Verizon FOIS Home Router User Manual

Verizon FOIS Home Router User Manual
Verizon FOIS Home Router User Manual

Model G3100

INTRODUCTION

1.0 Package Contents
1.1 System Requirements
1.2 Features
1.3 Getting to Know Your
Fios Home Router

The Verizon Fios Home Router lets you transmit and distribute digital entertainment and information to multiple devices in your home/office.


Your Fios Home Router supports networking using coaxial cables, Ethernet, or Wi-Fi, making it one of the most versatile and powerful routers available.

PACKA GE CONTENTS, SYSTEM REQUIREMENTS AND FEATURES

1.0/ PACKA GE CONTENTS
Your package contains:
• Fios Home Router
• Power adapter
• Ethernet cable, three meters (white)
• OSS (Open Source Software) insert guide

1.1/ SYSTEM REQUIREMENTS
System and software requirements are:
• A computer or other network device supporting Wi-Fi or wired Ethernet
• A web browser, such as Chrome™, Firefox®, Internet Explorer 8® or higher, or Safari® 5.1 or higher

1.2/ FEATURES
Your Fios Home Router features include:
• Support for multiple networking standards, including
–– WAN – Gigabit Ethernet and MoCA 1.1 interfaces
–– LAN – 802.11 b/g/n/ac/ax, Gigabit Ethernet and MoCA 2.5 interfaces
• Integrated wired networking with 4-port Ethernet switch and Coax (MoCA)

–– Ethernet supports speeds up to 1000 Mbps
–– MoCA 2.5 and 1.1 enabled to support speeds up to 700 Mbps over coaxial cable
• Integrated wireless networking with 802.11b/g/n/ac/ax access point featuring:
–– Enabled 802.11b capable speeds (based on device)
–– Enabled 802.11g capable speeds (based on device)
–– Enabled 802.11n capable speeds (based on device)
–– Enabled 802.11ac capable speeds (based on device)
–– Enabled 802.11ax capable speeds (based on device)
• Enterprise-level security, including:
–– Fully customizable firewall with Stateful Packet Inspection (SPI)
–– Content filtering with URL-keyword based filtering, parental controls, and customizable filtering policies per computer
–– Intrusion detection with Denial of Service protection against IP spoofing attacks, scanning attacks, IP fragment overlap exploit, ping of death, and fragmentation attacks
–– Event logging
–– MAC address filtering
–– Static NAT
–– Port forwarding
–– Port triggering

–– Access control
–– Advanced wireless protection featuring WPA2/WPA Mixed Mode and MAC address filtering
• Options, including:
–– DHCP server
–– WAN interface auto-detection
–– Dynamic DNS
–– DNS server
–– LAN IP and WAN IP address selection
–– MAC address cloning
–– IPv6 support
–– QoS support (end to end layer 2/3) featuring: Differentiated Services (Diffserv), 802.1p/q prioritization, and pass-through of WAN-side DSCPs, Per Hop Behaviors (PHBs), and
queuing to LAN-side devices
–– Remote management and secured remote management using HTTPS
–– Static routing
–– VPN (VPN pass through only)
–– IGMP
–– Daylight savings time support

1.3/ GETTING TO KNOW YOUR Fios Home Router
1.3a/ FRONT PANEL
The front panel’s unified button allows quick access to the Wi-Fi Protected Setup (WPS) feature and pairing mode.
The Router Status LED will be on white and solid when your router is turned on, connected to the internet, and functioning normally.

Router Status LED

FRONT PANEL
Router Status LED

The WPS button is used to initiate Wi-Fi Protected Setup. This is an easy way to add WPS capable devices to your wireless network. To activate the WPS function, press and hold the unified button located on the front of your Fios Home Router for more than two seconds. When WPS is initiated from your router, the Router Status
LED slowly flashes blue for up to two minutes, allowing time to complete the WPS pairing process on your wireless device (also known as a wireless client). When a device begins connecting to your router using WPS, the Router Status LED rapidly flashes blue for a few seconds, and turns solid blue and then solid white as the connection completes.
If there is an error during the WPS pairing process, the Router Status LED slowly flashes red for two minutes after the error occurs.
Refer to the “Connecting A Wi-Fi Device Using WPS” for more details. In addition, the unified button also provides a quick view of the operational state of the Fios Home Router using various colors as indicated in the chart above. Please refer to section 9.0h for details on the rear LEDs.

1.3b/ REAR PANEL
The rear panel of your router has a label that contains important information about your device, including the default settings for the router’s wireless network name (SSID), wireless password (WPA2 key), local URL for accessing the router’s administrative pages, and administrator password. The label also contains a QR code that you can scan with your smartphone, tablet, or other camera equipped Wi-Fi device to allow you to automatically connect your device to your Wi-Fi network without typing in a password (requires a QR code reading app with support for Wi-Fi QR codes).

The rear panel has seven ports; F-type coax, Ethernet LAN (four), Ethernet WAN, and USB. The rear panel also includes a DC power jack and a reset button.

Ethernet LAN – connects devices to your Fios Home Router using Ethernet cables to join the local area network (LAN). The four Ethernet LAN ports are 10/100/1000 Mbps auto-sensing and can be used with either straight-through or crossover Ethernet cables.
• USB – provides up to 1000 mA at 5 VDC for attached devices. For example, you could charge a cell phone. With a firmware upgrade, the USB host functionality may be available for other devices, such as external storage and cameras. Firmware updates are performed automatically by Verizon.
Ethernet WAN – connects your Fios Home Router to the internet using an Ethernet cable.
Coax WAN and LAN – connects your router to the internet and/ or to other MoCA devices using a coaxial cable.
Warning: The WAN coax port is intended for connection to Verizon Fios only. It must not be connected to any exterior or interior coaxial wires not designated for Verizon Fios.
Reset Button – allows you to reset your router to the factory default settings. To perform a soft reboot, press and hold the button for at least three seconds. To reset your router to the factory default settings, press and hold the button for at least ten seconds.
• Power – connects your Fios Home Router to an electrical wall outlet using the supplied power adapter.
Warning: The included power adapter is for home use only, supporting voltages from 105-125 voltage in AC. Do not use in environments with greater than 125 voltage in AC.

Questions about your Verizon FOIS Home Router User Manual? Post in the comments!
Download Verizon FOIS Home Router User Manual [PDF]

Sabbat X12 Bluetooth Headphones User Manual

Sabbat
Sabbat X12 Bluetooth Headphones

Instructions
Sabbat

Manufacture: Shenzhen Sabbat
Technology Development Co. LTD

Product Schematic Diagram

Product Schematic Diagram
Product Schematic Diagram

Package list
• Bluesooth headset ( 2PCS )
• Power storage room
• USB charging line
• Instruction
• Exquisite packaging
• Product qualification certificate

Wearing a Sketch

Wearing  a  Sketch

Product specification
• Name: Sabbat Music wireless Bluetooth headset
• Bluetooth name: Sabbat X12
• Version: 4.1+EDR
• Input: DC 5V
• Battery Capacity: 3.7V/60mAh
• Talking Time: About 2-3 Hours
• Charging Time): About 60 Min
• Rechargeable warehouse: 3.7V / 750mAh
• Profile Support: 115P/HFP/A2DP/AVACP
• Sensitivity: 120 ± 5dB
• Frequency Response: 20-20000Hz
• Impedance: 320

Products use
Bluetooth pairing

1. Press and hold the power button on the earphones for 5-10 seconds until red and blue lights flash at she same.
2. Double—click any headset (host) power button, red and blue lights alternately flash, waiting for the left and right headphones automatically pair.
3. The earphones connect successfully with your phone when only blue lights showing on the earphones.

Sabbat X12 wirless earphones charging instructions :
1. Firstly charge the charging cabin: connect the cabin with the power adapter through the charging cable that enclosed with the earphones. When the cabin is fully charged LED lights will stay red.
2. Secondly charge the earphones through cabin: put the earphones inside the cabin correctly, when the earphones are under charging both LED lights on the cabin and earphones will flash red. When the earphones are fully charged, LED lights on the earphones will tum blue and stay for 5 seconds and LED lights on the cabin will turn off 10 seconds later.

Bluetooth link Turn on the phones Bluetooth search scan to ” Sabbat X12 ” and click connect

  • The earphones will automatically connect with same phone the next time you turn on Bluetooth on the phone.
  • If you want to connect the earphones with another phone, please follow up the above steps.
Bluetooth Setting

1. Listen to the music
* When headphones boot and and mobile phone connection, can use mobile phones to listen to music.
* Press the open key in the process of music, music on hold. Press will continue to play the music again.
* Music played in the process, double click to open the key, will play the neat song music.

2. Call
* When the headphones on and connected to the phone, can answer the call. Pick up the phone and only one headset week.
* When calls, voice telephone number. click having calls prompt headphones for the key, can answer the phone, if long according to decline a cal
* Phone in the process, press the open key, will hang up the phone, to go back to the previous state.
*Phone in the process, the volume can be adjusted through the phone call.

3. OFF
* Long press the headset key 5 seconds, the LED display normally on a red light, then turn it off.
* When about headphones matching use, only need to due to nun it off with one of the headphones, another headset will automatically shut down.

Matters needing attention
1. The headset should be stored in a dry and ventilated environment, to avoid oil, water, steam, moisture and dust, such as contact, lest affect product performance.
2. Avoid using stimulus, organic solvents or items containing these ingredients, dean the headphones.
3. The use of headphones should be correctly according to the requirement specification, pay attention to use the influence of environment on the headphones. In order to ensure the smooth connection it is recommended that the distance between the phone and headset within 10 meters.
4. Connect the headphones have not or poor communications, and other problems, please do not remove the headset secretly ontology and its accessories, otherwise no warranty.
5. Recharge headphones, please choose the standard USB charging lite or the company specified in conformity with the requirements of charging cable.
6. To ensure that your normal use headphones, please make sure that the headset battery is enough.

Product Warranty Card

Warranty Description

Thank you for purchasing “Sabbat” brand products in order to ensure that the legitimate lights and interests of you, please be informed that to mad the following items:
• This card warranty certificate foe the product, the product need for maintenance, please be sure to provide this ..rd. together with the products our company after-sales.
• When this card is only effective use for warranty within the scope of the products, see below:
1. Through legal, formal channels for the company’s products,
2. The non-artificial damage products, including but not limited to remove secretly, improper use, manual disasters and other circumstances not within the scope of the warranty:
3. Does not exceed the product warranty:-
• Low considerations include and not limited to above.
• When the company reserves the final interpretation.

Questions about your Sabbat X12 Bluetooth Headphones User Manual? Post in the comments!

…….

Skytech Fireplace Remote User Manual

SKY-4001
INSTALLATION AND OPERATING INSTRUCTIONS

INTRODUCTION
SKYTECH’S remote control system was developed to provide a safe, reliable and user-friendly remote control system for gas heating appliances. Its battery operation allows the system to operate independently of household current. The system operates on radio frequencies with non- directional signals. The SYSTEM’s operating range is approximately 20 feet. The system operates on one of 255 security codes programmed at the factory

COMPONENTS
WARNING

THE SKYTECH SKY-4001 MUST BE INSTALLED EXACTLY AS OUTLINED IN THESE INSTRUCTIONS. FOLLOW INSTRUCTIONS CAREFULLY DURING INSTALLATION. ANY MODIFICATION OF THE SKYTECH SKY -4001 OR ANY OF ITS COMPONENTS WILL VOID THE WARRANTY AND MAY POSE A FIRE HAZARD.

TRANSMITTER

TRANSMITTER
TRANSMITTER

The transmitter operates on a 3v battery (included) made specifically for remote controls and electronic lighters. Before using the transmitter, remove the insulation tab
protecting one end of the battery in the battery compartment.

The transmitter has ON and OFF functions that are activated by pressing either button on the face of the transmitter. When a button on the transmitter is pressed, a signal light on the transmitter illuminates briefly to verify that a signal has been sent. Upon initial use, there may be a delay of five seconds before the remote receiver will respond to the transmitter. This is part of the system’s design. If the signal light does not illuminate, check the position of the transmitter’s battery

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important Note:

FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Questions about your Skytech Fireplace Remote User Manual? Post in the comments!

.

Peace Target Bluetooth Speaker User Manual 022-001

Manual for BT speaker

Small, compact size gives your audio powerful sound. The clear sound is powered by new generation amplifiers, that you can take with your enjoy anywhere.

FEATURES:
1.Portable speaker for your smart phone, tablet, laptop, or MP3 Player.
2.Light-weight, small in size, but incredible sound.
3.Plastic housing provides protection and great sound.
4.Up to 2-3 hours playback time, one a full charge

COMPONENTS INCLUDED
1.Mini speaker
2.Audio cable
3.Micro USB charging cable
4.User Manual

SPECIFICATIONS:
Power supplier: DC5V
Output power: 3W(1KHz,THD10%)
Frequency: 200Hz – 20KHZ
Signal&noise ratio:≥ 85dB
Impedance: 4 OHM(Ω)
Li-ion Output: 3.7V~4.2V+0.05V
Li-ion Input: 5V Lithium battery
capacity: 300mAh
Speaker Unit: 40mm

Button Description:

Long press for volume decrease

Long press for volume decrease; short press for last song.

answer / off the phone

Short press for pause or answer / off the phone.

Long press for volume increase; short press for next song.

Long press for volume increase; short press for next song.

Long press for switch on/off.

Long press for switch on/off.

hort press for radio /bluetooth play/line in model change

hort press for radio /bluetooth play/line in model change

hort press for radio /bluetooth play/line in model change

hort press for radio /bluetooth play/line in model change

Under BT Model:
Long press

hort press for radio /bluetooth play/line in model change

to turn on, at the same time, the blue light flashes. Search name of the speaker is “BT Speaker” Make your device and speaker bluetooth pairing. After a successful connection, light slow flash, sound will be issued “dong dong dong” tones

Under Line-in Model:

AUX audio playback: appendix provides the 3.5mm audio line.Can play music by link to mobile phone、MP3、MP4、PC、IPOD and other audio devices. Reminder: When it’s on AUX model, above buttons keeps on the same function.

Under radio Model:

Under radio Model

The interface description:

The interface description:

SAFETY CAUTIONS:

1.Please read the instructions carefully before using.
2.Avoid contact with liquids; keep away from water, and high moisture conditions.
3.Do not locate the speaker or cord near heat sources such as radiators, heaters, air ducts. or
direct sunlight.
4.Do not place a naked flame source such as candles on the Mini Speaker.
5.Recharge the battery with suitable voltage output(5V/500mA)
6.Do not hit the product severely, or insert any conductive objects into the speaker, or charging
jack.
7.Do not block the speaker grill when the speaker is running.
8.Stop using at once if high temperature, smoke, burning smell, nor-normal noise, or fire are
noticed coming from product.
9.Do not repair on your own, seek the help of a professional.
10.To avoid getting shocked, do not touch product with wet hands.
11.Keep out of reach of children.

TROUBLESHOOTING
No Sound
1.Audio cable is not fully plugged into the 3.5mm audio port on speaker or device.
2.Audio cable is damaged.
3.Source of audio is not working.
4.No LED indication when audio cable is plugged-in.
5.Mini speaker is out power.

Not charging:
1.Input power source is not normal(5V/500mA)
2.Micro USB adaptor of charging cable is not fully plugged into the mini speaker charging port.
3.Charging cable is damaged.

Questions about your Peace Target Bluetooth Speaker User Manual 022-001? Post in the comments!

Verdant Thermostat Manual V Model

Verdant V

V Series Thermostat
with an Occupancy Sensor

INSTALLATION MANUAL

Introduction
Verdant VX Series Energy Management Thermostats for the hospitality industry deliver unprecedented energy savings without compromising guest comfort.]


Integrated occupancy sensor uses a combination of motion and thermal sensing technologies for accurate occupancy detection. Reliable occupancy detection allows saving energy when rooms are unoccupied.


Energy saving presets eliminate the guesswork and make it easy to adjust the energy saving settings. (Patent Pending) Fully configurable energy saving settings allow customizing the thermostat energy saving settings to fit any situation.


Comprehensive configuration options ensure full compatibility with virtually any existing or emerging hospitality HVAC system with up to 2 heat and 1 cool stages.
Built-in wireless mesh-networking enables optional remote management

Before You Begin

Programming a Thermostat with a Network Programmer In case of Network Installation with Remote Management, the thermostat must be programmed with a Network Programmer specific to the property before the installation.

installation

Thermostat must not be powered during the programming procedure..
➤➤ Plug one programmer connector into the thermostat;
➤➤ Push the black button on the programmer. The red light on the
programmer should turn on and remain steadily lit;
If the red light on the programmer is blinking or is not steadily lit,
unplug the programmer from the thermostat and repeat the steps
above.
➤➤ Unplug the programmer from the thermostat;

Thermostat Installation
Mounting the thermostat to the wall
➤➤ Power of the HVAC unit;
➤➤ Remove the thermostat cover;
➤➤ Connect the thermostat wires to the supplied Wiring Harness – refer
to the Wiring Table to determine proper connections;
➤➤ Plug in the Wiring Harness into to the thermostat;
➤➤ Use the supplied wall anchors and mounting screws to secure the
thermostat to the wall;
➤➤ Follow the “Thermostat Configuration” instructions;
➤➤ Replace the thermostat cover and screw in the locking screw;
➤➤ Power on the HVAC unit.

Questions about your Verdant Thermostat Manual V Model? Post in the comments!
Download Manual [PDF]

Raycon Wireless Earbuds Manual RBE770

Raycon Wireless Earbuds

User Manual RBE770

MORE COMPATIBLE

Compatible with Apple IOS and Android Smartphones

Compatible with

EASY PAIRING AND CONNECTION

1. Quick Pairing

Long press the left and right earphones about 3 seconds to power on.
(till the blue lights flash).

Wait for left and right earphones to be paired automatically.
(the red and blue light of the right earphone flashes alternately, and
the light of the left earphone goes out)

Quick Pairing

Listen to voice prompts􀄟“Power on, set connected Left channel,
right channel pairing.Pairing success, set connected”,Left and right
earphones are successfully paired.

2. Pairing the Device Again

In the OFF state, press and hold the function keys of the left and right earphones for
about 8 seconds until the red and blue lights alternately flash (in the TWS mode at
the moment)

Wait for 3-5 seconds, the red and blue light of the right earphone flash alternately, and the light of the left earphone goes out, that is, both earphones are paired successfully.

Note: This product is paired by factory default way, you just need to long press
for 3 seconds until the blue light of both earphones flash to enter the pairing mode.
If due to some wrong operation, the left and right earphones are not synchronized,
or only one earphone has sound, then need to re-pair.


Note: If the left and right earphones are not interconnected within 1 minute, the
earphones will enter into the standby mode. If necessary, turn off the earphones
and repeat the above steps for re-connection.

3. Bluetooth Connection

Turn on Bluetooth of the cell phone, Search for the Bluetooth name: RAYCON RBE770, click it to connect.

Bluetooth Connection

DIVERSIFIED FUNCTIONS, ONE KEY TO CONTROL

DIVERSIFIED FUNCTIONS

CHARGING SCHEMATIC

Charging Capsule

When being charged: the red light flashes Fully charged: the red light long gleams Charging time: about 1 hour

Earphones

When being charged: the red light long gleams Fully charged: the red light goes out Charging duration: about 1 hour

Note: When charging the charging capsule, please use our standard charging data cable and 5V / 1A charger. Special note: Do not use fast charging charger above 5V / 1A which will damage the charging capsule!

CHARGING

Packing Details
Wireless earphones body (left and right)
Charging capsule
USB charging cable
User Manual
Exquisite packing
Carrying Pouch

WEARING SCHEMATIC

WEARING SCHEMATIC

Product Specifications

Product name: Raycon Wireless Earphones StarShip E70
Bluetooth connection name: RAYCON RBE770
Bluetooth version: 4.2
Power input: DC 5V
Battery capacity: 3.7V/60mAh
Call / playing duration: about 2-3 hours
Charging time: about 60 minutes
Battery capacity of the charging capsule: 3.7V / 750mAh
Support agreement: HSP/HFP/A2DP/AVRCP
Sensitivity: 120±5dB
Frequency response range: 20-20,000Hz
Impedance: 32

TROUBLE SHOOTINGS

The cell phone cannot find the wireless earphones.

  • Clear all the pairing data stored in the Bluetooth of the cell phone, and then restart the Bluetooth to search.
  • Restart the left and right earphones, and long press the multi-function keys of left and right earphones until the red and blue lights flash alternately, and activate Bluetooth pairing.
    Earphone delays or disconnects during the call or listening to music.
  • The wireless earphones are short of power.
  • The distance between the cell phone and the wireless earphone is more
    than 10 meters.
  • There is a large area of signal blocking objects between the cell phone and
    the wireless earphone, for example, the wall.
  • If the left and right earphones are not synchronized, please turn off the
    earphones and then turn on again to get paired and connected.
    Sound quality of the wireless earphone is not ideal.
  • The new earphones need a break-in process, the sound quality of each
    audio band will be enhanced after a period of time of use.

Questions about your Raycon Wireless Earbuds Manual RBE770? Post in the comments!
Download Raycon Wireless Earbuds Manual RBE770[PDF]

Blackweb Wireless Earphones Manual

Blackweb Wireless Earphones

TRUE WIRELESS STEREO EARPHONES
Model: BWD19AAH06, BW019.1-107


PRODUCT GUIDE

Product Information
1) Product Name TRUE WIRELESS STEREO EARPHONES
2) Model BWD19AAH06/BWD19AAH07
3) Speaker Rated Input Power 3mW
4) Speaker Maximum Input Power :5 mW
5) Speaker Diameter 5.8mm
6) Speaker Impedance 320
7) Sensitivity 89* 3dB
8) Charging Cable : 23cm

Package of Content

Package of Content

ON / OFF & Paring

ON / OFF & Paring

Questions about your Blackweb Wireless Earphones Manual? Post in the comments!
Download Blackweb Wireless Earphones Manual[PDF]

Tzumi Sound Mates Manual

Tzumi Sound Mates

TRUE WIRELESS EARBUDS

TWE paring

  1. Keep the distance between the device and the Bluetooth Earbuds within 3 feet(for pairing only)
  2. Press and hold the multi-function button on both earbuds for a few seconds until you hear prompt “ Power on”, and see blue lights flashing.
  3. You will hear prompt ”Left Channel” on Left Earbud and “ Right Channel” on Right Earbud to begin pairing.

Connect TWE to your device
Active the Bluetooth function on your device to search for “E41” and connect to it. You will hear ” Phone paired” from the Master Earbud(Right Earbud-Factory default setting), and blue lights flashing. It is ready for use.

NOTE:
Factory default setting is RIGHT Earbud as MASTER Earbud. To reset/change MASTER Earbud, hold multi-function button on BOTH earbuds for 6 seconds. When blue/red lights flash quickly, press multi-function button twice on the earbud you want to set as the MASTER Earbud.

POWER OFF
Option 1: Long press the Multi-function button for about 4 seconds, hear ”Power off”, the both earbuds will turn off.
Option 2: Put earbuds into charging case and it will be charged automatically. Both earbuds will turn off during charging.

HANDS FREE FUNCTION
Short press the multi-function button to answer an incoming call / end an ongoing call;
Long press the multi-function button to refuse an incoming call Double press the multi-function button to call the number that last called you

REMARK: the operation only support master earpiece.

SINGEL EARBUD PAIRING

  1. Press and hold the multi-function button for about 6 seconds, until you hear “ Power on” then “Pairing”, the blue/red lights flash quickly. (the other Earbud should be off during this process.)
  2. Active the Bluetooth function on your device to search the “E41” and connect to it.
  3. You will hear prompt” Phone paired” and blue lights flashing. It is ready for use.

Remark: If no device is connected within 5 minutes after power on, the Earbuds will automatically turn off to save power. After successful pairing, device will remember each other, it will be paired automatically next time.

CHARGING THE BLUETOOTH EARBUDS
Please fully charge before first use

To charge your earbuds: simply return them to the charging station, close the lid. They will charge automatically and the LED light will turn solid blue while charging. The LED light will turn off when charge is complete.
Charging time: around 1-1.5 hours
Play time: 2.5hours

CHARGE YOUR CHARGING STATION
Plug the provided micro USB charging cable into the bottom of the charging station. The LED light will turn solid red while charging. It will die out after full charged.
Charging time: 2 hours

PRODUCT’S SPECIFICATIONS
Bluetooth version: 4.2
Power output: 10mW
Speakers: D13mm
2 Frequency response: 20HZ-20KHZ Battery build-in earpiece: 45mAh2
Charging Station battery: 500mAh
Charging current: 50mA DC 5V

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.

Questions about your Manual ? Post in the comments!

Sabbat X12 Pro Manual

Sabbat X12 Pro
Sabbat X12 Pro

Sabbat X12 Pro Bluetooth Headset User Manual

Instructions

Sabbat

Manufacture:Shenzhen Sabbat Technology Development Co.,Ltd.

Product Schematic Diagram

Product Schematic Diagram
Product Schematic Diagram

Package list

• Bluetooth headset ( 2PCS ) Power Storage Room

• USS charging line

• Instruction

• Exquisite packaging

• Product qualification certificate

Wearing a Sketch

Wearing a Sketch
Wearing a Sketch

Product specification

• Name: Sabbat Music wireless Bluetooth headset

• Bluetooth name: Sabbat X12

• Version:4.1+EDR

• Input:DC 5V

• Battery Capacity:3.7V/60mAh

• Talking Time:About 2-3 Hours

• Charging Time):About 60 Min.

• Rechargeable warehouse: 3.7V/ 750mAh

• Profile Support:HSP/HFP/A2DP/AVRCP

• Sensitvity:120 ± 5dB

• Frequency Response:20-20000Hz

• Impedance:32 0

Products use Bluetooth pairing

1. Press and hold the power button on the earphones for 5-10 seconds until red and blue lights flash at the same.

2. Double—click any headset (host) power button, red and blue lights alternately flash, waiting for the left and right headphones automatically pair.

3. The earphones connect successfully with your phone when only blue lights showing on the earphones. Bluetooth link Turn on the phones Bluetooth search scan to ” SABBAT X12 ” and click connect

* The earphones will automatically connect with same phone the next time you turn on Bluetooth on the phone.

* If you want to connect the earphones with another phone, please follow up the above steps.

Setting
Setting

1. Listen to the music

* When headphones boot and and mobile phone connection, can use mobile phones to listen to music.

* Press the open key in the process of music, music on hold. Press will continue to play the music again.

* Music played in the process, double click to open the key, will play the neat song music.

2. Call

* When the headphones on and connected to the phone, can answer the call. Pick up the phone and only one headset work.

* When calls, voice telephone number.Click having calls prompt headphones for the key, can answer the phone, if long according to decline a call.

*Phone in the process, press the open key, will hang up the phone, to go back to the previous state.

*Phone in the process, the volume can be adjusted through the phone.

3. OFF

* Long press the headset key 5 seconds, the LED display normally on a red light, then turn it off.

* When about headphones snatching use, only need to du to win it off with one of the headphones, another headset will automatically shut down.

Sabbat X12 wireless earphones charging instructions :

1. Firstly charge the charging cabin: connect the cabin with the power adapter through the charging cable that enclosed with the earphones. When the cabin is fully charged LED lights will stay red.

2. Secondly charge the earphones through cabin: put the earphones inside the cabin correctly, when the earphones are under charging both LED lights on the cabin and earphones will flash red. When the earphones are fully charged, LED lights on the earphones will tum blue and stay for 5 seconds and LED lights on the cabin will turn of 10 seconds later.

Matter Needing Attentions

1. The headset should be stored M a dry and ventilated environment, to avoid oil, water, steam, moisture and dust, such as contact, lest affect product performance.

2. Avoid using stimulus, organic solvents or items containing these ingredients, dean the headphones.

3. The use of headphones should be correctly according to the requirement specification, pay attention to use the influence of environment on the headphones. In order to ensure the smooth connection, it is recommended that the distance between the phone and headset within 10 meters.

4. Connect the headphones have not or poor communications, and other problems, please do not remove the headset secretly ontology and its accessories, otherwise no warranty. 5. Recharge headphones, please choose the standard USB charging line or the company specified in conformity with the requirements of charging cable.

6. To ensure that your normal use headphones, please make sure that the headset battery is enough.

Warranty description

Thank you for purchasing am brand products in order to ensure that the legitimate rights and interests of you, please be informed that to read the following items: • This card warranty certificate for the product, the product need for maintenance, please be sure to provide this card together with the products our company after-sales. • When this card is only effective use for warranty within the scope of the products, see below:

1. Through legal, formal channels for the company’s products;

2. The non-artificial damage products, including but not limited to remove secretly, improper use, natural disasters and other circumstances not within the scope of the warranty;

3. Does not exceed the product warranty;

• Low considerations include and not limited to above.

• When the company reserves the final interpretation.

Warranty Card
Warranty Card

FCC Caution.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Questions about your Sabbat X12 Pro Manual ? Post in the comments!

Haylou GT1 TWS BT Earphones Manual

Haylou

Haylou-GT1 TWS BT Earphones Manual

Haylou Logo

Overview
Charging Case

Charging Case

What’s in the Box
BT earphones, Charging case, EarTips × 2 pairs, Manual, Charging cable.

Earphones
Earphones

Medium Ea r T i p s h ave been assembled in advance. However, you may try large or small ones, if the medium ones do not fit you well.

keep Mic Outside

When calling, adjust Mic towards mouth to gain clear calling.

Power-on
Take out earphones from the case to power on them. Or touch both panels for 1.5s to power on earphones (LED glows solid white) when they are not in the case.

Power-on

Power-off
Put earphones into the case to power off them. Or touch both panels for 4.5s to power off earphones. (LED glows solid red for 2s).

Power-off

Ignore Call
Touch the panel for 1s to ignore incoming call.

Ignore Call

Stereo Mode
Auto pairing: take out both EarBuds from the case and they will auto pair with each other in 2 or 3s. Earphones will be connectable to cellphone when white slowly. On cellphone, LED on right EarBud blinks search for “Haylou-GT1_R” and tap to connect. If earphones fail to be connected to cellphone, please put EarBuds back to the case and repeat the above steps. Earphones will auto reconnect to the last device in connectivity records, if any.

Note: earphones have been setted to factory when shipping out.

Stereo Mode

Manual pairing: manually power on two EarBuds and they will auto pair with each other when LED blinks white promptly. Then LED on the right EarBud will blink white slowly and now you can tap it on cellphone to connect.

Mono Mode
Auto pairing: take out one EarBud from the case to power on it. Its LED will soon blink slowly then search for Haylou-GT1 R/L on cellphone and tap to connect. EarBud will auto reconnect to last device in connectivity records, if any.

Note: it may take more times for the left EarBud to reconnect

Manual pairing: manually power on one EarBud. Its LED will soon blink white slowly then search for it on cellphone and tap to connect

How to Charge
Prior to using, please peel off sticker on the pogo pins and top up the earphones.

How to Charge

Play/pause
When standby, touch the panel to pause/play music.
Note: media player should run in background.

Play-pause

Voice Assistant
When standby, triple touch the panel to activate voice assistant.
Note: device needs to support voice assistant and fast awakening be turned on.

Voice Assistant

Answer/End Call
Double touch the panel to answer incoming call and double touch the panel again to end it.

Answer-End Call

Skip Track Forward/backward
Touch the panel on right earbud twice to skip track forward.
Touch the panel on left earbud twice to skip track backward.

Three-way Calling & Switch
Touch the panel twice to answer incoming call from phone. if another call is coming in sync , touch the panel to put the first call on hold while activating the second one. Double touch the panel to switch between active call and held call.

Switch Audio Output
When calling, touch the panel for 1s to switch audio output between earphones and cellphone.

Factory Setting
If earphones do not function well, please refer the following steps to reset factory: take EarBuds out from the case. Power off the earphones then toch both panels for about 15s ( LED will blink red and white three times twice). After that, put them back to the case. Delete connectivity record on cellphone before processing another pairing. (All connectivity records relating to the EarBuds will all be removed).

Basic Parameters
Operation range: 10m(with no obstacle)
Battery capacity: 43mAh(single EarBud)
Changing time: approx. 1.5hr
Calling time: approx. 3.5hr
Standby time: approx. 150hr
Input parameter: 5V 100mA
Battery type: li-ion
Wireless connection: BT 5.0
Charging case
Input parameter:5V 500mA
Output parameter:5V 150mA
Charging time: approx. 2hr
Standby time: approx. 4 months
Battery capacity: 310mAh
Battery type: li-ion

Caveats
1. Never disassemble or modify your headset for any
reasons to avoid any damages and danger.
2. Do not store the headset in extreme temperatures
(under 0℃ or over 45℃).
3. Avoid using the indicator close to the eyes of
children or animals.
4. Do not use this headset during a thunderstorm to avoid
irregular function and increased risk of electricshock.
5. Do not use harsh chemicals or strong detergents to
clean the headset.
6. Keep the headset dry.

Warranty Card
Warranty Period
12 months after the next day receiving this item. Free exchange service will not be accessed under
following circumstances:
1. Damages caused unauthorized disassembly.
2. Defects or physical damages caused by leaking or dropping off.
3. Damages by act of God.Supposing your item is within any damages or defects except the above circum stances, please return to us or your distributor for free repairing.

Tips
1. Before using the headset, please read the manual carefully and keep it for future references.
2. The headset need to be fully charged prior to first-time use.
3. If the headset is left unused for over two weeks, please recharge it periodically.
4. Please use the chargers made by qualified manufacturer.
5. If the headset cannot be found by your phone, please check whether it is in pairing mode; if left unconnected for a long while, the headset will exit pairing mode, please re-enter the mode; if a procedure error of your phone occurs, reboot it; if a procedure error of the headsetoccurs, reboot or reset it.

Address: Suite 1303, 1305 and 1306, 13/F, Project Phrase
2 of Gaosheng Tech Tower, Gaosheng Tech Park,
No.5 Longxi Road, Zhouxi Community, Nancheng
District, Dongguan City, Guangdong, China.
Manufacturer: Dongguan Liesheng Electronic Co., Ltd.
Web: www.haylou.com
Perform standard: Q/LS 1-2018
Made In China

Hazardous substances and their contents in the item
Hazardous Substances

WEEE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

Questions about your Haylou GT1 TWS BT Earphones Manual ? Post in the comments!
Haylou GT1 TWS BT Earphones Manual [PDF]