4181502502 កាន់ដៃម៉ូនីទ័រ
“
ព័ត៌មានអំពីផលិតផល
លក្ខណៈបច្ចេកទេស
- Art. No: 4181502502, 4181502509, 4181502501
- Model: Hold Monitor Arm25
- Parts Included: A, B, C, D, E, F, G, H, I, K, L, M, N
- Screw Sizes: M6x12, M4x10
- Allen Key Sizes: 2mm, 4mm
ការណែនាំអំពីការប្រើប្រាស់ផលិតផល
Step 1: Adhere Pad to Clamp
Adhere pad (B) to the bottom side of the clamp (C). Adjust clamp
height with Allen Key (N) if needed. Fasten clamp ទៅតុ
ដោយប្រើចំណុចទាញ។
Step 2: Mount the Pole
Mount the pole (D) on the clamp using screws (E) and Allen key
(M). Complete assembly with plastic covers (F) & (G).
Step 3: Attach Monitor Arm
Attach the monitor arm (A) to the monitor using all four screws
(ហ)។
Step 4: Insert Arm onto Pole
Insert the arm with the fixed monitor onto the pole. Adjust to
desired height using the plastic handle.
Step 5: Lock Arm Position
Optional: Use Allen key (M) to tighten remaining joints to lock
the position of the arms.
ជំហានទី 6: ការគ្រប់គ្រងខ្សែ
Finish installation by directing the cables from the monitor
through the cable guides on arms and attaching cable clips (I) on
the pole. Use cable tie (K) to collect cables.
Optional Step: Lock Arm Position
To lock the position of the first arm, use Allen key (L) until
the screw grips the pole (D).
សំណួរដែលសួរញឹកញាប់ (FAQ)
Q: What should I do if I encounter incomprehensible steps
កំឡុងពេលដំឡើង?
A: If you encounter incomprehensible steps, please contact us
សម្រាប់ជំនួយ និងការបំភ្លឺ។
“`
FORMINGFUNCTION.SE
សៀវភៅណែនាំអ្នកប្រើប្រាស់
ART។ ទេ
១២៣ ៤
Hold Monitor Arm25
គ្រឿងបន្លាស់ និងឧបករណ៍
1
A
x1 PCE
B
×1 PCE
C
x1 PCE
D
×1 PCE
E
×4 PCS
M6x12
F
×1 PCE
G
×1 PCE
H
×4 PCS
I
×2 PCS
M4x10
K
×1 PCE
L
×1 PCE
2 ម។
M
×1 PCE
4 ម។
N
×1 PCE
5 ម។
In order to achieve a correct mounting of Hold Monitor Arm, you are advised to read and follow the instructions step by step. If there are incomprehensible steps, please let us know and we will get back to you.
· The products loading capacities are based on monitors’ center of gravity less than 3 cm from the end of the VESA interface.
· Loading capacity could be reduced if the monitor size is greater than 26 inches or if the thickness exceeds 5.5 cm.
សៀវភៅណែនាំអ្នកប្រើប្រាស់
STEP 1 Adhere pad (B) to the bottom side of the clamp (C). If needed: Adjust clamp height with Allen Key (N). Fasten clamp to the table using the handle.
1
ជំហានទី 2
Mount the pole (D) on clampដោយប្រើ
screws (E) and Allen key (M). Complete
2
assembly with plastic covers (F) & (G)
1
N OPTIONAL 12-86 mm
2
ជំហានទី 3
Attach the monitor arm (A) to the monitor using all four screws (H)
HOLD MONITOR ARM 25
ជំហានទី 4
Use Allen key (M) to loosen the left screw completely. Then, tighten the right screw to max torque (10±1 Nm). Adjust the angle of the monitor and secure its position by re-tightening the screw to max torque (10±1 Nm). The joint should now be completely rigid.
ជំហានទី 5
Insert the arm with the fixed monitor onto the pole. Adjust to desired height using the plastic handle.
M 2 10 Nm
1
M
3 10 Nm
១៦.៧ ម
Optional: Using Allen key (M), tighten the remaining joints to lock the position of the arms.
STEP 6 Finish installation by directing the cables from the monitor through the cable guides on arms and and by attaching the cable clips (I) on the pole.
Use the cable tie (K) to collect cables, where you deem fit.
៦៧ ៨
L 2 Optional: To lock the position of the first arm, use Allen key (L) until the screw grips the pole (D).
2
ខ្ញុំ ៤៨
FORMINGFUNCTION.SE
ឯកសារ/ធនធាន
 |
FORMING and FUNCTION 4181502502 Hold Monitor Arm [pdf] សៀវភៅណែនាំ 4181502509, 4181502501, 4181502502 Hold Monitor Arm, 4181502502, Hold Monitor Arm, Monitor Arm, Arm |