LANCOM Systems ON-D8a Lancom AirLancer
Swaraview of the mounting kit
- 1 connection flange (A)
- 1 connection arm (B)
- 1 pole flange / wall bracket (C)
- 4 washers M6 (D)
- 4 spring washers M6 (E)
- 4 nuts M6 (F)
- 1 pole clamp for pole diameter up to 62.5 mm (I)
- 2 hexagon head screws M8x35 (J)
- 4 spring washers M8 (K)
- 4 washers M8 (L)
- 2 nuts M8 (M)
- 2 hexagon head screws M8x70 (N)
Ora kalebu ing ruang lingkup pangiriman
2 kabamps for pole diameter > 62.5 mm (H)
Mounting the antenna flange and connection arm
Screw the connection flange (A) to the back of the antenna housing using the enclosed washers (D), spring washers (E), and nuts (F). Make sure that the spring washers (E) are located directly under the nuts (F).
Then fasten the connection arm (B) hand-tight to the connection flange (A) using a screw (J), a spring washer (K), a washer (L), and a nut (M). Make sure that the spring washer (L) is located directly under the screw head.
Preparation kanggo tembok soyo tambah
Yen sampeyan pengin masang antena ing tembok, nggunakake wall mount (C) minangka cithakan pengeboran kanggo tandha bolongan pengeboran kanggo tembok soyo tambah.
Bor bolongan sing cocog ing tandha lan lebokake dowels (ora kalebu) yen perlu. Gumantung ing materi tembok lan kondisi, ambane lan diameteripun bolongan kudu diatur.
Pemasangan antena ing tembok
- Selarasake krenjang tembok kanthi bolongan pengeboran lan kencengake nganggo sekrup sing cocog.
- Now hand-tighten the connection arm (B) already mounted on the connection flange (A) to the wall bracket (C) using a screw (J), a spring washer (K), a washer (L), and a nut (M).
- Make sure that the spring washer (K) is located directly under the screw head and that the arrow on the back of the antenna housing is pointing upwards.
- Selarasake antena miturut kekarepan sampeyan banjur kencengake sekrup lengen sambungan kanthi torsi sing cocog.
Pole soyo tambah saka antena
Position the pole flange (C) at the desired height on a suitable pole with sufficient load-bearing capacity. Use the pole clamp (I) to attach to poles up to 62.5 mm in diameter.
- Fasten the pole clamp (I) to the pole flange (C) using the two screws (N), the spring washers (K), and the washers (L). Please note that the mast clamp must be rotated depending on the mast diameter.
- For pole diameters over 62.5 mm, you need suitable band clamps (H) (not included in the scope of delivery) and guide them through the pole flange and around the pole as shown in the overview
and tighten them after you have aligned the pole flange.
- Then connect the pole flange (C) hand-tight to the connection arm (B) already mounted on the antenna using an enclosed screw (J), a spring washer (K), a washer (L), and a nut (M).
- Make sure that the spring washer (K) is located directly under the screw head and that the arrow on the back of the antenna housing is pointing upwards.
- Selarasake antena miturut syarat sampeyan banjur kencengake sekrup lengen sambungan kanthi torsi sing cocog.
Informasi penting
- Nangani tanggung jawab frekuensi dhuwur
Kanggo tundhuk karo syarat proteksi EU Directive 2014/53 lan EN 62479 babagan watesan dhasar kanggo safety wong ing lapangan elektromagnetik lan "Kabijakan FCC babagan Eksposur Manungsa menyang Medan Elektromagnetik Frekuensi Radio", perlu dikonfigurasi. gain antena bener ing router WLAN utawa titik akses WLAN. - Undhang-undhang Peralatan Listrik lan Elektronik
Aja mbuwang sampah listrik lan elektronik ing sampah rumah tangga, sing ora bisa didaur ulang. Priksa manawa sampah listrik lan elektronik sampeyan dibuwang sesuai karo pedoman negara sampeyan saiki. - Penanganan kabel antena sing bener
Kabel antena minangka kabel RF sing sensitif. Nalika mbikak mau, iku penting kanggo mesthekake yen kabel ora kinked lan mbengkongaken minangka sethitik sabisa, amarga iki bisa kasil mundhut ing syarat-syarat kinerja antena. Kajaba iku, kabel antena ora kena dilebokake ing puteran kabel sing nyenyet. - Gain antena lan mungkasi port antena sing ora digunakake ing titik akses
Sambungan antena sing ora digunakake ing jalur akses kudu diakhiri nganggo antena rod sing ditutup. Kanggo titik akses njero ruangan, resistor terminating sing kalebu adaptor AirLancer AN-RPSMA-NJ bisa digunakake. Kajaba iku, gain antena kudu ditemtokake ing konfigurasi titik akses.
data teknis
- Rentang frekuensi 4,900 - 5,900 MHz
Karakteristik antena
- Radiation patterns Horizontally: 8° Vertically: 8°
- Recommended use Point-to-Point
- VSWR 2.0:1 max.
- Gain 21 dBi max.
Data Mekanik
- Ukuran (mm) 370 x 370 x 30 (W x H x D)
- Weight 1,800 g (Antenna without mounting kit)
- Suhu operasi -40 ° C nganti 85 ° C
- Color Light grey
- Material UV resistant plastic
- Mounting options Wall- and pole mounting, alignable
- Cables & Connectors 2x 100 cm ULA100 cable with N-Plug connector
Item
- Garansi 2 taun kanggo AirLancer lan aksesoris
- Item no. 61708
- Scope of delivery Antenna, 2 connection cables, mounting kit for wall and pole mounting
LANCOM Systems GmbH
Perusahaan Rohde & Schwarz Adenauerstr. 20/B2
52146 Wuerselen | Jerman
info@lancom.de | lancom-systems.com
LANCOM, LANCOM Systems, LCOS, LANcommunity, LANCOM Service LANcare, LANCOM Active Radio Control, and AirLancer are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omis-
sions. 111436 09/2025
Pitakonan sing Sering Ditakoni
P: Apa sing kudu ditindakake yen sawetara bagean ilang saka paket kasebut?
A: Hubungi dhukungan pelanggan kanggo pitulungan entuk bagean sing ilang.
Q: How do I ensure proper alignment of the antenna during mounting?
A: Follow the provided instructions carefully and use appropriate tools to align the antenna as needed.
Dokumen / Sumber Daya
 |
LANCOM Systems ON-D8a Lancom AirLancer [pdf] Instruksi Manual ON-D8a Lancom AirLancer, ON-D8a, Lancom AirLancer, Lancom, AirLancer |