mylumens LC300 CaptureVision системасы 4 каналдуу жазгыч жана агымдык медиа процессордун ээлеринин колдонмосу

Lumens VC-TR40 PTZ камераларын CaptureVision LC300/LC300S менен жупташтырып, Intelligent Director функциясын иштетиңиз. Ар бир VC-TR40 PTZ камерасы Lumens'тен жүктөп ала турган VC-TR40 AT микропрограммасын иштетиши керек. webсайт. AT микропрограммасы стандарттык версиядан байкоо функциялары боюнча гана айырмаланат; башка бардык функциялар бирдей.

What is the difference between VC-TR40 & VC-TR40 AT?

VC-TR40 and VC-TR40 AT firmware have different tracking functions.
a. VC-TR40 tracks or frames a target in the tracking zone. Available modes:
• Everywhere Tracking, Stage Tracking, Partition Tracking, Auto Framing, Partition Framing
b. VC-TR40 AT offers two modes:
• Presenter Mode: The camera tracks the target within the tracking zone. Tracking behavior is the same as VC-TR40 Everywhere Tracking.
• Audience Mode: The camera starts tracking when it detects a target standing up and stops when the target sits down.

Installed scenario for VC-TR40 AT

1. Scenario for 3x VC-TR40 AT cameras (single presenter camera and two audience cameras) – suitable for a conference room.
   ⚫ Install the presenter camera at the back of a room, facing the podium or presentation area.
   ⚫ Audience Cameras: Install at the front of a room, facing the audience.
   
2. Scenario for 2x VC-TR40 AT cameras in a smaller classroom or meeting space.
   ⚫ Install camera 1 at the back of a room to capture the presenter.
   ⚫ Install camera 2 at the front of a room to capture the audience.
   
3. Scenario for 2x VC-TR40 AT cameras covering a large stage аймагы.
   ⚫ Install both cameras at the back of a room to track the presenter.
   
4. Scenario for 1x VC-TR40 AT* in a small stage аймагы.
   ⚫ Install the camera at the back of a room to capture the presenter.
   

How to update VC-TR40 to VC-TR40 AT?

1. Download VC-TR40 AT firmware from www.MyLumens.com.
2. Connect the camera with a network cable and enter VC-TR40’s IP address in your web браузер
3. Go to [Maintenance] -> [Update], select the new firmware file жана Жаңыртуу дегенди басыңыз.
4. Do not power off the camera. After 5-8 minutes the process will finish.
5. Clear cache and cookies. Enter the camera’s IP address on the browser and go to [Maintenance] -> [Update] to conduct a factory reset.
6. If the user wants to revert to the original VC-TR40 firmware, download the latest VC-TR40 firmware from www.MyLumens.com. Now repeat steps 3.1-3.5. The camera will return from VC-TR40 AT to VC-TR40.

How to set up Intelligent Director on LC300/LC300S and VC-TR40 AT

Сизге CaptureVision LC300/LC300S жана жок дегенде бир VC-TR40 AT (максималдуу 3кө чейин) керек болот. Аларды бир LANга туташтырыңыз. Биз мурунку үч VC-TR40 AT бирдигин колдонобузample.

1. Go to Mode setting in the web interface. On the “Tracking” tab, set one VC-TR40 AT into “Presenter Mode”, and the other cameras to “Audience Mode”.
   
2. First, let’s configure the VC-TR40 AT Audience Mode camera. Go to the “Command” tab in the webбетинде, "Дайыма жөнөтүү" дегенди тандаңыз, Тура туруңуз, Көп объектилер жана Отуруңуз жана "Сактоо" баскычын басыңыз.
   
3. Continue to configure the VC-TR40 AT Audience Mode camera. Go to “Advanced “tab, and follow the same settings as in the screen grab below. Director IP is your LC300/LC300S’s IP; the Device port is 52382. Click “Save”.
   
4. Next, configure the VC-TR40 AT Presenter Mode camera. Go to the webpage. Under “Command “tab, in Send Times select > Always send; in Up / Down Stage > Тандоо; Типти аныктоодо > Көп объектти аныктоону тандаңыз; Жүрүм-турумду аныктоодо > Кадимки тандаңыз. Белгиленген белги пайда болот, Максат мисс, өйдө көтөрүлүү Stage, жана Down Stage, жана Сактоо чыкылдатыңыз.
   
5. Continue to configure the VC-TR40 AT Presenter Mode camera. Go to the “Advanced“ tab, and follow the same settings as shown below. The Director IP is your LC300/LC300S’s IP. The Device port is 52382. Click “Save”.
   
6. Go to [System] -> [Output] to edit name of each VC-TR40 AT (this will help later settings).
   
   Буйруктар өтмөгүндөгү орнотуулар боюнча кеңири түшүндүрмө алуу үчүн VC-TR40 колдонуучу колдонмосун караңыз.
7. Let’s configure the LC300/LC300S. Go to its web интерфейс "Булак" > "Тармак булагы менеджери". Тармак булактарына үч VC-TR40 AT бирдигин кошуңуз.
   
8. Go to the “Video Channel Manager” tab and click “Edit”. Put the VC-TR40 AT Presenter Mode camera into Channel 2, VC-TR40 AT Audience Mode camera 1 into Channel 3, VC- TR40 AT Student Mode camera 2 into Channel 4, and click “Apply”.
   
9. Go to the “Intelligent Director”
   ⚫ Select Scene Trigger Timing. You can choose Anytime, Recording only, Streaming only, Recording or Streaming.
   ⚫ Select Template. You can choose Presenter*1、Audience*2, Presenter*1、 Audience*1, Presenter*1, Presenter*2.
   ⚫ Set up each camera with a Trigger Event, camera priority, and corresponding Scene. Then click Apply and turn on Intelligent Director.
   Exampле:
   Audience1 sets Trigger Event is Stand up、Priority is 1
   Audience2 sets Trigger Event is Stand up、Priority is 2
   Presenter sets Trigger Event is Target Found、Priority is 3
   Target lost sets Priority is 4
   
   
   

Документтер / Ресурстар

mylumens LC300 CaptureVision системасы 4 канал жазгыч жана агымдык медиа процессору менен [pdf] Колдонуучунун колдонмосу LC300, LC300S, VC-TR40 AT, LC300 CaptureVision системасы 4 каналдуу жазгыч жана агымдык медиа процессору менен, LC300, 4 каналдык жазгыч жана агымдык медиа процессору бар CaptureVision системасы, 4 каналдык жазгыч жана агымдык медиа процессору, стримдик медиа процессору, стримдик медиа процессору, Процессор

Шилтемелер

• User Manual