User Guide for msi models including: S1102-01, S336-S1102-D3051-v2.0-QG, S1102 D3051 CPU Single AMD Ryzen Processor, S1102 D3051, CPU Single AMD Ryzen Processor, Single AMD Ryzen Processor, AMD Ryzen Processor, Ryzen Processor, Processor
⚠Important. The server board is equipped with one or two types of NIC chips for different SKUs. The first type, NIC#1, is controlled by Intel I210-AT and ...
1 giorno fa — Following the S1102-01 heatsink installation, remove the polystyrene cube on the backside of the air duct before proceeding with air duct installation.
MSI D3051 Server Motherboard: uATX Form Factor with Support for AMD Ryzen 7000 Series Processor
G52-S3362X5 CPU and Cooler Installation S1102 / D3051 QUICK START GUIDE LAN ports in the red dashed area vary with SKUs; please refer to the specifications for more details. BZ1 GbE RJ45 Port (for mgmt.) GbE RJ45 Port 10 GbE RJ45 Port COM Port UID LED Button USB 3.2 Gen 1 Type-A Port VGA Port 2 1 Air Cooling 1 3 4 92 8 Torque: 5.5-6.1 kgf·cm ID_BTN1 COM1 (U) JVGA1 (L) REAR_USB1 JPWR1 DIMMA1 JCOM1 MLAN_USB1 JLANCONN1(U) JLANCONN1(L) JLAN1 JLAN2 LED_H1 LED_L1 DIMMB2 DIMMA2 DIMMB1 Liquid Cooling 3 Torque: 5.5-6.1 kgf·cm 1 3 4 10 2 PCIE_4 JPMBUS1 PCIE_16 FAN8 PUMP1 BMC_LED1 M2_2 9 7 4 JPWR2 BMC Flash 6 JSEL_M1 JSEL_BMC1 M2_1 BMC_F1 JUSB1 JGPIO1 JCHASSIS JIPMB1 SATA1 JSDOMPWR1 SATA2 SATA3 SATA4 JFP1 SPI3 PWRTEST1 JRTC_CLR1 FAN1 FAN2 FAN3 FAN4 FAN5 FAN6 FAN7 RBP_I2C_2 FP_I2C_1 RBP_I2C_1 BIOS Flash BAT1 JUSB2 JTPM1 SATA3_1 CPU Single AMD RyzenTM 7000/9000 Series and EPYCTM 4004/4005 Series Processor Front Panel Header 2 24 JFP1 1 23 1 PWR_LED+ 3 No pin 5 PWR_LED- 7 HDD_ACT_LED+ 9 HDD_ACT_LED- 11 PWR_BTN Important 2 FP_PWR 13 PWR_BTN_GND 14 NIC#1_ACT_LED- 4 SYS_ID_LED+ 15 RST_BTN 16 SMB_SDA 6 SYS_ID_LED- 17 RST_BTN_GND 18 SMB_SCL 8 SYS_FAULT_LED1- 19 SYS_ID_BTN 20 CHASSIS_INTRUSION 10 SYS_FAULT_LED2- 21 WIRE_TEMP_SENSOR 22 NIC#2_ACT_LED+ 12 NIC#1_ACT_LED+ 23 NMI_BTN 24 NIC#2_ACT_LED- The server board is equipped with one or two types of NIC chips for different SKUs. The first type, NIC#1, is controlled by Intel® I210-AT and manages 1GbE RJ45 ports (JLANCONN1). The second type, NIC#2, is controlled by Intel® X710-AT2 and manages 10GbE RJ45 ports (JLAN1~2). 5 8 Important For proper operation of the liquid cooler, replace non-spring screws with spring screws. Following the S1102-01 heatsink installation, remove the polystyrene cube on the backside of the air duct before proceeding with air duct installation. Connectors, Jumpers and LED Indicators Name JPWR1 JPWR2 JSDOMPWR1 SATA1~4 SATA3_1 M2_1~2 PCIE_1 PCIE_2 Description 8-pin 12V power connector 24-pin main power connector 2-pin SATA DOM power connector SATA 3.0 6Gb/s ports SATA 2.0 3Gb/s ports M.2 slots (M Key, PCIe 4.0, 22110/ 2280) PCIe 5.0 x 16 slot (Gen 5 x 16 signal from CPU) PCIe 4.0 x 8 slot (Gen 4 x 4 signal from CPU) Name FAN1~8, PUMP1 JFP1 JTPM1 JGPIO1 JPMBUS1 JCHASSIS1 JIPMB1 FP_I2C_1, RBP_I2C_1~2 JCOM1 JUSB1 JUSB2 MLAN_USB1 REAR_USB1 JLAN1~2* JLANCONN1 (U, L)* COM1 JVGA1 JSEL_M1 JSEL_BMC1 PWRTEST1 JRTC_CLR1 BMC_LED1 LED_H1, LED_L1 Description Fan connectors Front panel header SPI TPM header GPIO header PMBus header Chassis intrusion header IPMB header I2C headers COM port header USB 3.2 Gen 1 header USB 3.2 Gen 1 Type-A port GbE RJ45 port (for mgmt.) (upper, on rear side) USB 3.2 Gen 1 Type-A ports (lower, on rear side) USB 3.2 Gen 1 Type-A ports (on rear side) 10 GbE RJ45 ports (on rear side) GbE RJ45 ports (on rear side) COM port (on rear side) VGA port (on rear side) M2_1 / PCIE_2 select jumper (default set to pin 1-2, M2_1 enabled) BMC select jumper (default pin 1-2, using CPU) Power test jumper (default pin 1-2, normal) CMOS clear jumper (default pin 1-2 normal) BMC Heartbeat LED Port 80 Debug LEDs *LAN ports vary with SKUs, please refer to the specifications for more details. Memory The server board offers compatibility with DDR5 ECC/ non-ECC UDIMMs, supporting memory speeds up to 5600 MT/s (1DPC) and 3600 MT/s (2DPC). DIMMB2 Channel B DIMMB1 DIMMA2 Channel A DIMMA1 Recommended Memory Population Quantity of DIMMs 1 2 3 4 Channel B DIMMB2 DIMMB1 V V V V V V V V DIMMA2 V V Channel A DIMMA1 V V V V V V V "V"indicates a populated DIMM slot. Important Only support UDIMM. Paired memory installation for Max performance. There should be at least 1 DDR5 DIMM populated. If only 1 DIMM is populated in a channel, then populate it in the DIMMA2 slot. Populate the same DIMM type in each channel, specifically: 1. Use the same DIMM size; 2. Use the same number of ranks per DIMM. We don't suggest other memory installation.Adobe PDF Library 17.0 Adobe InDesign 20.1 (Windows)