Intermatic Self-Adjusting Wall Switch Timer
Easy-Set Guide
This Easy-Set Instruction Sheet may be helpful in setting up common timer programs. Refer to the Installation and User Instructions Sheet for more information.
To Clear the Timer
- Press and hold down the ON/OFF button.
- Using a paper clip or pen, press and release the RESET button, which is to the lower right of the + button.
- Continue holding ON/OFF until you see INIT on the screen.
- Release ON/OFF.
- Wait until you see 12:00 am in MANual mode
Setting the Time and Date
- Press MODE to display SETUP.
- Press ON/OFF.
- Press + or – to set your hour for the current time of day.
- Press ON/OFF.
- Press + or – to set your minutes for the current time of day.
- Press ON/OFF.
- Press + to advance the year if needed.
- Press ON/OFF.
- Press + or – to change the month.
- Press ON/OFF.
- Press + or – to change the date.
- Press ON/OFF. Make sure it’s the correct day of the week. If not, go back and check the year.
- Press ON/OFF to choose DST (Daylight Saving Time)
- Press + to select Man if you do not observe DST, or
- Press + again to select Auto to automatically set for DST.
- Press ON/OFF to choose zone.
- Press + to select your zone. (Refer to map in the Install Sheet for proper zone).
- Press ON/OFF to review Dawn time.
- Press ON/OFF twice to review Dusk time.
- Press ON/OFF twice to save.
Programming Dusk ON/Dawn OFF
- Press MODE to display PGM.
- Press ON/OFF three times to choose DUSK.
- Press ON/OFF to choose the days you need, then press + to change days from ALL, M-F, WeeKenD, or individual day.
- Press ON/OFF to SAVE your work.
- Press + to go to Program 2.
- Press ON/OFF twice to display DAWN.
- Press ON/OFF to choose the days you need, then press + to change days from ALL, M-F, WeeKenD, or individual day.
- Press ON/OFF to SAVE your work.
- Press MODE to display AUTO.
Programming Dusk ON/Fixed Time OFF
- Press MODE to display PGM.
- Press ON/OFF three times to choose DUSK.
- Press ON/OFF to choose the days you need, then press + to change days from ALL, M-F, Weekend, or individual day.
- Press ON/OFF to SAVE your work.
- Press + to go to Program 2.
- Press ON/OFF twice to display DAWN.
- Press + until you get to 12:00 pm.
- Press ON/OFF.
- Press + or – to set the hour of the OFF time.
- Press ON/OFF
- Press + or – to set the minutes of the OFF time.
- Press ON/OFF to choose the days you need, then press + to change days from ALL, M-F, Weekend, or individual day.
- Press ON/OFF to SAVE your work.
- Press MODE to display AUTO.
Programming Fixed Time ON/Fixed Time OFF
- Press MODE to display PGM.
- Press ON/OFF button three times to choose DUSK.
- Press + to change it to 12:00 pm.
- Press ON/OFF.
- Press + or – to set the hour for the ON time.
- Press ON/OFF.
- Press + or – to set the minutes.
- Press ON/OFF to choose the days you need, then press + to change days from ALL, M-F, WeeKenD, or individual days.
- Press ON/OFF to SAVE your work.
- Press + to go to Program 2
- Press ON/OFF twice to display Dawn.
- Press + to change it to 12:00 pm.
- Press ON/OFF.
- Press + or – to set the hour for the OFF time.
- Press ON/OFF.
- Press + or – to set the minutes.
- Press ON/OFF to choose the days you need, then press + to change days from ALL, M-F, WeeKenD, or individual days.
- Press ON/OFF to SAVE your work.
- Press MODE button to display AUTO.
