 815 | 823 | 833 | H |
VSYNC pulse width | tvpw | – | 3 | – |
H |
VSYNC Back Porch(Blanking) |
tvb | – | 10 | – | H |
VSYNC Front Porch | tvfp | – | 10 | – |
H |
LVDS Data Input Format
RELIABILITY TEST CONDITIONS
No. |
Test Item |
Test Condition |
1 |
High Temperature Storage | 70℃/120 hours |
2 | Low Temperature Storage |
-20℃/120 hours |
3 |
High Temperature Operating | 60℃/120 hours |
4 | Low Temperature Operating |
-10℃/120 hours |
5 |
Temperature Cycle Storage |
-10℃(30min.)~25(5min.)~60℃(30min.)×10 cycles |
A、Inspection after test:
Inspection after 2~4 hours storage at room temperature, the sample shall be free from defects:
B、Remark:
|
INSPECTION CRITERION
This specification is made to be used as the standard of acceptance/rejection criteria for TFT-LCD/IPS TFT-LCD module product, and this specification is applicable only in the case that the size of module equal to or exceed than 4.3 inch.
Sample plan
Sampling plan according to GB/T2828.1-2003/ISO 2859-1:1999 and ANSI/ASQC
Z1.4-1993,normal level 2 and based on:
Major defect: AQL 0.65
Minor defect: AQL 1.5
Inspection condition
Viewing distance for cosmetic inspection is about 30cm with bare eyes, and under an environment of 20~40W light intensity, all directions for inspecting the sample should be within 45°against perpendicular line. (Normal temperature 20~25℃and normal humidity 60 ±15%RH )
Definition of Inspection Item.
A, Definition of inspection zone in LCD.
Zone A: character/Digit area
Zone B: viewing area except Zone A (Zone A + Zone B=minimum Viewing area)
Zone C: Outside viewing area (invisible area after assembly in customer’s product)
Fig.1 Inspection zones in an LCD
Note: As a general rule, visual defects in Zone C are permissible, when it is no trouble for quality and assembly of customer’s product.
B, Definition of some visual defect
Bright dot | Because of losing all or part function, bad pixel dots appear bright and the size is more than 50% of one dot in which LCD panel is displaying under black pattern. |
Dark dot | Dots appear dark and unchanged in size in which LCD panel is displaying under pure red, green, blue picture, or pure whiter picture. |
Major Defect
Item No. |
Items to be inspected |
Inspection standard |
Classification of defects |
1 |
Functional defects |
|
major |
2 |
Missing |
Missing component |
|
3 | Outline dimension |
Overall outline dimension beyond the drawing is not allowed |
Minor Defect
Item No. |
Items to be inspected |
Inspection standard |
Classification of defects |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
1 |
Bright dot /dark dot defect |
Note: Minimum distance between defective dots is more than 5mm; Pixel dots’ function is normal, but bright dots caused by foreign material and other reasons are judged by the dot defect of 5.2. |
Minor |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
2 | ![]() |
Note:
|
Minor |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
3 |
Linear defect |
|
Minor |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
4 |
Polarizer defect |
|
Minor |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
5 |
MURA | Using 3% ND filter, it’s NG if it can be seen in R,G,B picture |
Minor |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
White/Black dot(MURA) | Visible under:ND3%;D≦0.15mm, Acceptable; 0.15mm<D≦0.5mm, N≦4;D>0.5mm, Not allowable. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||
6 |
Glass defect |
(i) Crack Cracks are not allowed.
|
Minor |
|||||||||||||||||||||||||||||||||||||||||||||||||||||
(ii) TFT chips on corner
Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. |
Minor |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||
(iii) Usual surface crack
It is only applicable to the upper glass of LCD. |
Minor |
Module Cosmetic Criteria
Item No. |
Items to be inspected | Inspection Standard |
Classification of defects |
1 |
Difference in Spec. |
Not allowable | Major |
2 | Pattern peeling | No substrate pattern peeling and floating |
Major |
3 |
Soldering defects | No soldering missing | Major |
No soldering bridge |
Major | ||
No cold soldering |
Minor |
||
4 | Resist flaw on PCB | Visible copper foil (Φ0.5 mm or more) on substrate pattern is not allowed |
Minor |
5 |
FPC gold finger | No dirt, breaking, oxidation lead to black | Major |
6 | Backlight plastic frame | No deformation, crack, breaking, backlight positioning column
breaking, obvious nick. |
Minor |
7 |
Marking printing effect | No dark marking, incomplete, deformation lead to
unable to judge |
Minor |
8 | Accretion of metallic
Foreign matter |
No accretion of metallic foreign matter (Not exceed Φ0.2mm) |
Minor |
9 |
Stain |
No stain to spoil cosmetic badly | Minor |
10 | Plate discoloring’s | No plate fading, rusting and discoloring |
Minor |
11 |
1. Lead parts |
a. Soldering side of PCB Solder to form a ‘Filet’ all around the lead. Solder should not hide the lead form perfectly. | Minor |
b. Components side(In case of ‘Through Hole PCB’) Solder to reach the Components side of PCB. |
Minor |
||
2. Flat packages |
Either ‘Toe’(A) or ‘Seal’(B)of the lead to be covered by “Filet”. Lead form to be assume over Solder.![]() |
Minor | |
3. Chips | (3/2) H ≥h ≥(1/2) H![]() |
Minor |
|
4. Solder ball/Solder splash | a. The spacing between solder ball and the conductor or solder pad h ≥0.13 mm. The diameter of solder ball d≤0.15 mm. | Minor | |
b. The quantity of solder balls or solder splashes isn’t beyond 5 in 600 mm2. | Minor | ||
c. Solder balls/Solder splashes do not violate minimum electrical clearance. | Major |
CUSTOMERS SUPPORT
Business Card
WhatsApp
LINE
WeChat
Shenzhen Surenoo Technology Co., Ltd.
www.surenoo.com
Skype: Surenoo365
Documents / Resources
![]() |
Surenoo SRG1010B-1280800 Series RGB Interface TFT LCD Module [pdf] User Manual SRG1010B-1280800 Series RGB Interface TFT LCD Module, SRG1010B-1280800 Series, RGB Interface TFT LCD Module, Interface TFT LCD Module, TFT LCD Module, LCD Module |