Kiʻi hoʻokomo

E hoʻokaʻawale mau i ka mana ma mua o ka hoʻokomo ʻana a i ʻole ka hoʻololi ʻana i ka puʻupuʻu a ma mua o ka hoʻomaʻemaʻe ʻana a i ʻole ka mālama ʻana.

1. Wehe i ka mea paʻa mai kona pūʻolo kumu.
2. Separate mounting plate (1c) from canopy removing canopy screws (2f)
3. Attach mounting plate (1c) to electrical junction box (la) using screws provided (1d) in hardware package
4. No ka hoʻololi ʻana i ke kiʻekiʻe o ka mea paʻa, paʻi a paʻa i ka uea gripper (2g), hoʻoheheʻe i ka uea i ka lōʻihi i makemake ʻia a laila hoʻokuʻu i ka grip uea (2g) e hoʻopaʻa (Wehe i ka uea keu inā pono)
5. Hoʻopaʻa paʻa i ka pā kau (1c) i ka ʻili o ke kau ʻana me nā heleuma (1f) a me nā wili (1e)
6. E hana i nā pili uila kūpono (ʻeleʻele i ka wela "L", keʻokeʻo i ke kū ʻole "N", lepo i "GND") me nā nati uea (1b) i hāʻawi ʻia i loko o ka pūʻolo lako.
7. Attach canopy(2a) to mounting plate(1c) with canopy screws(2f) and nuts(2c) , tighten them(2f and 2c).
8. ʻO ka lōʻihi o ka uea leo maikaʻi inā pono, ma ke kaomi ʻana a paʻa i ka uea gripper (2g) a laila hoʻololi i ka uea i ka lōʻihi i makemake ʻia.

1. To shorten the cable-just push the cable up, cable will be locked Automatically.
2. To length the cable-lift up on the cable and push up on the lock while keep the lock depressed, lower the cable to the desired length, release the lock to set.

A: paʻi

ʻO nā ʻōlelo aʻoaʻo hana hoʻokele uila uila uila

I. Key function of remote control

1. kukui kuhikuhi
2. Hōʻā
3. ʻōlinolino +
4. kukui anu
5. pōʻaiapuni
6. Hoʻopio
7. ʻōlinolino –
8. kukui mahana
9. kukui pō

II. Key instructions

E ho'ā: Wā pōkole lamp lighting, Electricity within 5 s, Long press for the code function, After power on 5 s, Long press has no effect

Hoʻopau: manawa pōkole lamp hele i waho, Uila i loko o 5s, Paʻi lōʻihi no ka hana code maopopo, Ma hope o ka mana ma 5 s, ʻAʻohe hopena lōʻihi;

Ke kukui anu +:

1, Short on time, Turn the cold light fixture on one level, At the same time, the warm light lamp darkens one level, There are 15 levels of cold light from out to full light;
2, Long time, The luminaire is gradually lightened, At the same time, the warm light gradually darkens;

Ke kukui mahana +:

1, Short on time, The warm light fixture should be one step brighter, When the cold light lamp pōʻeleʻele hoʻokahi pae, He 15 pae o ka malamalama mehana mai waho a i ka malamalama piha;
2, Long time, The warm luminaire is gradually lightened, At the same time, the cold light gradually darkened;

brightness + :

1, Short on time, Heat and cold light lamps are brighter, There are 11 levels of brightness from lowest to highest;
2, Long time, Cold and warm light lamps and lanterns are gradually brightened;

brightness – :

1, Short on time, Dim the light and cold lamps, He 11 pae o ka olinolino mai ke kiekie a ka haahaa;
2, Long time, The cold and warm light lamps are gradually dimmed; cycle: Short press the loop key, The light is Warm, neutral, cold, Nightlight, Four state cycles, Press short to change the state one at a time; night lamp: E kaomi pokole i ke pihi kukui po, Ka malamalama haahaa o alamp hoʻololi ʻia i ke kukui Pumehana;

The key light : Key indicator light, The indicator button is pressed;

'Ōlelo Aʻo: Kekahi o ka wela a me ka hooluolu malamalama Settings, Customers hiki ke hoakaka ia lakou iho e like me ka mana lako a me ka lamps.

III. Functional specifications

Hana palapala ʻāina

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 kekona. Long press the light button once, LED light flashes slowly once. The code successfully. Then the remote control can control the brightness, cooling and heating of the LED lights with good code.
Note: An LED light is only controlled by the last successful remote control, For example, If an LED 1 ight fixture, There is a new remote control and its code matching is successful, Then the remote control will automatically clear the code with the lamp. Akā hiki ke hoʻopaʻa ʻia a mālama ʻia kahi mana mamao me nā kukui LED he nui,

Hana hoʻomaʻemaʻe code

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 kekona, Long press the Turn off button or nightlight button once, LED light slow flash 2 time, The Ming and Qing dynasties were successful.

Hoʻomaopopo: Hoʻokumu ʻia ka hana o ka hoʻomaʻemaʻe code ma ke code hoʻohālikelike ma waena o ka mana mamao a me ka lamp, No ka example, ma keia mau hihia, o ka mana mamao a me ka lamp ʻAʻole i loaʻa ka hana o ka hoʻomaʻemaʻe code, Inā ʻaʻohe hana code maʻemaʻe, ʻaʻohe hopena o kahi paʻi lōʻihi e hoʻopau i ke kukui.
(1) The remote control is not coded with the lamp, A laila ʻaʻohe hana code maopopo.
(2) When they had finished coding, they cleared the code, Then there is no clear code function.
(3) They have coded each other, But then came a new remote control that corresponded with the light fixture, Then the remote control and its code function will automatically clear, No clear code function.

1. On switch function,

ʻO ka lamp is normally energized, Power on the 0.5S-2S switch, The light is Warm, neutral, cold, Nightlight, 4 state loop Twitches.

2. Hoʻopau i ka hana hoʻomanaʻo

E hoʻohana i ka mana mamao e hoʻoponopono i ka ʻōlinolino o nā kukui LED, ʻO ke kukui o LED lamps a e mālama ʻia ka waiwai code o ka mana mamao i ka hoʻomanaʻo o ka mana LED ma hope o 15S o ka mana, Hoʻi hou ka mana ma hope o kou nalowale ʻana i ka mana a hoʻomālamalama i ka l.amp i kona 'ōlinolino mua, A loaʻa i ke code mamao mana e mau controllable.

Palapala / Punawai

ʻO Digilog E27 LED Wireless Remote Control Light [pdf] Alakaʻi hoʻokomo E27 E27 LED Uku Uku Uku Kukui, EXNUMX.

Nā kuhikuhi

• Palapala Hoʻohana