Installation Diagram

Ib txwm txiav lub hwj chim ua ntej txhim kho lossis hloov lub teeb thiab ua ntej ntxuav lossis lwm yam kev tu.

1. Tshem tawm fixture los ntawm nws thawj pob.
2. Separate mounting plate (1c) from canopy removing canopy screws (2f)
3. Attach mounting plate (1c) to electrical junction box (la) using screws provided (1d) in hardware package
4. Txhawm rau hloov kho qhov siab, thawb thiab tuav cov hlau gripper (2g), xaim xaim mus rau qhov ntev uas xav tau thiab tom qab ntawd tso cov hlau gripper (2g) kom ruaj ntseg (Tshem tawm ntau tshaj yog tias tsim nyog)
5. Secure mounting plate (1c) to mounting surface with anchors (1f) and screws (1e)
6. Ua kom muaj kev sib txuas hluav taws xob zoo (dub rau kub "L", dawb rau nruab nrab "N", hauv av rau "GND") nrog cov txiv ntseej (1b) muab rau hauv pob khoom kho vajtse
7. Attach canopy(2a) to mounting plate(1c) with canopy screws(2f) and nuts(2c) , tighten them(2f and 2c).
8. Fine tone hlau ntev yog tias tsim nyog, los ntawm thawb thiab tuav hlau gripper (2g) thiab tom qab ntawd kho cov xaim kom ntev

1. To shorten the cable-just push the cable up, cable will be locked Automatically.
2. To length the cable-lift up on the cable and push up on the lock while keep the lock depressed, lower the cable to the desired length, release the lock to set.

A: thawb

LED Wireless chaw taws teeb tswj cov lus qhia ua haujlwm

I. Key function of remote control

1. qhov taw qhia teeb
2. Qhib
3. brightness +
4. lub teeb txias
5. lub voj voog
6. Tua tawm
7. brightness -
8. lub teeb sov
9. hmo ntuj

II. Key instructions

Qhib: Lub sijhawm luv lamp lighting, Electricity within 5 s, Long press for the code function, After power on 5 s, Long press has no effect

Tig: Lub sijhawm luv lamp goes out, Electricity within 5s, Long press for clear code function, After power on 5 s, Long press has no effect;

Lub caij ntuj sov: +

1, Short on time, Turn the cold light fixture on one level, At the same time, the warm light lamp darkens one level, There are 15 levels of cold light from out to full light;
2, Long time, The luminaire is gradually lightened, At the same time, the warm light gradually darkens;

Lub teeb sov: +

1, Short on time, The warm light fixture should be one step brighter, When the cold light lamp darkens ib theem, Muaj 15 theem ntawm lub teeb sov los ntawm tawm mus rau tag nrho lub teeb;
2, Long time, The warm luminaire is gradually lightened, At the same time, the cold light gradually darkened;

brightness + :

1, Short on time, Heat and cold light lamps are brighter, There are 11 levels of brightness from lowest to highest;
2, Long time, Cold and warm light lamps and lanterns are gradually brightened;

brightness – :

1, Short on time, Dim the light and cold lamps, Muaj 11 theem ntawm qhov ci ntawm qhov siab tshaj mus rau qis tshaj;
2, Long time, The cold and warm light lamps are gradually dimmed; cycle: Short press the loop key, The light is Warm, neutral, cold, Nightlight, Four state cycles, Press short to change the state one at a time; night lamp: Luv nias lub teeb hmo ntuj, Qhov qis tshaj qhov ci ntawm alamp converted to Warm light;

The key light : Key indicator light, The indicator button is pressed;

Lus Cim: Ib qho ntawm cov cua sov thiab cua txias teeb chaw, Cov neeg siv khoom tuaj yeem txhais lawv tus kheej raws li cov khoom siv hluav taws xob thiab lamps.

III. Functional specifications

Daim ntawv qhia ua haujlwm

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 vib nas this. Long press the light button once, LED light flashes slowly once. The code successfully. Then the remote control can control the brightness, cooling and heating of the LED lights with good code.
Note: An LED light is only controlled by the last successful remote control, For example, If an LED 1 ight fixture, There is a new remote control and its code matching is successful, Then the remote control will automatically clear the code with the lamp. But a remote control can be coded and controlled with multiple LED lights,

Code clearing muaj nuj nqi

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 vib nas this, Long press the Turn off button or nightlight button once, LED light slow flash 2 time, The Ming and Qing dynasties were successful.

Note: The function of code clearing is based on the code matching between the remote control and the lamp, rau example, hauv qab no, cov chaw taws teeb tswj thiab lamp do not have the function of code clearing, If there is no clear code function, A long press to turn off the light has no effect.
(1) The remote control is not coded with the lamp, Then there is no clear code function.
(2) When they had finished coding, they cleared the code, Then there is no clear code function.
(3) They have coded each other, But then came a new remote control that corresponded with the light fixture, Then the remote control and its code function will automatically clear, No clear code function.

1. On switch function,

Cov lamp is normally energized, Power on the 0.5S-2S switch, The light is Warm, neutral, cold, Nightlight, 4 state loop Twitches.

2. Fais fab kev nco muaj nuj nqi

Siv cov chaw taws teeb tswj los kho qhov ci ntawm LED teeb, Lub ci ci ntawm LED lamps thiab tus lej code tus nqi ntawm cov chaw taws teeb tswj yuav khaws cia hauv lub cim xeeb ntawm LED maub los tom qab 15S ntawm lub zog, Lub zog rov qab rau tom qab koj tau poob lub zog thiab teeb lub lamp at its previous brightness, And has the code remote control is still controllable.

Cov ntaub ntawv / Cov ntaub ntawv

Digilog E27 LED Wireless Chaw taws teeb tswj lub teeb Fixture [ua pdf] Daim ntawv qhia kev teeb tsa E27 LED Wireless Chaw taws teeb tswj lub teeb Fixture, E27, LED Wireless Chaw taws teeb tswj lub teeb Fixture, Chaw taws teeb tswj lub teeb Fixture, Lub teeb Fixture, Fixture

Cov ntaub ntawv

• Cov neeg siv phau ntawv