KS-POWER-OUT
Powered Output Module
Features
- Loop powered
- Single loop address programmed via TCH-B200
- 24 VDC output with adjustable current level
- 2 x Monitored inputs
- Compact design
- Colour coded flying leads for easy installation
- LPCB approved
Description
KS-POWER-OUT is an addressable Powered Output Module which allows ancillary equipment to be powered from the loop for example conventional beam detectors or flame detectors..
A Hochiki SPE protocol device it is compatible with Kentec’s range of Takt is and Syncro addressable control panels.
A Hochiki SPE protocol device it is compatible with Kentec’s range of Takt is and Syncro addressable control panels.
The module provides a 24 VDC output with an engineer configurable current level, current level can be set through the fire alarm control panel from 2-32 mA in 2 mA increments. This can be used to power a third party device.
Two monitored inputs are provided for monitoring of outputs from the third party device to enable status to be indicated on the control panel i.e. Fire and Fault relays.
KS-POWER-OUT requires a single loop address which is programmed using the TCH-B200 programmer.
The compact design of the KS-POWER-OUT enables it to be installed within third party equipment.
Specification
| Ordering Code and Description | KS-POWER-OUT Powered Output Module |
| Operating Voltage | 17 – 41 VDC |
| Quiescent Current | 200 µA (at 41 V) |
| Alarm Current | 2.3 – 32.3 mA |
| Test Signal Voltage | 14 to 30 VDC |
| Input Ratings | Open Circuit >1oo kΩ Normal State -10 kΩ (EOL resistor provided) Input Activation -470 Ω (EOL resistor provided) Short Circuit <50 Ω |
| Operating Temperature Range | -1o °C to + 50 °C |
| Storage Temperature Range | -30 °C to + 6o °C |
| Max Humidity | 95% RH – Non Condensing (at 40 °C) |
| Colour/Case Material | Ivory / ACS |
| Weight (g) | 30 |
| Dimensions (mm) | 65 L x 42 W x 19 D |
| Approvals | LPCB approved to EN54-18:2005 |
KS-POWER-OUT panel configuration settings*
The following table details the configuration options available on the Kentec Taktis and Syncro AS control panels:
The following table details the configuration options available on the Kentec Taktis and Syncro AS control panels:
| Configuration Options | Taktis | Syncro AS/XT+ |
| Configurable location text | √ | √ |
| Fault Reporting Delay | √ | √ |
| Map to zone | √ | √ |
| Output Options | Default ring mode (Fire), Evacuate Output, Alert Output, Pre Alarm Output, Technical Alarm Output Fault Output, Security Output | Default ring mode (Fire), Evacuate Output, Alert Output, Pre Alarm Output, Technical Alarm Output Fault Output, Security Output |
| Silence able | √ | √ |
| Invert output operation | √ | X |
| Configurable delay | √ | √ |
| Drop on Reset (If output normally on) | √ | √ |
| Current Limit | √ | √ |
| Configurable Operating Duration | √ | X |
| Single Shot Mode | √ | √ |
| Input Actions | Fire, Fault, Pre Alarm, Technical Alarm, Evacuate, Alert, Security, Silence, Reset, Transparent Disablement, Test Mode, Change sensitivity mode, Status, Acknowledge Alarm Extended Delay, Acknowledge Alarm Only, Override Delays |
Fire, Fault, Pre Alarm, Technical Alarm, Evacuate, Alert, Security, Silence, Reset, Transparent Disablement, Test Mode |
| Input Action Message | √ | √ |
| Bypass Output Delay | √ | √ |
| Input Delay | √ | √ |
| Latching or Non-Latching | √ | √ |
| Invert input | √ | X |
| Disablement as a Plant Control Output | √ | X |
* KS-POWER-OUT will be identified on Takt is and Syncro AS/XT+ control panels and on LE2 software as its Hochiki equivalent part number CHQ-POM.
Datasheet DS215 06/24 Rev.01
For further information visit www.kentec.co.uk
Kentec Electronics Ltd. reserves the right to alter the specification of its products from time to time without notice.
Although every effort has been made to ensure the accuracy of the information contained in this document it is not warranted or represented by Kentec Electronics Ltd. to be a complete and up-to-date description.
Documents / Resources
 |
Kentec KS-POWER-OUT System Wired Fire Detection [pdf] Owner's Manual KS-POWER-OUT, DS215-KS-POWER-OUT-Rev.01, KS-POWER-OUT System Wired Fire Detection, KS-POWER-OUT, System Wired Fire Detection, Wired Fire Detection, Fire Detection, Detection |