Danfoss TP5001B-TP5001RF Programmable Room Thermostat User Guide

Symbols	Function description
Mon – Sun	Current set day
	Current on/off period
	Current set time / parameter number in setup
	Room temperature
	Temperature indication
	Set temperature
	Heating active
	Frost protect active
	Schedule mode
	Away mode
	RF Status (TP5001RF only)
	Battery low indicator (TP5001B & TP5001RF only)

2 Buttons

Symbols	Function description
	Power on/off
	Timer and program operation
M	Mode change / option setting
< >	Temperature / option setting selectors

3 Power ON/OFF

Turn the thermostat ON or OFF (standby) by pressing .

4 Setting the Temperature

Press < or > at any time to change the desired temperature value. SET is shown in the display.
When releasing < or >, the display returns to showing the actual temperature.

The adjustment step is 0.5 °C.

5 Select Away Mode

Press M to enter Away mode and will be displayed.

Away mode temperature can be set in parameter settings, P07.
Press M again to exit Away mode.

6 Set Date & Time

Press ; Year digit Flashes. Press < or > buttons to adjust year.
Press again; Month digit flashes. Press < or > buttons to adjust month.

Press again; Day digit flashes. Press < or > buttons to adjust day of the month.
Press again; Hour digit flashes. Press < or > buttons to adjust hour.

Press again; Minute digit flashes. Press < or > buttons to adjust minute.
Press to exit, automatic exit after 20 seconds, any changes are retained.

7 Frost Protection Temperature

You can switch the thermostat OFF (Standby) by alternately pressing . In OFF (Standby) mode, the thermostat is set to a Frost Protection temperature setting and will switch On only if the measured temperature falls below this temperature (5 °C by default).
The frost protect icon and current temperature will be displayed.

8 Advanced Programmable Timer

The Advanced Programmable Timer mode enables the setting of a timer-controlled program for automatic comfort temperature, and an energy-saving lower setback temperature if standard room comfort temperature is not required.

Example below for 5/2 day setup, 4 Temperature settings.

The function consists of 2 programs:
P1 with 4 events in 5 days (Mon. Tue. Wed. Thu. Fri.) P2 with 4 events in 2 days (Sat. Sun.).

P1: Press

for 3 secs to display Mo. Tu. We. Th. Fr.

P1, Event 1:

Use < or > to select the start hour.
Press to accept the setting.
Use < or > to set the minute.
Press to accept the setting.
Use < or > to select the temperature.
Press to accept the setting.

P1, Event 2-4:
Repeat the Event 1 procedure for programming Event 2-4.

P2: Sa. Su. are now shown in the display.

P2, Event 1:

Use < or > to select the start hour.
Press to accept the setting.
Use < or > to set the minute.
Press to accept the setting.
Use < or > to select the temperature.
Press to accept the setting.

P2, Event 2-4:
Repeat the Event 1 procedure for programming Event 2-4.

If schedule working mode is set to 24hr, only P1 program will be available, see parameter P01. Mo. to Su. will be set together with the same times and temperatures.

The thermostat will continue the 4-event program based on the present time and day.

To set and change the room temperature temporarily:

Press < or > at any time to change the desired temperature value. SET is shown in the display.
When releasing the < or >, the display returns to showing the actual temperature. This temperature change is only temporary and will be maintained only until the next programmed setting!

A default program provides timer control if the customer does not create own programs:

Days	Event 1		Event 2		Event 3		Event 4
Days	Start time	Temp.	Start time	Temp.	Start time	Temp.	Start time	Temp.
Mo. – Fr.	6:30	20° C	8:30	15° C	16:30	20° C	22:30	15° C
Sa. – Su.	7:30	20° C	9:30	15° C	16:30	20° C	22:30	15° C

* 24hr mode default program same as Mo. – Fr. above.

9 Set Control Parameters

Press M button for 6 seconds to enter the parameter setting mode. Press M for parameter selection and set the parameter range via < or >. Complete all adjustments.
To exit press , which is available for this purpose (automatic exit after 20 seconds with no operation).

The digits indicate the set value as follows:

No.	Parameter settings	Settings range	Default
P01	Working mode	01: Manual 02: Schedule timer 5/2 day 03: Schedule timer 24hr	02
P02	Heat control mode	01: On/off load compensation 02: On/off standard	01
P03	Heat control start-up mode	01: Normal start control 02: Delayed start control 03: Optimised start control	01
P04	Temperature limit high	Between low (P05) and 35° C	35° C
P05	Temperature limit low	Between 5° C and high (P04)	5° C
P06	Frost protect temperature	Between 5° C and 15° C	5° C
P07	Away mode temperature	Between low (P05) and high (P04)	18° C
P08	Timer display	01: 24hr 02: 12hr	24hr
P09	Service due setup	Installer setting only
P10	RF Pairing (TP5001RF only)	00: RF pairing mode off 01: RF pairing mode on	00
P11	Auto daylight saving	01: On 02: Off	01

10 Error Messages

E1	Sensor failure
EE	EEPROM failure
Lo	Measured temperature below 0 °C
Hi	Measured temperature above 50 °C
E3	RF Pairing failed
E4	RF Signal lost
E6	Real Time Clock (RTC) failure

Danfoss Limited
Climate Solutions • danfoss.uk • 0330 8086 888 • customerservice.uk@danfoss.com
Danfoss Ltd., Building 4, Uxbridge Business Park, Sanderson Road, UB8 1 DH, Uxbridge, Buckinghamshire, UK

Any information, including, but not limited to information on selection of product, its application or use, product design, weight, dimensions, capacity or any other technical data in product manuals, catalogues descriptions, advertisements, etc. and whether made available in writing, orally, electronically, online or via download, shall be considered informative, and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility for possible errors in catalogues, brochures, videos and other material.
Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without changes to form, fit or function of the product.
All trademarks in this material are property of Danfoss A/S or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss A/S. All rights reserved.

Danfoss Climate Solutions BC306936081288EN-010201 03/2023

Documents / Resources

Danfoss TP5001B-TP5001RF Programmable Room Thermostat [pdf] User Guide
TP5001B, TP5001RF, TP5001B-TP5001RF Programmable Room Thermostat, TP5001B-TP5001RF, Programmable Room Thermostat, Room Thermostat, Thermostat

References

User Manual

User Guide

TP5001

Programmable Room Thermostat

1 LCD Overview