4181502502 Hold Monitor Arm
“
Product Information
Specifications
- Art. No: 4181502502, 4181502509, 4181502501
- Model: Hold Monitor Arm25
- Parts Included: A, B, C, D, E, F, G, H, I, K, L, M, N
- Screw Sizes: M6x12, M4x10
- Allen Key Sizes: 2mm, 4mm
Product Usage Instructions
Step 1: Adhere Pad to Clamp
Adhere pad (B) to the bottom side of the clamp (C). Adjust clamp
height with Allen Key (N) if needed. Fasten clamp to the table
using the handle.
Step 2: Mount the Pole
Mount the pole (D) on the clamp using screws (E) and Allen key
(M). Complete assembly with plastic covers (F) & (G).
Step 3: Attach Monitor Arm
Attach the monitor arm (A) to the monitor using all four screws
(H).
Step 4: Insert Arm onto Pole
Insert the arm with the fixed monitor onto the pole. Adjust to
desired height using the plastic handle.
Step 5: Lock Arm Position
Optional: Use Allen key (M) to tighten remaining joints to lock
the position of the arms.
Step 6: Cable Management
Finish installation by directing the cables from the monitor
through the cable guides on arms and attaching cable clips (I) on
the pole. Use cable tie (K) to collect cables.
Optional Step: Lock Arm Position
To lock the position of the first arm, use Allen key (L) until
the screw grips the pole (D).
Frequently Asked Questions (FAQ)
Q: What should I do if I encounter incomprehensible steps
during installation?
A: If you encounter incomprehensible steps, please contact us
for assistance and clarification.
“`
FORMINGFUNCTION.SE
USER MANUAL
ART. NO
4181502502 4181502509 4181502501
Hold Monitor Arm25
PARTS AND TOOLS
1
A
x1 PCE
B
×1 PCE
C
x1 PCE
D
×1 PCE
E
×4 PCS
M6x12
F
×1 PCE
G
×1 PCE
H
×4 PCS
I
×2 PCS
M4x10
K
×1 PCE
L
×1 PCE
2mm
M
×1 PCE
4mm
N
×1 PCE
5mm
In order to achieve a correct mounting of Hold Monitor Arm, you are advised to read and follow the instructions step by step. If there are incomprehensible steps, please let us know and we will get back to you.
· The products loading capacities are based on monitors’ center of gravity less than 3 cm from the end of the VESA interface.
· Loading capacity could be reduced if the monitor size is greater than 26 inches or if the thickness exceeds 5.5 cm.
USER MANUAL
STEP 1 Adhere pad (B) to the bottom side of the clamp (C). If needed: Adjust clamp height with Allen Key (N). Fasten clamp to the table using the handle.
1
STEP 2
Mount the pole (D) on clamp, using the
screws (E) and Allen key (M). Complete
2
assembly with plastic covers (F) & (G)
1
N OPTIONAL 12-86 mm
2
STEP 3
Attach the monitor arm (A) to the monitor using all four screws (H)
HOLD MONITOR ARM 25
STEP 4
Use Allen key (M) to loosen the left screw completely. Then, tighten the right screw to max torque (10±1 Nm). Adjust the angle of the monitor and secure its position by re-tightening the screw to max torque (10±1 Nm). The joint should now be completely rigid.
STEP 5
Insert the arm with the fixed monitor onto the pole. Adjust to desired height using the plastic handle.
M 2 10 Nm
1
M
3 10 Nm
4 M
Optional: Using Allen key (M), tighten the remaining joints to lock the position of the arms.
STEP 6 Finish installation by directing the cables from the monitor through the cable guides on arms and and by attaching the cable clips (I) on the pole.
Use the cable tie (K) to collect cables, where you deem fit.
3 1
L 2 Optional: To lock the position of the first arm, use Allen key (L) until the screw grips the pole (D).
2
I 1
FORMINGFUNCTION.SE
Documents / Resources
 |
FORMING and FUNCTION 4181502502 Hold Monitor Arm [pdf] Instruction Manual 4181502509, 4181502501, 4181502502 Hold Monitor Arm, 4181502502, Hold Monitor Arm, Monitor Arm, Arm |