msi S1102, D3051 CPU Single AMD Ryzen Processor
Specifications:
- CPU: Single AMD RyzenTM 7000/9000 Series and EPYCTM 4004/4005 Series Processor
- Memory: DDR5 ECC/non-ECC UDIMMs, supporting speeds up to 5600 MT/s (1DPC) and 3600 MT/s (2DPC)
- Connectors: Various connectors including JPWR1, JPWR2, JSDOMPWR1, SATA1~4, SATA3_1, M2_1~2, PCIE_1, PCIE_2, FAN1~8, PUMP1, JFP1, JTPM1, JGPIO1, JPMBUS1, etc.
DIMESSION
LAN ports in the red dashed area vary with SKUs; please refer to the specifications for more details.
CPU
Single AMD Ryzen™ 7000/9000 Series and EPYC™ 4004/4005 Series Processor
Front Panel Header
Important
The server board is equipped with one or two types of NIC chips for different SKUs. The first type, NIC#1, is controlled by Intel® I210-AT and manages 1GbE RJ45 ports (JLANCONN1). The second type, NIC#2, is controlled by Intel® X710-AT2 and manages 10GbE RJ45 ports (JLAN1~2).
CPU and Cooler Installation
Important
- For proper operation of the liquid cooler, replace non-spring screws with spring screws.
- Following the S1102-01 heatsink installation, remove the polystyrene cube on the backside of the air duct before proceeding with air duct installation.
Connectors, Jumpers and LED Indicators
| Name | Description |
| JPWR1 | 8-pin 12V power connector |
| JPWR2 | 24-pin main power connector |
| JSDOMPWR1 | 2-pin SATA DOM power connector |
| SATA1~4 | SATA 3.0 6Gb/s ports |
| SATA3_1 | SATA 2.0 3Gb/s ports |
| M2_1~2 | M.2 slots (M Key, PCIe 4.0, 22110/ 2280) |
| PCIE_1 | PCIe 5.0 x 16 slot (Gen 5 x 16 signal from CPU) |
| PCIE_2 | PCIe 4.0 x 8 slot (Gen 4 x 4 signal from CPU) |
| Name | Description |
| FAN1~8, PUMP1 | Fan connectors |
| JFP1 | Front panel header |
| JTPM1 | SPI TPM header |
| JGPIO1 | GPIO header |
| JPMBUS1 | PM Bus header |
| JCHASSIS1 | Chassis intrusion header |
| JIPMB1 | IPMB header |
| FP_I2C_1, RBP_I2C_1~2 | I2C headers |
| JCOM1 | COM port header |
| JUSB1 | USB 3.2 Gen 1 header |
| JUSB2 | USB 3.2 Gen 1 Type-A port |
| MLAN_USB1 | GbE RJ45 port (for mgmt.) (upper, on rear side) |
| USB 3.2 Gen 1 Type-A ports (lower, on rear side) | |
| REAR_USB1 | USB 3.2 Gen 1 Type-A ports (on rear side) |
| JLAN1~2* | 10 GbE RJ45 ports (on rear side) |
| JLANCONN1 (U, L)* | GbE RJ45 ports (on rear side) |
| COM1 | COM port (on rear side) |
| JVGA1 | VGA port (on rear side) |
| JSEL_M1 | M2_1 / PCIE_2 select jumper (default set to pin 1-2, M2_1 enabled) |
| JSEL_BMC1 | BMC select jumper (default pin 1-2, using CPU) |
| PWRTEST1 | Power test jumper (default pin 1-2, normal) |
| JRTC_CLR1 | CMOS clear jumper (default pin 1-2 normal) |
| BMC_LED1 | BMC Heartbeat LED |
| LED_H1, LED_L1 | Port 80 Debug LEDs |
*LAN ports vary with SKUs, please refer to the specifications for more details.
Memory
The server board offers compatibility with DDR5 ECC/ non-ECC UDIMMs, supporting memory speeds up to 5600 MT/s (1DPC) and 3600 MT/s (2DPC).
Recommended Memory Population
Important
- Only support UDIMM.
- Paired memory installation for Max performance.
- There should be at least 1 DDR5 DIMM populated.
- If only 1 DIMM is populated in a channel, then populate it in the DIMMA2 slot.
- Populate the same DIMM type in each channel, specifically: 1. Use the same DIMM size; 2. Use the same number of ranks per DIMM.
- We don’t suggest other memory installation.
FAQ
- Q: What type of memory does the server board support?
A: The server board supports DDR5 ECC/non-ECC UDIMMs with memory speeds up to 5600 MT/s (1DPC) and 3600 MT/s (2DPC). - Q: How should I populate the memory slots for optimal performance?
A: Populate the memory slots according to the recommended memory population guidelines provided in the manual. Ensure paired memory installation for maximum performance and follow the guidelines for DIMM placement.
Documents / Resources
 |
msi S1102, D3051 CPU Single AMD Ryzen Processor [pdf] User Guide S1102-01, S336-S1102-D3051-v2.0-QG, S1102 D3051 CPU Single AMD Ryzen Processor, S1102 D3051, CPU Single AMD Ryzen Processor, Single AMD Ryzen Processor, AMD Ryzen Processor, Ryzen Processor, Processor |