Surenoo SLG320240E Graphic LCD Module

Spesifikasi dhasar

 Spesifikasi Tampilan

1. Mode Tampilan LCD: FSTN, Positif, Transflective
2. Display Color : Display Data = “1” : Dark Gray (*1) : Display Data = “0” : Light Gray (*2)
3. Viewing Angle: 9 H
4. Cara nyopir: 1/240 tugas, 1/12 bias
5. Lampu latar: Lampu latar LED putih

Cathetan:

1. Color tone may slightly change due to Temperature and Driving conditions.
2. Werna ditetepake minangka warna ora aktif / latar mburi

Spesifikasi Mekanik

1. Outline Dimension: 99.5 x 71.75 x 10.4 MAX. (exclude FFC terminal) see attach

Diagram Blokir

GAMBAR OUTLINE

Fungsi Terminal

cathetan:

1. If there is no read-write activity, /WAIT will be in HZ state.

GAMBAR OUTLINE

Ratings maksimum Absolute

Ati-ati:
Any Stresses exceeding the Absolute Maximum Ratings may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied, and prolonged exposure to extreme conditions may affect device reliability

Karakteristik Listrik

Karakteristik Sirkuit Lampu Latar LED

Ati-ati:
Ngluwihi arus nyopir sing disaranake bisa nyebabake karusakan gedhe ing lampu latar lan nyepetake umure.

Karakteristik AC

 8080 Mode

Cathetan:

1. Ts = System clock period
2. t4min = 2Ts + 5
3. t11max = 1Ts + 7 (for 5.0V)
4. t12min = 1Ts (for a read cycle followed by a read or write cycle) = 2Ts + 2 (for a write cycle followed by a write cycle) = 5Ts + 2 (for a write cycle followed by a read cycle)
5. t13max = 4Ts + 2
6. Input signal rise/fall time should be less than 4.5ns
7. For details, please see the S1D13700 data sheet

Reset Wektu

cathetan:

1. A delay is required after exiting power save mode. Writing the SYSTEM SET command will exit power save mode and start the internal oscillator.
2. It requires a reset pulse after power-on to re-initialize its internal state.

Spesifikasi Fungsi

Nyetel Kontras Tampilan
A variable resistor must be connected to the LCD module to provide a reference to V0. Adjusting the VR will result a change of LCD contrast. The recommended value of VR is 25k to 50k

Ngreset modul LCD
The LCD module should be initialized by a hardware reset, using the/RES terminal.

Fungsi Jumper
 Interfacing Setting

Clock Divider Setting

Display Pixel Map

Cathetan:

1. Based on the top view of the LCD module, the 1, 1 (x, y) pixel is the upper-left pixel; the 320, 240 (x, y) pixel is the lower-right pixel.
2. For the details of memory mapping, please refer to the S1D137009 datasheet.

Ringkesan Command

Cathetan:
For details, please refer to the S1D13700 datasheet.

Initialization Setting Example
The following settings should be issued tothe  LCD module after a hardware reset. (Example could be adjusted if necessary.)

Cathetan:
For details, please refer to the S1D13709 datasheet.

Desain lan Penanganan Pancegahan

1. The LCD panel is made of glass. Any mechanical shock (eg, dropping from a high place) will damage the LCD module.
2. Do not add excessive force on the surface of the display, which may cause the Display color to change abnormally.
3. The polarizer on the LCD is easily scratched. If possible, do not remove the LCD protective film until the last step of installation.
4. Aja nyoba mbongkar utawa ngolah maneh modul LCD.
5. Only Clean the LCD with Isopropyl Alcohol or Ethyl Alcohol. Other solvents (eg, water) may damage the LCD.
6. When mounting the LCD module, make sure that it is free from twisting, warping, and distortion.
7. Ensure to provide enough space (with a cushion) between the case and LCD panel to prevent external force from being added to it, or it may cause damage to the LCD or degrade the display result.
8. Mung nyekel modul LCD ing sisih. Aja nahan modul LCD kanthi nambah kekuwatan ing segel panas utawa TAB.
9. Never add force to the component of the LCD module. It may cause invisible damage or a degradation of the reliability.The
10. Modul LCD bisa gampang rusak amarga listrik statis. Ati-ati kanggo njaga lingkungan kerja anti-statis sing paling optimal kanggo nglindhungi modul LCD.
11. When peeling off the protective film from the LCD, static charge may cause an abnormal display pattern. It is normal and will resume to normal in a short while.
12. Take care and prevent getting hurt by the LCD panel’s sharp edge.
13. Aja operate modul LCD ngluwihi rating maksimum absolut.
14. Keep the signal line as short as possible to prevent a noisy signal from affecting to LCD module.
15. Never apply a signal to the LCD module without a power supply.The
16. IC chip (eg, TAB or COG) is sensitive to the light. A strong lighting environment could cause a malfunction. Light sealing structure casing is recommended.
17. Reliabilitas modul LCD bisa suda amarga kejut suhu.
18. When storing the LCD module, avoid exposure to direct sunlight, high humidity, high temperature, or low temperature. They may damage or degrade the LCD module

INFORMASI LAIN

• Shenzhen Surenoo Technology Co., Ltd.
• www.surenoo.com

FAQ

Q: Can the display color be adjusted?

A: The display color is predefined as Dark Gray for Display Data = 1 and Light Gray for Display Data = 0, which cannot be adjusted.

Q: Is there a way to adjust the viewing sudut?

A: Ing viewing angle is fixed at 9 H and cannot be manually adjusted.

Dokumen / Sumber Daya

Surenoo SLG320240E Graphic LCD Module [pdf] Manual pangguna SLG320240E, SLG320240E Graphic LCD Module, Graphic LCD Module, LCD Module, Module

Referensi

• Manual pangguna