mylumens LC300 CaptureVision System Uban sa 4 Channel Recorder ug Streaming Media Processor's Owner's Manual
Ipares ang Lumens VC-TR40 PTZ nga mga kamera nga adunay CaptureVision LC300/LC300S aron mahimo ang function sa Intelligent Director. Ang matag VC-TR40 PTZ camera kinahanglan nga modagan sa VC-TR40 AT firmware nga mahimong ma-download gikan sa Lumens website. Ang AT firmware lahi lamang sa standard nga bersyon sa tracking functions; ang tanan nga uban nga mga gimbuhaton parehas.
What is the difference between VC-TR40 & VC-TR40 AT?
VC-TR40 and VC-TR40 AT firmware have different tracking functions.
a. VC-TR40 tracks or frames a target in the tracking zone. Available modes:
• Everywhere Tracking, Stage Pagsubay, Pagsubay sa Partisyon, Auto Framing, Framing sa Partition
b. VC-TR40 AT offers two modes:
• Presenter Mode: The camera tracks the target within the tracking zone. Tracking behavior is the same as VC-TR40 Everywhere Tracking.
• Audience Mode: The camera starts tracking when it detects a target standing up and stops when the target sits down.
Installed scenario for VC-TR40 AT
- Scenario for 3x VC-TR40 AT cameras (single presenter camera and two audience cameras) – suitable for a conference room.
⚫ Install the presenter camera at the back of a room, facing the podium or presentation area.
⚫ Audience Cameras: Install at the front of a room, facing the audience.
- Scenario for 2x VC-TR40 AT cameras in a smaller classroom or meeting space.
⚫ Install camera 1 at the back of a room to capture the presenter.
⚫ Install camera 2 at the front of a room to capture the audience.
- Scenario for 2x VC-TR40 AT cameras covering a large stage lugar.
⚫ Install both cameras at the back of a room to track the presenter.
- Scenario for 1x VC-TR40 AT* in a small stage lugar.
⚫ Install the camera at the back of a room to capture the presenter.
How to update VC-TR40 to VC-TR40 AT?
- Download VC-TR40 AT firmware from www.MyLumens.com.
- Connect the camera with a network cable and enter VC-TR40’s IP address in your web browser
- Go to [Maintenance] -> [Update], select the new firmware file ug i-klik Upgrade.
- Do not power off the camera. After 5-8 minutes the process will finish.
- Clear cache and cookies. Enter the camera’s IP address on the browser and go to [Maintenance] -> [Update] to conduct a factory reset.
- If the user wants to revert to the original VC-TR40 firmware, download the latest VC-TR40 firmware from www.MyLumens.com. Now repeat steps 3.1-3.5. The camera will return from VC-TR40 AT to VC-TR40.
How to set up Intelligent Director on LC300/LC300S and VC-TR40 AT
Kinahanglan nimo ang CaptureVision LC300/LC300S ug labing menos usa ka VC-TR40 AT (hangtod sa labing taas nga 3). Ikonektar sila sa parehas nga LAN. Atong gamiton ang tulo ka VC-TR40 AT units isip example.
- Go to Mode setting in the web interface. On the “Tracking” tab, set one VC-TR40 AT into “Presenter Mode”, and the other cameras to “Audience Mode”.
- First, let’s configure the VC-TR40 AT Audience Mode camera. Go to the “Command” tab in the webpage, pilia ang “Always send”, tsek ang Stand up, Multi-Obj., ug Lingkod, ug i-klik ang “Save”.
- Continue to configure the VC-TR40 AT Audience Mode camera. Go to “Advanced “tab, and follow the same settings as in the screen grab below. Director IP is your LC300/LC300S’s IP; the Device port is 52382. Click “Save”.
- Next, configure the VC-TR40 AT Presenter Mode camera. Go to the webpage. Under “Command “tab, in Send Times select > Always send; in Up / Down Stage Pagpili > Detect; sa Detect Type pilia > Multi-Obj Detect; sa Behavior Detect pilia > Normal. Markahan ang Target Pagpakita, Target nga Miss, Tuktok Stage, ug Go Down Stage, ug i-klik ang Save.
- Continue to configure the VC-TR40 AT Presenter Mode camera. Go to the “Advanced“ tab, and follow the same settings as shown below. The Director IP is your LC300/LC300S’s IP. The Device port is 52382. Click “Save”.
- Go to [System] -> [Output] to edit name of each VC-TR40 AT (this will help later settings).
Para sa detalyadong mga pagpasabot sa mga setting sa Commands tab, palihog tan-awa ang VC-TR40 user manual. - Let’s configure the LC300/LC300S. Go to its web interface "Source" > "Network Source Manager". Idugang ang tulo ka VC-TR40 AT unit sa mga tinubdan sa network.
- Go to the “Video Channel Manager” tab and click “Edit”. Put the VC-TR40 AT Presenter Mode camera into Channel 2, VC-TR40 AT Audience Mode camera 1 into Channel 3, VC- TR40 AT Student Mode camera 2 into Channel 4, and click “Apply”.
- Go to the “Intelligent Director”
⚫ Select Scene Trigger Timing. You can choose Anytime, Recording only, Streaming only, Recording or Streaming.
⚫ Select Template. You can choose Presenter*1、Audience*2, Presenter*1、 Audience*1, Presenter*1, Presenter*2.
⚫ Set up each camera with a Trigger Event, camera priority, and corresponding Scene. Then click Apply and turn on Intelligent Director.
Example:
Audience1 sets Trigger Event is Stand up、Priority is 1
Audience2 sets Trigger Event is Stand up、Priority is 2
Presenter sets Trigger Event is Target Found、Priority is 3
Target lost sets Priority is 4
Mga Dokumento / Mga Kapanguhaan
![]() |
mylumens LC300 CaptureVision System Uban ang 4 Channel Recorder ug Streaming Media Processor [pdf] Manwal sa Tag-iya LC300, LC300S, VC-TR40 AT, LC300 CaptureVision System Uban sa 4 Channel Recorder ug Streaming Media Processor, LC300, CaptureVision System Uban sa 4 Channel Recorder ug Streaming Media Processor, 4 Channel Recorder ug Streaming Media Processor, Streaming Media Processor, Streaming Media Processor, Processor |