Isine ndhelikake
1 PHILIPS DDC116-UL Solusi Kontrol Pencahayaan Arsitektur Sistem Tunggal
2 Pandhuan Panggunaan Produk
3 Nyepetake desain kontrol cahya lan instalasi
4 Solusi pemasangan fleksibel
5 Kontrol cahya digawe prasaja
6 Fungsi sing kasedhiya
7 Sistem example
8 Kode pesenan
9 Pitakonan sing Sering Ditakoni
10 Dokumen / Sumber Daya
10.1 Referensi

PHILIPS-LOGO

PHILIPS DDC116-UL Solusi Kontrol Pencahayaan Arsitektur Sistem Tunggal

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-PRODUCT

Spesifikasi Produk

  • Relay switching kapasitas dhuwur: 16 A beban cahya, 20 A beban umum
  • Cocog kanggo panggunaan plenum: UL 2043 lan Chicago dirating
  • Input kontak garing kanggo input darurat utawa tambahan UL 924
  • Vol universaltage: 100-277 VAC
  • Choice of control protocol: DyNet utawa DMX512
  • Standalone control of up to five lighting zones plus plug load

Pandhuan Panggunaan Produk

Nyiyapake Piranti SSA
Follow these steps to set up the Single System Architecture devices:

  1. Priksa manawa sumber daya wis pedhot sadurunge instalasi.
  2. Connect the devices using dual RJ45 connectors or wire to spring terminals.
  3. Refer to the user manual for specific configurations based on the device model.

Konfigurasi Controller
Kanggo ngatur controller, tindakake langkah iki:

  1. Ngakses setelan pengontrol DDC116-UL.
  2. Adjust the DIP switches and button settings as required for your lighting control functionality.
  3. Refer to the specific settings for different functionalities provided in the user manual.

Fitur Sistem Swaraview
The system offers various features for efficient lighting control:

  • High capacity switching relay for lighting and general loads.
  • Easy installation with plug-in RJ45 sockets and push-down terminals.
  • Daisy chain piranti tambahan kanggo kontrol ditambahi.

Nyepetake desain kontrol cahya lan instalasi

Ngenalake DDC116-UL, jantung solusi kontrol pencahayaan Philips Dynalite SSA (Arsitektur Sistem Tunggal). Sistem kasebut menehi daya installer listrik kanggo nggawe fungsi kontrol cahya kanthi cepet lan gampang nganggo switch DIP lan setelan tombol. Metu saka kothak, sistem ndhukung 0-10 V dimming lan reconfigurable kanggo DALI broadcast dimming, nggawe solusi iki mangsa-bukti.
The system enables customers to configure different areas and network specific devices together for code-compliant lighting control functionality without requiring commissioning software. Optionally, customers can use System Builder commissioning software to integrate with a Building Management System over BACnet or to be part of a larger-scale system solution.

Fitur sistem

Relay switching kapasitas dhuwur
16 A beban cahya.
20 Beban umum (beban plug).

Cocog kanggo panggunaan plenum
UL 2043 lan Chicago dirating kanggo instalasi ing ruang plenum penanganan udhara. Cocog karo omah kothak prapatan standar.

Input kontak garing
Kanggo input darurat utawa tambahan UL 924.

Vol universaltage
100-277 VAC.

Pilihan saka protokol kontrol
Bisa dikontrol liwat DyNet utawa DMX512.

Gampang kanggo nginstal
Pasang soket RJ45 lan terminal push-mudhun.

Fleksibel
Kontrol 0-10 V 100 mA Sink utawa Sumber lan siaran DALI. Dijamin saiki 100 mA, Maksimum 250 mA beban.

piranti Daisy chained
Sambungake pengontrol tambahan lan piranti SSA liyane nggunakake konektor RJ45 dual utawa kabel menyang terminal spring.

Mandiri utawa jaringan
Kontrol mandiri nganti limang zona cahya ditambah beban plug. Bisa jaringan kanggo proyek sing luwih gedhe.

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (1)

Solusi pemasangan fleksibel

Desain sing dirating plenum kompak kompatibel karo skema kabel kothak prapatan standar, nyuda biaya instalasi lan biaya proyek.

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (2) PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (3)

  •  Standar AUX/UL924 Biasane Ditutup (Bukak = Aktif).
    Copot kabel jumper ing antarane terminal GND lan AUX/UL924 yen nyambung menyang darurat utawa sistem liyane.
  • Kanggo DMX512, nambah 120 Ohm, 0.5 W resistor mandap tengen D + lan D- ing piranti DMX512 pungkasan.

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (4)

Pemasang diwenehi wewenang kanggo nyedhiyakake layanan lengkap kanthi nyetel fungsi kontrol lampu.

Kontrol cahya digawe prasaja

Komponen Arsitektur Sistem Tunggal

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (5)

Kanggo informasi luwih lengkap babagan instalasi, deleng instruksi instalasi piranti individu.

Piranti sing dikonfigurasi installer

  • DDC116-UL – Single zone 0-10 V/DALI broadcast and relay controller.
  • DINGUS-UI-RJ45-DUAL lan DINGUS-DUS-RJ45-DUAL
    – Quick connections between different wall stations and sensors.
  • PAxBPA-SSA - stasiun tembok 2, 4 utawa 6 tombol kanthi pitung pilihan label.
  • DACM-SSA - Modul komunikasi antarmuka pangguna kanthi 15 konfigurasi.
  • DUS360-DA-SSA - sensor gerak PIR lan awan kanthi konfigurasi sing bisa dipilih liwat switch DIP
  • DUS804CS-UP-SSA – Ultrasonic motion (occupancy or vacancy).

The basic system caters for all typical lighting applications such as corridors, classrooms, open and enclosed offices, meeting rooms, function rooms, and foyers.

Fungsi sing kasedhiya

Sensor

  • Bisa dikonfigurasi ing antarane mode Occupancy (standar) utawa mode Vacancy.
  • Pilihan deteksi gerakan inframerah utawa ultrasonik pasif.
  • Wektu entek sing bisa dikonfigurasi 5, 10, 15, lan 20 menit (standar).
    • Wektu tenggang 1 menit ing kabeh wektu entek.
    • Mode saksi 1 jam kanggo nguji fungsi.
  • Dibangun ing wayah awan panen.
  • Fleksibilitas kanggo ngaktifake zona awan primer lan sekunder.

Mode Occupancy - Lampu urip yen ana gerakan, lampu mati sawise wektu entek yen ora ana gerakan.
Vacancy mode – Lights are manually turned on from
the switch and turn off after the timeout period if there is no motion.
Zona awan utama - Zona jendhela langsung ing sangisore sensor.
Zona cahya awan sekunder - Zona sing luwih adoh saka jendhela kanthi offset 20% luwih padhang.

Stasiun tembok

  • Ngontrol siji utawa kabeh limang zona cahya lan zona beban plug.
  • Kelingan adegan cahya sing wis disetel.
  • Tombol intuisi sing prasaja.
  • Ramptombol ing mung mengaruhi zona sing aktif.

Pengontrol beban
The SSA is oriented around the DDC116-UL’s configurability via its network sign-on button (service switch) without requiring computer-based commissioning tools. This simplifies the activation process, saving commissioning costs and labor charges. Multiple DDC116-ULs can be connected into a single system to meet the needs of a single area with multiple lighting groups, daylight harvesting zones, and plug loads.
The internal relay saves power by automatically switching off the circuit when lighting loads are dimmed to zero.

Sistem example

– classroom application

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (6)

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (8)

Floor Zones

  1. Screen/Presentation zone (default)
  2. Generic Lighting Primary Zone
  3. Generic Lighting Primary Daylight Zone
  4. beban plug

Langkah 1
Nemtokake DDC116-UL menyang zona tengen

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (9)

Nyetel piranti Arsitektur Sistem Tunggal
Ing telung langkah, sampeyan bisa langsung nyiyapake piranti kanggo nggunakake daya kontrol cahya jaringan.

Konfigurasi controller
Nemtokake controller menyang salah siji saka enem zona karo tumindak push-tombol prasaja.

Fungsi ngalih layanan

  • 1 push singkat – Kirim ID jaringan
  • 3 push cendhak - Setel lampu dadi 100%
  • 4 short pushes – Test mode (LED blinking pattern changes and lights flash for 5 minutes)
    • 1 short push – Toggle control type between 0-10 V (Red LED) and DALI Broadcast (Green LED).
    • Tekan terus 4 detik – Simpen jinis kontrol lan metu saka Mode Tes.

Push and hold for 4 seconds – Program Mode (Blue LED flash count indicates the controller zone assignment). Program Mode times out after 30 seconds of inactivity, discarding changes.

  • Short push – Cycle through zone numbers (after each push, the flash count indicates the controller zone assignment). Zone 1 = Screen/Presentation Zone (default)
    • Zona 2 = Zona Utama Cahya Umum
    • Zona 3 = Cahya Umum Zona Sekunder
    • Zona 4 = Cahya Umum Zona Awan Utama
    • Zona 5 = Cahya Umum Zona Awan Sekunder (20% luwih padhang)
    • Zona 6 = Zona Muatan Plug
  • Pencet terus nganti 4 detik - Simpen owah-owahan lan metu saka Mode Program. Piranti urip maneh lan siyap kanggo miwiti karya!

Service LED indikasi 

  • abang: Output type = 0-10 V.
  • ijo: Output type = DALI Broadcast.
  • alon: 1 flash per second when device is idle.
  • Sedheng: 2 flashes per second when DyNet bus is busy.
  • cepet: 3 flashes per second when a message is addressed to the controller.
  • Sedheng: 2 flashes per second, alternating red and blue when in emergency mode.

Langkah 2
Konfigurasi sensor

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (10)

Projects can choose between a PIR or dual-technology PIR and ultrasonic motion sensor. Ultrasonic sensors are available in occupancy or vacancy mode. Timeouts can be set for specific projects and multiple sensors can be used together to cover larger areas”. The inbuilt light sensor on the PIR sensor can also be used for daylight-based dimming (daylight harvesting).

DUS360CR-DA-SSA Settings (standar)

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (11)

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (12)

DUS804CS-UP-SSA-O/V Setelan Ultrasonik

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (13)

Wektu entek standar 20 menit utawa entuk setelan entek saka DUS360CR-DA-SSA yen digunakake bebarengan.

Loro strategi kontrol sing beda kasedhiya:

  • Occupancy mode response – Auto on & Auto off.
  • Vacancy mode response – Manual on & Auto off.

*Sensor ultrasonik kudu diselehake paling sethithik 60ft (18 m) supaya ora sesambungan.

Langkah 3
Konfigurasi stasiun tembok karo DACM

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (17)

15 Konfigurasi stasiun
Setel saklar DACM DIP kanggo milih fungsi tombol sing dibutuhake.

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (14)

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (15)

PHILIPS-DDC116-UL-Single-System-Architecture-Lighting-Control-Solution-FIG- (16)

Kode pesenan

Arsitektur Sistem Tunggal

kode bagean Dynalite Katrangan 12NC
DDC116-UL 1 x 0-10 V utawa DALI controller siaran karo output daya ngalih. 913703376709
DUS360CR-DA-SSA PIR gerak lan PE sensor cahya wis diprogram kanggo Occupancy utawa Lowongan. 913703389909
DUS804CS-UP-SSA-O Gerakan ultrasonik, sensor gerak PIR sing wis diprogram kanggo Occupancy. 913703662809
DUS804CS-UP-SSA-V Gerakan ultrasonik, sensor gerak PIR sing wis diprogram kanggo Lowongan. 913703662909
DACM-DyNet-SSA Modul komunikasi antarmuka pangguna sing wis diprogram kanggo Arsitektur Sistem Tunggal. 913703668809
PA4BPA-WW-L-SSA-onoff-ramp Antumbra 4 Button NA Rampung putih (Ngaktifake / Mati / Munggah / Ngisor). Konfigurasi 0-5. 913703253109
PA6BPA-WW-L-SSA-prasetel-ramp Antumbra 6 Button NA Rampung putih (Aktif / Off / Sedheng / Kurang / Munggah / Ngisor). Konfigurasi 6. 913703253209
PA6BPA-WW-L-SSA-AV-ramp Antumbra 6 Button NA Rampung putih (Aktif / Off / AV / Saiki / Munggah / Ngisor). Konfigurasi 7. 913703253309
PA6BPA-WW-L-SSA-AV-saiki Antumbra 6 Button NA Rampung putih (Aktif / Off / Sedheng / Low / AV / Saiki). Konfigurasi 8. 913703253409
PA6BPA-WW-L-SSA-2Z Antumbra 6 Button NA Rampung putih (On / Off / Master + Rong zona). Konfigurasi 9. 913703253509
PA6BPA-WW-L-SSA-3Z Antumbra 6 Button NA Rampung putih (Aktif/Mati/3 zona). Konfigurasi 10. 913703253609
PA2BPA-WW-L-SSA-onoff Antumbra 2 Button NA Rampung putih (Aktif/Mati). Konfigurasi 11-14. 913703253709
DINGUS-UI-RJ45-DUAL Cocog kanggo DACM - DyNet - 2 x soket RJ45, paket 10. Ora bisa digunakake karo DUS. 913703334609
DINGUS-DUS-RJ45-DUAL Cocok kanggo kisaran sensor DyNet DUS - 2 x Soket RJ45, paket 10. 913703064409

Siap nggunakake kekuwatan Dynalite
Dadi piranti jaringan sing bener, opsi kasebut ora ana watesan. Konfigurasi SSA bisa disesuaikan kanthi lengkap liwat piranti lunak System Builder kanggo nglayani syarat proyek sing luwih maju. Ngembangake karo piranti jaringan Dynalite liyane mbisakake jinis dimming liyane, integrasi BACnet, jadwal, ngawasi lan manajemen piranti lunak head-end, lan liya-liyane.

www.dynalite.com
© 2025 Signify Holding.

All rights reserved. Specifications are subject to change without notice. No r epresentation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem ar e registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their r espective owners.

Pitakonan sing Sering Ditakoni

Apa sistem bisa dikontrol saka jarak jauh?

Yes, the system can be integrated with a Building Management System over BACnet for remote control.

What is the maximum load supported by the system?

The system supports a 16 A lighting load and a 20 A general load.

Dokumen / Sumber Daya

PHILIPS DDC116-UL Solusi Kontrol Pencahayaan Arsitektur Sistem Tunggal [pdf] Pandhuan Instalasi
DDC116-UL, DUS360CR-DA-SSA, DUS804CS-UP-SSA, DDC116-UL Solusi Kontrol Pencahayaan Arsitektur Sistem Tunggal, DDC116-UL, Solusi Kontrol Pencahayaan Arsitektur Sistem Tunggal, Solusi Kontrol Pencahayaan Arsitektur, Solusi Kontrol Pencahayaan, Solusi Kontrol

Referensi

Ninggalake komentar

Alamat email sampeyan ora bakal diterbitake. Kolom sing dibutuhake ditandhani *