Surenoo logo

Surenoo SMC0700B-800480 Series MCU Interface TFT LCD Module

Surenoo SMC0700B-800480 Series MCU Interface TFT

GENERAL INFORMATION

Item of general information Contents Unit
LCD Display Size (Diagonal) 7.0 inch
 

Module Structure

LCD Display + RTP Touch + PCB

 

LCD Display + CTP Touch + PCB

 

LCD Display Type TFT/TRANSMISSIVE
LCD Display Mode Normally White
Viewing Direction 12 O’CLOCK
Gray inversion Direction 6 O’CLOCK
Module size (W×H×T) 185.00×105.00×8.45 mm
Active area (W×H) 154.21×85.92 mm
Number of pixels (Resolution) 800RGB×480 pixel
Pixel pitch (W×H) 0.1926 × 0.1790 mm
LCD Driver IC LT7381
 

 

Module Interface Type

LCD MCU 16bit/8bit interface
RTP 4-Wire Resistive Touch
CTP IIC interface
Module Input voltage 5.0V V
Module Power consumption mW
Color Numbers 16.7M
Backlight Type White LED

EXTERNAL DIMENSIONS

Surenoo SMC0700B-800480 Series MCU Interface TFT 1

ABSOLUTE MAXIMUM RATINGS

Parameter of absolute

maximum ratings

Symbol Min Max Unit
Operating temperature Top -20 70
Storage temperature Tst -30 80
Humidity RH 90%(Max 60℃) RH

Note: Absolute maximum ratings means the product can withstand short-term, not more than 120 hours. If the product is a long time to withstand these conditions, the life time would be shorter.

ELECTRICAL CHARACTERISTICS(DC CHARACTERISTICS)

Parameter of DC characteristics Symbol Min. Typ. Max. Unit
PCB operating voltage VCC5V 5.0 V
LCD I/O operating voltage VDD 3.0 3.3 3.6 V
Input voltage ‘H’ level VIH 2 3.6 V
Input voltage ‘L’ level VIL -0.3 0.8 V
Output voltage ‘H’ level VOH 2.4 V
Output voltage ‘L’ level VOL 0.4 V

BACKLIGHT CHARACTERISTICS

Item of backlight

 characteristics

Symbol Min. Typ. Max. Unit Remark
Forward Voltage Vf 8.4 9.3 9.9 V Note1
Forward Current If 140 mA
Number of LED 7*3 Piece
LED Connection mode P/S Serial
Lifetime of LED 10000 hour Note2

Note:

  • Note1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and If=140mA.
  • Note2: The LED lifetime define as the estimated time to 50% degradation of initial luminous. The LED lifetime could be decreased if operating If is larger than 140mA.

ELECTRO-OPTICAL CHARACTERISTICS

Item of electro-optical

characteristics

Symbol Condition Min. Typ.  

Max

.

Unit Remark Note
Response time Tr + Tf  

θ=0

=0

Ta=25℃

25 40 ms FIG 1. 4
Contrast Ratio CR 350 FIG 2. 1
Luminance uniformity WHITE 80 % FIG 2. 3
Surface Luminance Lv 300 cd/m2 FIG 2. 2
 

 

 

 

CIE (x, y)

chromaticity

White White x  

 

 

θ=0

=0

Ta=25℃

0.310  

 

 

 

 

 

 

 

FIG 2.

 

 

 

 

5

White y 0.33
Red Red x 0.587
Red y 0.331
Green Green x 0.344
Green y 0.571
Blue Blue x 0.146
Blue y 0.0092
 

Viewing angle range

=90(12 o’clock)  

CR  10

50 deg  

 

FIG 3.

 

 

6

=270(6 o’clock) 70 deg
=0(3 o’clock) 70 deg
=180(9 o’clock) 70 deg
NTSC ratio 50 %
  1. Note 1. Contrast Ratio (CR) is defined mathematically by the following formula. For more information see FIG 2.:Surenoo SMC0700B-800480 Series MCU Interface TFT 12
  2. Note 2. Surface luminance is the LCD surface from the surface with all pixels displaying white. For more information see FIG 2.
    Lv=Average Surface Luminance with all white pixels (P1,P2,P3,P4,P5,P6,P7,P8,P9)
  3. Note 3. The uniformity in surface luminance(WHITE)is determined by measuring luminance at each test position 1 through 9, and then dividing the maximum luminance of 9points luminance by minimum luminance of 9 points luminance. For more information see FIG 2.Surenoo SMC0700B-800480 Series MCU Interface TFT 13
  4. Note 4. Response time is the time required for the display to transition from White to black(Rise Time, Tr) and from black to white(Decay Time, Tf). For additional information see FIG 1.
  5. Note 5. CIE (x, y) chromaticity ,The x,y value is determined by screen active area position 5. For more information see FIG 2.
  6. Note 6. Viewing angle is the angle at which the contrast ratio is greater than a specific value. For TFT module, the specific value of contrast ratio is 10.The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG 3.
  7. Note 7. For Viewing angle and response time testing, the testing data is base on Autronic-Melchers’s ConoScope. Series Instruments. For contrast ratio, Surface Luminance, Luminance uniformity and CIE,the testing data is base on BM-7 photo detector.
  8. Note 8. For TN type TFT transmissive module, Gray scale reverse occurs in the direction of panel viewing angle.

FIG.1. The definition of Response Time

Surenoo SMC0700B-800480 Series MCU Interface TFT 2

FIG.2. Measuring method for Contrast ratio, surface luminance, Luminance uniformity,
CIE (x , y) chromaticity
A : H/6 ;
B : V/6 ;
H,V : Active Area(AA) size
Measurement instrument: BM-7; Light spot size=5mm, 350mm distance from the LCD surface to detector lens.

Surenoo SMC0700B-800480 Series MCU Interface TFT 3

FIG.3. The definition of viewing angle 

Surenoo SMC0700B-800480 Series MCU Interface TFT 4

INTERFACE DESCRIPTION

LCD1 Interface Description for CTP

NO. Symbol I/O DESCRIPTION
1 CS I Chip select
2 RS I Data/Command select
3 WR I Write strobe signal
4 RD I Read strobe signal
5 LCD_RST I LCD RESET signal, Low is active
6~21 DB0~ DB15 I/O Data bus(D0:LSB; D15:MSB)
22 GND Power Supply Power ground
23 BL_CTRL I Backlight control pin
24~25 OPEN No connection
26~27 GND Power supply Power ground
28 VDD5V Power supply Module Power input (5V Typ.) (*note1)
29 NC O No connection
30 CTP_SDA I TP Serial Data Input
31 CTP_INT I TP INT Interrupt Output
32 NC No connection
33 CTP_CS I TP Chip reset pin
34 CTP_SCL I TP Clock Input

LCD2 Interface Description for CTP

NO. Symbol I/O DESCRIPTION
1~2 GND Power supply Power ground
3 CS I Chip select
4 RS I Data/Command select
5 WR I Write strobe signal
6 RD I Read strobe signal
7 LCD_RST I LCD RESET signal, Low is active
8~23 DB0~ DB15 I/O Data bus(D0:LSB; D15:MSB)
24 GND Power supply Power ground
25 BL_CTRL I Backlight control pin
26~28 NC No connection
29~30 VDD5V Power supply Module Power input (5V Typ.)
31 NC O No connection
32 CTP_SDA I TP Serial Data Input
33 CTP_INT I TP INT Interrupt Output
34 NC No connection
35 CTP_RST I TP Chip Select Input
36 CTP_CLK I TP Clock Input
37 NC I No connection
38 NC I No connection
39~40 GND Power ground

LCD1 / LCD2 Interface Description for RTP

Surenoo SMC0700B-800480 Series MCU Interface TFT 5

INPUT TIMING

8080 Parallel Mode Interface Timing

Surenoo SMC0700B-800480 Series MCU Interface TFT 6

Symbol Parameter   Rating Unit Note
Min. Max.
TCYC8 Cycle Time 50 ns tc is one system clock period:

tc = 1/SYS_CLK

TCC8 Strobe Pulse Width 20 ns
TAS8 Address Setup Time 0 ns
TAH8 Address Hold Time 10 ns
TDS8 Data Setup Time 20 ns
TDH8 Data Hold Time 10 ns
TACC8 Data Output Access Time 0 20 ns
TOH8 Data Output Hold Time 0 20 ns

Register Write:

  1. Address Write: Write the Register’s Address. For example, 00h i.e. REG[00h], 01h i.e. REG[01h], 02h i.e. REG[02h] ……
  2. Data Write: Write Data to the Register

Register Read:

  1. Address Write: Write the Register’s Address
  2. Data Write: Read Data from the Register
    Displays Memory (Display RAM) is where the TFT screen image data is stored,. Host through interface and write data into Display RAM. The procedure of access Display RAM is as following:

Display RAM Write:

  1. Set the Active Window Registers before writing any image data.
  2. Perform an register write to Graphic R/W Position Register 0, REG[5Fh]).
  3. Repeat step 2 until setup all the Active Window & Graphic R/W Position Coordinates.
  4. Perform an address write to point to Memory Data Port Register (REG[04h])
  5. Perform data writes to fill the window. Each write to the Memory Data Port will auto-increment the internal memory address.

RELIABILITY TEST CONDITIONS

No. Test Item Test Condition
1 High Temperature Storage 80℃/120 hours
2 Low Temperature Storage -30℃/120 hours
3 High Temperature Operating 70℃/120 hours
4 Low Temperature Operating -20℃/120 hours
5 Temperature Cycle Storage -20℃(30min.)~25(5min.)~70℃(30min.)×10cycles
AInspection after test:

Inspection after 2~4 hours storage at room temperature, the sample shall be free from defects:

Ø  Air bubble in the LCD;

Ø  Sealleak;

Ø  Non-display;

Ø  Missing segments;

Ø  Glass crack;

Ø  Current is twice higher than initial value.

BRemark:

Ø  The test samples should be applied to only one test item.

Ø  Sample size for each test item is 5~10pcs. 

Ø  Failure Judgment Criterion: Basic Specification, Electrical Characteristic, Mechanical Characteristic, Optical Characteristic.

INSPECTION CRITERION

This specification is made to be used as the standard of acceptance/rejection criteria for TFT-LCD/IPS TFT-LCD module product, and this specification is applicable only in the case that the size of module equal to or exceed than 3.5 inch.

Sample plan
Sampling plan according to GB/T2828.1-2003/ISO 2859-1:1999 and ANSI/ASQC
Z1.4-1993,normal level 2 and based on:
Major defect: AQL 0.65
Minor defect: AQL 1.5

Inspection condition
Viewing distance for cosmetic inspection is about 30cm with bare eyes, and under an environment of 20~40W light intensity, all directions for inspecting the sample should be within 45°against perpendicular line. (Normal temperature 20~25℃and normal humidity 60±15%RH )

Definition of Inspection Item.
Definition of inspection zone in LCD.

Surenoo SMC0700B-800480 Series MCU Interface TFT 7

Zone A: character/Digit area
Zone B: viewing area except Zone A (Zone A + Zone B=minimum Viewing area)
Zone C: Outside viewing area (invisible area after assembly in customer’s product)

Fig.1 Inspection zones in an LCD
Note: As a general rule, visual defects in Zone C are permissible, when it is no trouble for quality and assembly of customer’s product.

Definition of some visual defect

Bright dot Because of losing all or part function, bad pixel dots appear bright and the size is more than 50% of one dot in which LCD panel is displaying under black pattern.
Dark dot Dots appear dark and unchanged in size in which LCD panel is displaying under pure red, green, blue picture, or pure whiter picture.

Major Defect 

Item

No.

Items to be

inspected

Inspection standard Classification of defects
1 Functional defects 1)  No display

2)  Display abnormally

3)  Missing vertical, horizontal segment

4)  Short circuit

5)  Excess power consumption

6)Backlight no lighting,   flickering   and abnormal lighting

 

 

 

 

 

major

2 Missing Missing component
3 Outline dimension Overall outline dimension beyond the drawing is not allowed

Minor Defect 

Surenoo SMC0700B-800480 Series MCU Interface TFT 8

Surenoo SMC0700B-800480 Series MCU Interface TFT 14

Surenoo SMC0700B-800480 Series MCU Interface TFT 9

Module Cosmetic Criteria

Item

No.

Items to be

inspected

Inspection Standard Classification

of defects

1 Difference in Spec. Not allowable Major
2 Pattern peeling No substrate pattern peeling and floating Major
3 Soldering defects No soldering missing Major
No soldering bridge Major
No cold soldering Minor
4 Resist flaw on PCB Visible copper foil (Φ0.5 mm or more) on substrate pattern is not allowed Minor
5 FPC gold finger No dirt, breaking, oxidation lead to black Major
6 Backlight plastic

frame

No deformation, crack, breaking, backlight positioning column breaking, obvious nick. Minor
7 Marking printing

effect

No dark marking, incomplete, deformation lead to unable to judge Minor
8 Accretion of metallic

Foreign matter

No accretion of metallic foreign matter (Not exceed Φ0.2mm) Minor
9 Stain No stain to spoil cosmetic badly Minor
10 Plate discoloring No plate fading, rusting and discoloring Minor
11 1. Lead parts a. Soldering side of PCB Solder to form a ‘Filet’ all around the lead. Solder should not hide the lead form perfectly. Minor
b. Components side(In case of ‘Through Hole PCB’) Solder to reach the Components side of PCB.  

Minor

2. Flat packages Either ‘Toe’(A) or ‘Seal’(B)of the lead to be covered by “Filet”. Lead form to be assume over Solder.

Surenoo SMC0700B-800480 Series MCU Interface TFT 10

 

 

Minor

 

 

3. Chips

(3/2) H ≥h ≥(1/2) H

Surenoo SMC0700B-800480 Series MCU Interface TFT 11

 

Minor

4. Solder ball/Solder splash a. The spacing between solder ball and the conductor or solder pad h ≥0.13 mm. The diameter of solder ball d≤0.15 mm. Minor
b. The quantity of solder balls or solder splashes isn’t beyond 5 in 600 mm2. Minor
c. Solder balls/Solder splashes do not violate minimum electrical clearance.  

Major

Documents / Resources

Surenoo SMC0700B-800480 Series MCU Interface TFT LCD Module [pdf] User Manual
SMC0700BA3-800480, SMC0700B-800480 Series, SMC0700B-800480 Series MCU Interface TFT LCD Module, MCU Interface TFT LCD Module, TFT LCD Module, LCD Module, Module

References

Leave a comment

Your email address will not be published. Required fields are marked *