HDWR Global AC600 RFID Access Control Reader

Specifications

• Warranty: 1 year
• Product type: RFID card, password and fingerprint access control reader
• Material: metal
• Processor: 32-bit microprocessor with ARM core
• Operating frequency: 125 kHz
• Max number of employees in the database: 10,000
• Max. number of fingerprints in the database: 600
• Supported RFID cards: EM
• Verification Type: RFID Card, Password, Fingerprint
• Access control: yes
• Interface: Wiegand 26/34
• Working Voltage: DC 12-24V
• Operating Current: ≤100mA
• Standby Current: ≤35mA
• Ingress Protection: IP68
• Keyboard and keys: touch keyboard
• Operating Temperature: 0%~95%
• Operating Humidity: 5 to 95%
• Product dimensions: 13.9 x 5.6 x 2 cm
• Package dimensions: 19.3 x 12.6 x 6 cm
• Product weight: 500 g
• Product weight with packaging: 900 g

Set contents

• RFID Access Control System
• Screws and mounting pins
• Allen key
• Manual

Features

• The access control reader offers user verification through an RFID card, individual password and fingerprint
• Ability to set a single verification method or a combination of several methods
• IP68 rating ensures water resistance, so the device can be installed outdoors
• The maximum capacity of users in the database is as much as 10,000, which makes the reader ideal equipment for large companies
• 126 kHz operating frequency and Wiegand 26 and Wiegand 34 interface
• Possibility to connect the reader with a time and attendance recorder, electronic and electromagnetic door lock, intercom, videophone and other external devices with DC 12-24V voltage

Introduction

The product in this series is a new generation of multifunctional autonomous access control. It uses a 32-bit microprocessor with an ARM core, which is efficient, stable and reliable. It includes reader mode and stand-alone access control mode, etc. Widely used in various situations, such as offices, residential communities, villas, banks, etc.

Installation

• Remove the back cover of the device using the special screwdriver provided.
• Drill 2 holes in the wall for self-tapping screws and 1 hole for wire.
• Insert the provided rubber plugs into the two holes.
• Secure the back cover to the wall using 2 self-tapping screws.
• Pull the cable through the cord hole.
• Attach the keyboard to the back cover. (See figure below.)

Wiring Diagram

Drawing Connection Diagram

1. Shared power supply
2. Special power supply
3. Reader Mode

Sound and light signalling

Operation status	Light signal	Beep
Ready for action	Red
Operation successful	Green	One longer beep
Operation failed		Three short signals
Starting the programming mode via the administrator tab		Two short signals
Disabling Programming Mode via Admin Tab		One longer beep
Pressing the number button		One short beep
Press the * button		One long beep
Enter your access code	Red LED flashes slowly
Card reading in card plus code mode	Red LED flashes slowly
Multi-user card reading	Red LED flashes slowly
Entering Programming Mode	Red LED flashes slowly
Enable Settings Status	Orange
Unlock	Green
Audible alarm	The red LED flashes quickly	Alarm

Admin Menu – Standalone Mode Settings

Device Management

Entering Programming Mode	Menu	Stages of action	Description	Default
	00	New admin code # new admin code #	Change the admin code	999999
	01	Card	Add an
		reading/fingerprint	admin card
		input	or fingerprint
		twice*
	02	Card	Remove an
Press * Admin Code# (By default, the		reading/fingerprint input twice*	admin card or fingerprint
		0#	Reader Mode
admin code is “999999”)	03
		1#	Self- contained access control mode	1
		2#	Switching
			relay mode
	08		WIFI Matching	Optional
	09	Unlock code # (4-	Access code
		6 digits)

Add and remove users

Advanced settings

Entering ProgrammingMode	Menu	Stages of action	Description	Default
Press *Admin Code# (By default, the admin code is„999999”)	41	(0-300) #	Door open time range: 0-300s,0 equals50ms	5
	42	0 #	Alarm time setting, 0s means noalarm	0
		(1-99) #	Alarm Time Range: 1-99min
	61	0#	Normal OperatingMode	0
		1#	External alarm and built-in buzzerwill work if incorrect operations are repeated 5times.

Reader mode settings

Entering ProgrammingMode	Menu	Stages of action	Description	Default
Press *Admin Code # (By default, the admin code is “999999”)	00	New AdminCode #	Change theadmin code	999999
	01	Card reading/ double inputFingerprint*	Add an administrator card orfingerprint
	02	Card reading/ double inputFingerprint*	Remove an administrator card orfingerprint
	03	0#	Reader Mode	1
		1#	Stand-alone accesscontrol mode
		2#	Switchingrelay mode
	11	Enter your fingerprinttwice…*	Adding user fingerprintscontinuously	“…”means to repeat the previous operation, Press * to exit. to exit.
		Enter the ID number # Enter your fingerprinttwice…*	Add user fingerprints by specific ID number
	21	Enter your fingerprint once…* Enter the secondfingerprint…*	Removing user fingerprints continuously
		Tap ID number #… *	Delete users by a specificID number
	20	0000#	Delete allusers

	42	0#	Alarm time setting, 0s means noalarm	0
		(1-99) #	Alarm Time Range: 1-99min
	51	(0-255) #	Set the devicenumber	0
	52	(26-58) #	Wiegand Output:26-58bits	26
	53	0#	Keyboard transmissionformat 4 bits	0
		1#	8-bit keyboard transmission format
		2#	Virtual card output number

Admin card support
Read added admin card -> Read first user card -> Read second user card -> … -> Read admin card again

Note: The add tab is used to add tab users continuously and quickly. When reading the card for the first time, you will hear a short beep twice and the LED will illuminate orange. This means that user addition programming has been introduced.
When you read the administrator card again, you will hear a long, single beep and the LED will turn red. This means you exit the user addition program.

Delete a card
Read Delete Admin Card -> Read First User Tab -> Read Second User Tab -> … -> Read Admin Tab Again

Note: The Delete Card feature is used to continuously and quickly delete user cards. When reading the administrator card, you will hear a short beep twice and the LED will light up amber, indicating that the user has been removed.
When you read the administrator card again, you will hear a long, single beep and the LED will turn red, indicating that you are out of the user delete settings program.

User support

1. Change your user code with a card
   Press * -> read card -> enter old code # -> enter new code # -> re-enter new code #
   Remark. The default code “1234” of the matching card cannot open the door unless you change the other codes.
2. Changing the user passcode with your fingerprint
   Press * -> Enter fingerprint -> Enter old code # -> Enter new code # -> re-enter new code #
   Remark. The default “1234” code of the matching fingerprint cannot open the door without changing other codes.
3. Changing the user code with the ID number
   Press * -> enter ID number # -> enter old code # -> enter new code # -> re-enter new code #
   Remark. The ID number must be known to the administrator before changing the code, the user code cannot be the default code “1234”.

Other operations

1. Alarm Off
   Read admin card or read valid user card or enter fingerprint or type admin code # Remark. When the alarm is activated, the user can turn off the alarm by reading the registered card or entering the registered fingerprint or administrator code.
2. Factory reset
   Users can restore the factory default settings if they forget the admin code or modify the default settings.
   To restore the device to factory settings, turn off the power, press and hold the # button or the exit button continuously, turn on the power, release the # button or the exit button until you hear a double beep. The admin code will be reset to the default code, which is 999999.
   Remark. Registered user data will not be deleted after a factory reset.

FAQ

• Q: How do I add a new admin code?
  A: In Standalone Mode Settings, enter # followed by the new admin code.
• Q: How can I add or remove card users?
  A: While in Programming Mode, follow the instructions to add or remove card users as outlined in the manual.
• Q: What is the default admin code?
  A: The default admin code is 999999.

Documents / Resources

HDWR Global AC600 RFID Access Control Reader [pdf] User Manual AC600 RFID Access Control Reader, AC600, RFID Access Control Reader, Access Control Reader, Control Reader

References

• User Manual