Lampu Sensor Lampu Manual / Lembar Data / Instruksi

BEGA 85 056 Garden and Pathway Luminaire kanthi PIR Motion and Light Sensor Instruction Manual

BenQ LW855UST, LH856UST Proyektor RS232 Spesifikasi Kontrol Komando Model: LW855UST/ LH856UST Metode Kontrol Proyektor: RS232 Kontrol Komando Pilihan Sambungan: RS232 port serial, LAN, HDBaseT Baud Rate: 115200 bps (standar, kasedhiya setelan Paritas Data) Durasi Bit Data 8 : Ora ana Stop Bit: 1 dicokot Flow Control: Ora ana Product Instruksi Dianggo RS232 Serial Port Sambungan Kanggo nyambungake liwat port serial RS232: Sambungake D-Sub 9 pin (lanang) ing proyektor kanggo PC utawa laptop nggunakake kabel komunikasi (crossover). Setel jeneng Port COM ing Manager Piranti lan pilih port COM sing cocog (contone, COM6). Setel setelan port Serial kalebu Baud rate, Data dawa, Parity check, Stop bit, lan kontrol aliran adhedhasar syarat sampeyan. RS232 liwat LAN Kanggo nyambungake liwat LAN: Sambungake port RJ45 ing proyektor menyang PC utawa laptop nggunakake kabel LAN. Priksa manawa proyektor lan komputer ana ing jaringan sing padha. Ing menu OSD, temokake alamat IP LAN Kabel proyektor lan ketik 8000 ing kolom TCP port #. RS232 liwat HDBaseT Kanggo nyambungake liwat HDBaseT: Sambungake piranti sing kompatibel karo HDBaseT menyang port RJ45 ing proyektor nggunakake kabel LAN. Setel jeneng Port COM ing Manager Piranti lan pilih port COM sing cocog. Setel setelan port Serial kalebu Baud rate, Data dawa, Parity check, Stop bit, lan kontrol aliran adhedhasar syarat sampeyan. Pitakonan sing Sering Ditakoni (FAQ) P: Apa fungsi sing kasedhiya kanggo kontrol RS232? A: Fungsi sing kasedhiya kalebu Power On, Power Off, Power Status, Source Selection, Audio Control, Mute On/Off, Volume +/-, lan liya-liyane. Deleng tabel printah ing manual kanggo dhaptar rinci fungsi. Pambuka Dokumen kasebut nerangake carane ngontrol proyektor BenQ liwat RS232 saka komputer. Tindakake tata cara kanggo ngrampungake sambungan lan setelan dhisik, banjur deleng tabel printah kanggo printah RS232. Fungsi lan printah sing kasedhiya beda-beda miturut model. Priksa spesifikasi lan manual pangguna proyektor sing dituku kanggo fungsi produk. Susunan kawat Rangkaian kawat P1 Warna P2 1 Ireng 1 2 Coklat 3 3 Abang 2 4 Oranye 4 5 Kuning 5 6 Ijo 6 7 Biru 7 8 Ungu 8 9 Abu-abu 9 Kasus Kawat Penguras RS232 Pin Penugasan Pin Keterangan Pin Keterangan 1 NC 2 RXD 3 TXD 4 NC 5 GND 6 NC 7 RTS 8 CTS 9 NC Sambungan lan setelan komunikasi Pilih salah siji sambungan lan nyetel kanthi bener sadurunge kontrol RS232. Port serial RS232 nganggo kabel silang Setelan Gambar ing layar ing dokumen iki mung kanggo referensi. Layar bisa beda-beda gumantung saka Sistem Operasi, port I/O sing digunakake kanggo sambungan, lan spesifikasi proyektor sing disambungake. Temtokake jeneng Port COM sing digunakake kanggo komunikasi RS232 ing Manager Piranti. Pilih Serial lan port COM sing cocog minangka port komunikasi. Ing ex diwenehi ikiample, COM6 dipilih. Rampung persiyapan port Serial. Baud rate 115200 bps (standar) Setelan sing bisa diganti ing User OSD (9600/14400/19200/38400/57600/115200) Dawa data 8 bit Parity check None Stop bit 1 bit Kontrol aliran Ora ana RS232 liwat Setelan LAN Temokake alamat IP LAN Kabel saka proyektor sing disambungake saka menu OSD lan priksa manawa proyektor lan komputer ana ing jaringan sing padha. Input 8000 ing lapangan TCP port #. RS232 liwat Setelan HDBaseT Nemtokake jeneng Port COM sing digunakake kanggo komunikasi RS232 ing Manager Piranti. Pilih Serial lan port COM sing cocog minangka port komunikasi. Ing ex diwenehi ikiample, COM6 dipilih. Rampung persiyapan port Serial. Baud rate 115200 bps (standar) Setelan sing bisa diganti ing User OSD (9600/14400/19200/38400/57600/115200) Dawa data 8 bit Periksa paritas None Stop bit 1 bit Kontrol aliran Ora ana Tabel perintah Fitur sing kasedhiya beda-beda miturut spesifikasi proyektor, sumber input , setelan, lsp. Printah bisa digunakake yen daya siyaga 0.5W utawa baud rate sing didhukung proyektor disetel. Huruf gedhe, huruf cilik, lan campuran saka rong jinis karakter ditampa kanggo prentah. Yen format printah iku ilegal, bakal echo format Illegal. Yen printah kanthi format sing bener ora valid kanggo model proyektor, bakal nyumerepi item sing ora didhukung. Yen prentah kanthi format sing bener ora bisa dieksekusi ing kahanan tartamtu, bakal mbaleni item Blok. Yen kontrol RS232 dileksanakake liwat LAN, printah bisa digunakake yen diwiwiti lan diakhiri nganggo . Kabeh printah lan prilaku podho rupo karo kontrol liwat port serial. Jinis Fungsi Operasi ASCII Dhukungan Daya Tulis Daya Aktif *pow=on# Ya Tulis Daya mati *pow=mati# Ya Waca Status Daya *pow=?# Ya Pilihan Sumber Tulis KOMPUTER/YPbPr *asem=RGB# Ya Tulis KOMPUTER 2/YPbPr2 *asem=RGB2# Ora Tulis KOMPUTER 3/YPbPr3 *asem=RGB3# Ora Tulis Komponen *asem=ypbr# Ora Tulis Komponen2 *asem=ypbr2# Ora Tulis DVI-A *asem=dviA# Ora Tulis DVI-D *asem= dvid# Ora Tulis HDMI(MHL) *asem=hdmi# Ya Tulis HDMI 2(MHL2) *asem=hdmi2# Ya Tulis Gabungan *asem=vid# Ora Tulis S-Video *asem=svid# Ora Tulis Jaringan *asem=jaringan # Ora Tulis Tampilan USB *asem=usbdisplay# Ora Tulis USB Reader *asem=usbreader# Ora Tulis HDBaseT *asem=hdbaset# Ora Tulis DisplayPort *asem=dp# Ora Tulis 3G-SDI *asem=sdi# Ora Tulis Sistem Smart * sour=smartsystem# Ora Waca Sumber saiki *asem=?# Ya Kontrol Audio Tulis Mute Aktif *mute=on# Ya Nulis Mute Off *mute=mati# Ya Waca Status Mute *mute=?# Ya Tulis Volume + *vol=+ # Ya Tulis Volume - *vol=-# Ya Tulis Tingkat volume kanggo pelanggan *vol=nilai# Ya Waca Status Volume *vol=?# Ya Tulis Mic. Volume + *micvol=+# Ya Tulis Mic. Volume - *micvol=-# Ya Waca Mic. Status Volume *micvol=?# Ya Sumber audio pilih Tulis Audio pass Through mati *audiosour=mati# Ya Tulis Audio-Komputer1 *audiosour=RGB# Ya Tulis Audio-Komputer2 *audiosour=RGB2# Ora Tulis Audio-Video/S-Video *audiosour=vid# Ora Tulis Komponen Audio *audiosour=ypbr# Ora Tulis Audio-HDMI *audiosour=hdmi# Ya Tulis Audio-HDMI2 *audiosour=hdmi2# Ya Tulis Audio-HDMI3 *audiosour=hdmi3# Ora Tulis DisplayPort *audiosour =dp# Ya Tulis HDBaseT *audiosour=hdbaset# Ya Tulis Mikropon *audiosour=mikrofon# Ya Waca Audio pass Status *audiosour=?# Ya Mode Gambar Tulis Dinamis *appmod=dinamis# Ora Tulis Presentasi *appmod=preset# Ya Tulis sRGB *appmod=srgb# Ya Tulis Padhang *appmod= padhang# Ya Tulis Ruang Tamu *appmod=ruang tamu# Ora Tulis Game *appmod=game# Ora Tulis Bioskop(Rec. amp native *ct=native# No Read Color Temperature Status *ct=?# Yes Write Aspect 4:3 *asp=4:3# Yes Write Aspect 16:6 *asp=16:6# No Write Aspect 16:9 *asp=16:9# Yes Write Aspect 16:10 *asp=16:10# Yes Write Aspect 2.35:1 *asp=2.35# No Write Aspect Auto *asp=AUTO# Yes Write Aspect Real *asp=REAL# No Write Aspect Letterbox *asp=LBOX# No Write Aspect Wide *asp=WIDE# No Write Aspect Anamorphic *asp=ANAM# No Write Aspect Anamorphic 2.35 *asp=ANAM2.35# No Write Aspect Anamorphic 16:9 *asp=ANAM16:9# No Write Aspect 2.4:1 *asp=2.4# No Read Aspect Status *asp=?# Yes Write Vertical Keystone + *vkeystone=+# Yes Write Vertical Keystone - *vkeystone=-# Yes Write Set Vertical Keystone value *vkeystone=value# Yes Read Vertical Keystone value *vkeystone=?# Yes Write Horizontal Keystone + *hkeystone=+# Yes Write Horizontal Keystone - *hkeystone=-# Yes Write Set Horizontal Keystone value *hkeystone=value# Yes Read Horizontal Keystone value *hkeystone=?# Yes Write Overscan Adjustment + *overscan=+# No Write Overscan Adjustment - *overscan=-# No Read Overscan Adjustment value *overscan=?# No Write 4 Corners Top-Left-X Decrease *cornerfittlx=-# Yes Write 4 Corners Top-Left-X Increase *cornerfittlx=+# Yes Read 4 Corners Top-Left-X Status *cornerfittlx=?# Yes Write 4 Corners Top-Left-Y Decrease *cornerfittly=-# Yes Write 4 Corners Top-Left-Y Increase *cornerfittly=+# Yes Read 4 Corners Top-Left-Y Status *cornerfittly=?# Yes Write 4 Corners Top-Right-X Decrease *cornerfittrx=-# Yes Write 4 Corners Top-Right-X Increase *cornerfittrx=+# Yes Read 4 Corners Top-Right-X Status *cornerfittrx=?# Yes Write 4 Corners Top-Right-Y Decrease *cornerfittry=-# Yes Write 4 Corners Top-Right-Y Increase *cornerfittry=+# Yes Read 4 Corners Top-Right-Y Status *cornerfittry=?# Yes Write 4 Corners Bottom-Left-X Decrease *cornerfitblx=-# Yes Write 4 Corners Bottom-Left-X Increase *cornerfitblx=+# Yes Read 4 Corners Bottom-Left-X Status *cornerfitblx=?# Yes Write 4 Corners Bottom-Left-Y *cornerfitbly=-# Yes Decrease Write 4 Corners Bottom-Left-Y Increase *cornerfitbly=+# Yes Read 4 Corners Bottom-Left-Y Status *cornerfitbly=?# Yes Write 4 Corners Bottom-Right-X Decrease *cornerfitbrx=-# Yes Write 4 Corners Bottom-Right-X Increase *cornerfitbrx=+# Yes Read 4 Corners Bottom-Right-X Status *cornerfitbrx=?# Yes Write 4 Corners Bottom-Right-Y Decrease *cornerfitbry=-# Yes Write 4 Corners Bottom-Right-Y Increase *cornerfitbry=+# Yes Read 4 Corners Bottom-Right-Y Status *cornerfitbry=?# Yes Write Digital Zoom In *zoomI# Yes Write Digital Zoom out *zoomO# Yes Write Auto *auto# Yes Write Brilliant color + *BC=+# Yes Write Brilliant color - *BC=-# Yes Write Brilliant color set value *BC=value# Yes Read Brilliant color status *BC=?# Yes Write Auto(HDR) *hdr=auto# No Write SDR *hdr=sdr# No Write HDR10 *hdr=hdr# No Write HLG *hdr=hlg# No Write HDR status *hdr=?# No Write Reset current picture *rstcurpicsetting# No settings Write Reset all picture settings *rstallpicsetting# No Write Reset picture settings *rstpicsetting# Yes Operation Settings Write Projector Position-Front Table *pp=FT# Yes Write Projector Position-Rear Table *pp=RE# Yes Write Projector Position-Rear Ceiling *pp=RC# Yes Write Projector Position-Front Ceiling *pp=FC# Yes Read Projector Position Status *pp=?# Yes Write Quick cooling on *qcool=on No Write Quick cooling off *qcool=off No Read Quick cooling status *qcool=? amp Kontrol Waca Lamp Jam *ltim=?# Ya Waca Lamp2 Jam *ltim2=?# Ora Tulis Mode Normal *lampm=lnor# Ya Tulis mode Eco *lampm=eco# Ya Tulis mode SmartEco *lampm=seco# Ora Tulis mode SmartEco 2 *lampm= seco2# Ora Nulis mode SmartEco 3 *lampm= seco3# Ora Tulis Mode Dimming *lampm=dimming# Ora Nulis Mode khusus *lampm=custom# Ya Tulis tingkat Cahya kanggo mode khusus *lampcustom=value# Ya Waca status level Cahya kanggo mode khusus *lampadat=?# Ya Tulis (dual lamp) Dual Padhang * lampm = dualbr# Ora Tulis (dual lamp) Dwi Reliable * lampm = dualre# Ora Tulis (dual lamp) Alternatif Tunggal * lampm = tunggal# Ora Tulis (ganda lamp) Eko Alternatif Tunggal * lampm = singleeco# Ora Waca Lamp Status Mode *lampm=?# Ya Aneka Maca Jeneng Model *modelname=?# Ya Maca Sistem F/W Versi *sysfwversion=?# Ya Maca Scaler Versi F/W *scalerfwversion=?# Ya Maca Format F/W Versi *formatfwversion=?# Ora Waca Versi Lan F/W *lanfwversion=?# Ya Waca Versi MCU F/W *mcufwversion=?# Ya Waca Versi Ballast F/W *ballastfwversion=?# Ora Tulis Blank On *blank=on# Ya Tulis Kosong * blank=mati# Ya Waca Status Kosong *kosong=?# Ya Tulis Beku Aktif *beku=on# Ya Tulis Beku Mati *beku=mati# Ya Waca Status Beku *beku=?# Ya Tulis Menu Ing *menu=on# Ya Tulis Menu Mati *menu=mati# Ya Waca Status Menu *menu=?# Ya Tulis *munggah# Ya Tulis *mudhun# Ya Tulis Nengen *tengen# Ya Tulis Ngiwa *kiwa# Ya Tulis Ketik *ketik# Ya Tulis Mbalik *kembali# Ya Tulis Menu Sumber Aktif *sourmenu=on# Ya Tulis Menu Sumber Mati *sourmenu=mati# Ya Waca Status Menu Sumber *sourmenu=?# Ya Tulis Sinkronisasi 3D Mati *3d=mati# Ya Tulis 3D Otomatis *3d= otomatis# Ya Tulis 3D Sync Ndhuwur Ngisor *3d=tb# Ya Tulis 3D Sync Frame Sequential *3d=fs# Ya Tulis 3D Frame packing *3d=fp# Ya Tulis 3D Side by side *3d=sbs# Ya Tulis 3D inverter mateni *3d=da# Ya Tulis inverter 3D *3d=iv# Ya Tulis 2D menyang 3D *3d=2d3d# Ora Tulis 3D nVIDIA *3d=nvidia# Ora Waca Status Sinkronisasi 3D *3d=?# Ya Tulis Remote Receiver On *rr =on# No Write Remote Receiver Off *rr=off# No Write Remote Receiver-ngarep+mburi *rr=fr# Ora Write Remote Receiver-ngarep *rr=f# Ora Write Remote Receiver-mburi *rr=r# Ora Write Remote Receiver-top *rr=t# Ora Tulis Remote Receiver-ndhuwur+ngarep *rr=tf# Ora Tulis Remote Receiver-top+mburi *rr=tr# Ora Waca Remote Receiver Status *rr=?# Ora Tulis Instan On-on *ins=on# Ora Tulis Instan On-off *ins=off# Ora Waca Instan On Status *ins=?# Ora Tulis Lamp Mode Saver-on *lpsaver=on# Ora Tulis Lamp Saver Mode-off *lpsaver=off# Ora Waca Lamp Status Mode Saver *lpsaver=?# Ora Nulis Proyeksi Log In Kode ing *prjlogincode=on# Ora Nulis Proyeksi Log In Kode mati *prjlogincode=mati# Ora Waca Proyeksi Log In Kode Status *prjlogincode=?# Ora Nulis Siaran ing *broadcasting =on# Ora Tulis Siaran mati *broadcasting=mati# Ora Waca Status Siaran *siaran=? No Write AMX Device Discovery-on *amxdd=on# Yes Write AMX Device Discovery-off *amxdd=off# Yes Read AMX Device Discovery Status *amxdd=?# Yes Read Mac Address *macaddr=?# Yes Read Serial Number *serial number=?# Yes Write High Altitude mode on *Highaltitude=on# Yes Write High Altitude mode off *Highaltitude=off# Yes Read High Altitude mode status *Highaltitude=?# Yes Installation Write Load Lens memory 1 *lensload=m1# No Write Load Lens memory 2 *lensload=m2# No Write Load Lens memory 3 *lensload=m3# No Write Load Lens memory 4 *lensload=m4# No Write Load Lens memory 5 *lensload=m5# No Write Load Lens memory 6 *lensload=m6# No Write Load Lens memory 7 *lensload=m7# No Write Load Lens memory 8 *lensload=m8# No Write Load Lens memory 9 *lensload=m9# No Write Load Lens memory 10 *lensload=m10# No Read Read Lens memory status *lensload=?# No Write save Lens memory 1 *lenssave=m1# No Write save Lens memory 2 *lenssave=m2# No Write save Lens memory 3 *lenssave=m3# No Write save Lens memory 4 *lenssave=m4# No Write save Lens memory 5 *lenssave=m5# No Write save Lens memory 6 *lenssave=m6# No Write save Lens memory 7 *lenssave=m7# No Write save Lens memory 8 *lenssave=m8# No Write save Lens memory 9 *lenssave=m9# No Write save Lens memory 10 *lenssave=m10# No Write Reset Lens to center *lensreset=center# No Color Calibration Write Tint + *tint=+# Yes Write Tint - *tint=-# Yes Write Set Tint value *tint=value# Yes Read Get Tint value *tint=?# Yes Write Set gamma value *gamma=value# Yes Read Gamma value status *gamma=?# Yes Write Set HDR Brightness value *hdrbri=value# Yes Read Get HDR Brightness value *hdibri=?# Yes Write Red Gain + *RGain=+# Yes Write Red Gain - *RGain=-# Yes Write Set Red Gain value *RGain=value# Yes Read Get Red Gain value *RGain=?# Yes Write Green Gain + *GGain=+# Yes Write Green Gain - *GGain=-# Yes Write Set Green Gain value *GGain=value# Yes Read Get Green Gain value *GGain=?# Yes Write Blue Gain + *BGain=+# Yes Write Blue Gain - *BGain=-# Yes Write Set Blue Gain value *BGain=value# Yes Read Get Blue Gain value *BGain=?# Yes Write Red Offset + *ROffset=+# Yes Write Red Offset - *ROffset=-# Yes Write Set Red Offset value *ROffset=value# Yes Read Get Red Offset value *ROffset=?# Yes Write Green Offset + *GOffset=+# Yes Write Green Offset - *GOffset =-# Yes Write Set Green Offset value *GOffset=value# Yes Read Get Green Offset value *GOffset=?# Yes Write Blue Offset + *BOffset=+# Yes Write Blue Offset - *BOffset=-# Yes Write Set Blue Offset value *BOffset=value# Yes Read Get Blue Offset value *BOffset=?# Yes Write Primary Color *primcr=value# Yes Read Primary Color Status *primcr=?# Yes Write Hue + *hue=+# Yes Write Hue - *hue=-# Yes Write Set Hue value *hue=value# Yes Read Get Hue value *hue=?# Yes Write Saturation + *saturation=+# Yes Write Saturation - *saturation=-# Yes Write Set Saturation value *saturation=value# Yes Read Get Saturation value *saturation=?# Yes Write Gain + *gain=+# Yes Write Gain - *gain=-# Yes Write Set Gain value *gain=value# Yes Read Get Gain value *gain=?# Yes Write Color Gamut Auto *cgamut=auto# No Write Color Gamut BT.709 *cgamut=bt.709# No Write Color Gamut BT.2020 *cgamut=bt.2020# No Write Color Gamut DCI-P3 *cgamut=dci-p3# No Read Color Gamut Value *cgamut=?# No Write Dynamic Iris ON *diris=on# No Write Dynamic Iris OFF *diris=off# No Read Dynamic Iris status *diris=?# No Write Color Calibration Save *colorsave# No Write Color Calibration pattern display *colorpattern=value# No Note: The above function will be varied from model to model. FAQ Video Kepiye cara nggunakake kabel RS232 kanggo nindakake kontrol volume lan kontrol swara ing proyektor? https://youtu.be/P4F26kEv60U How to use RS232 cable connection to power on & off projector? https://youtu.be/faGUvcDBmJE How to set up RS232 cable connection? https://youtu.be/CYJRqyO6K1w How to use RS232 command to request fan speed and temperature value? https://youtu.be/KBXEd-BCDKQ BenQ.com © 2023 BenQ Corporation All rights reserved. Hak modifikasi dilindhungi undhang-undhang.

Temokake spesifikasi rinci lan pandhuan panggunaan kanggo 85 056 Garden and Pathway Luminaire kanthi PIR Motion and Light Sensor dening BEGA. Sinau babagan wattage, flux luminous, pedoman instalasi, lan carane ngatur sensor PIR terpadu liwat app BEGA Smart.

Nggoleki Lampu Sensor Lampu Kab Dokumen miturut Jeneng Model utawa Nomer:

Tag Arsip: Lampu Sensor Lampu Kab

BEGA 85 056 Garden and Pathway Luminaire kanthi PIR Motion and Light Sensor Instruction Manual