iBoard-LOGO

iBoard IB-231C&H Running Boards Side Bars Side Steps Step Bars

iBoard-IB-231C&H-Running-Boards-Side-Bars-Side-Steps-Step-Bars-PRODUCT

Product Usage Instructions

  • Start from the driver-side front of the vehicle.
  • Partially attach the Driver Front Mounting Bracket (DFM) using (2) M8X1.25-30mm Hex Bolts, (2) M8 Lock Washers, and (2) M8 Large Flat Washers.
  • Do not fully tighten the hardware.
  • Move to the center of the vehicle.
  • Partially install the Driver Center Mounting Bracket (DCM) using the provided hardware.
  • Do not fully tighten at this time.
  • Move to the vehicle’s rear and repeat Step 1 to install the Driver Rear Mounting Bracket (DRM).
  • Do not fully tighten the hardware.
  • Attach the Step Bar to the mounting brackets using the provided hardware.
  • Ensure all bolts are securely tightened.
  • Perform periodic inspections to ensure all hardware is secure.

Note: Use mild soap or non-abrasive products for cleaning to protect your bars/boards. FAQ

  • Q: Is drilling required for installation?
  • A: No, drilling is not required for installing this product. It features a rocker panel mount design.
  • Q: What should I do if I encounter missing parts?
  • A: Before starting installation, ensure all parts are present as listed in the manual. If any parts are missing, contact customer support at info@iboardauto.com.
  • Q: How often should I inspect the installation?
  • A: Periodic inspections should be done to ensure all hardware is secure and tight. Check the installation regularly to maintain safety.

PART#: IB-231C&H

Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 X
8mm 16-18
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X

READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM THE BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.

  • ROCKER PANEL MOUNT
  • NO DRILLING REQUIRED

PART LIST

iBoard-IB-231C&H-Running-Boards-Side-Bars-Side-Steps-Step-Bars-FIG-1

Hardware Package

Hardware Package A (For Bracket Installation)
Item QTY Description Item QTY Description
1# 12 M8X1.25-30mm Hex Bolts 3# 12 M8 Lock Washers
2# 12 M8 Large Flat Washers
iBoard-IB-231C&H-Running-Boards-Side-Bars-Side-Steps-Step-Bars-FIG-2
Hardware Package B (For Stainless Steel Step Bar Installation)
Item QTY Description Item QTY Description
1# 12 M8X1.25-35mm Carriage Bolts 3# 12 M8 Nylon Lock Nuts
2# 12 M8 Large Flat Washers 4# 6 Sliders (Packed with Step Bars)
iBoard-IB-231C&H-Running-Boards-Side-Bars-Side-Steps-Step-Bars-FIG-3

Installation Instructions

STEP 1

  • Start installation from the driver-side front of the vehicle.
  • Locate the (2) factory threaded holes in the side panel by the front flare in the body.
  • Partially attach the Driver Front Mounting Bracket (DFM) to the vehicle using the included (2) M8X1.25-30mm Hex Bolts, (2) M8 Lock Washers, and (2) M8 Large Flat Wash-ers (Fig 1).
  • Do not fully tighten the hardware at this time.

iBoard-IB-231C&H-Running-Boards-Side-Bars-Side-Steps-Step-Bars-FIG-4

STEP 2

  • Move to the center of the vehicle. There are (2) sets of holes in the side panel between the installed Mounting Brackets, one set by the front Mounting Bracket and the other by the rear Bracket.
  • To determine which holes you will be using.
  • Partially install the Driver Center Mounting Bracket (DCM) to the vehicle using the included (2) M8X1.25-30mm Hex Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers (Fig 2). Do not fully tighten the hardware at this time.

iBoard-IB-231C&H-Running-Boards-Side-Bars-Side-Steps-Step-Bars-FIG-5

STEP 3

  • Move to the rear of the vehicle. Repeat Step 1 for Driver Rear Mounting Bracket (DRM) installation, (Fig 3). Do not fully tighten hardware at this time.

iBoard-IB-231C&H-Running-Boards-Side-Bars-Side-Steps-Step-Bars-FIG-6

STEP 4
Once all (3) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 4 & 5)

  1. Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
  2. Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
  3. Slide the Slider (with carriage bolts) to the Step Bar.
  4. Repeat to install the other (2) sliders to the step bar.
  5. Attach the Step Bar (with the Sliders) to the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 5). Do not fully tighten the hardware at this time.

Note: The Sliders are packed with the Step Bars.
Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-4 for the other side Step Bar installation. The installation is completed!iBoard-IB-231C&H-Running-Boards-Side-Bars-Side-Steps-Step-Bars-FIG-7

Attention

  • Do periodic inspections of the installation to make sure that all hardware is secure and tight.
  • To protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.

CONTACT

iBoard-IB-231C&H-Running-Boards-Side-Bars-Side-Steps-Step-Bars-FIG-8

Documents / Resources

iBoard IB-231C&H Running Boards Side Bars Side Steps Step Bars [pdf] Installation Guide
IB-231C H Running Boards Side Bars Side Steps Step Bars, IB-231C H, Running Boards Side Bars Side Steps Step Bars, Bars Side Steps Step Bars, Steps Step Bars, Step Bars, Bars

References

Leave a comment

Your email address will not be published. Required fields are marked *