Havit Lighting HV9101-2830B LED Strip Touch Panel Controller
Specifications
- Output Signal: RF signal
- Power Supply: DC Version – 12-24VDC, AC Version – 100-240VAC
- Power consumption: DC Version – < 20 mA, AC Version – < 15 mA
- Operating temperature: Not specified
- Relative humidity: Not specified
- Dimensions: DC Version – 19.4 mm x 43.58 mm x 83.00 mm, AC Version – 65.58 mm
Product Usage Instructions
Installation
- Do wiring the wall panel & RF receiver according to the wiring diagram.
- Power on the device.
- Touch the button to turn on the controller; the indicator should turn blue.
Pairing with RF Receiver
- Press the Learning Key button on the RF receiver or re-power the receiver three times continuously to set it into pairing status.
- Choose and click a zone number (e.g., zone 3).
- Touch the slider; LED lights connected with the RF receiver should flicker once, indicating successful pairing with zone.
Saving Color/Scene/Mode
- Choose and click one or multiple paired zone numbers (e.g., zone 1).
- Touch the slider to select the desired scene.
- Press and hold any scene buttons (e.g., S1); LED lights connected with the RF receiver should flicker once, confirming successful saving of color/scene.
Recalling Saved Colors/Scenes
- Choose and click one or multiple paired zone numbers (e.g., zone 1).
- Click any scene buttons (e.g., S1) to recall the saved scene.
Important: Read All Instructions Prior to Installation
FEATURES
DIMENSION
Product Data
| Output Signal | DC Version
RF signal |
AC Version
RF signal |
| Power Supply | 12-24VDC | 100-240VAC |
| Power consumption | < 20 mA | < 15 mA |
| Operating temperature | 0-40°C | 0-40°C |
| Relative humidity | 8% to 80% | 8% to 80% |
| Dimensions | 75x120x29.1mm | 75x120x29.1mm |
- Touch sensitive
- Glass interface(white & black)
- Compatible with all universal series RF receivers, radio frequency: 916.5MHz
- Control CCT color
- Control 4 zones synchronously and separately
- Waterproof grade: IP20
Safety & Warnings
- DO NOT install with power applied to device.
- DO NOT expose the device to moisture
Wiring diagram
Operation
- Do wiring the wall panel & RF receiver according to wiring diagram (please refer to the instruction of RF receiver that you would like to pair with)
- Power on, then touch the POWER button to turn on the controller, indicator of the controller turned blue
Pair with RF receiver
- Step 1:Click the “Learning Key” button on RF receiver or re-power on the receiver three times continuously to set it into pairing status
- Step 2:Choose and click a zone number(e.g. zone 3)
- Step 3:Touch the slider, LED lights connected with the RF receiver flicker once means the receiver is paired with zone 4 successfully.
Save color/scene/mode
- Step 1:Choose and click one or multiple paired zone numbers(e.g. zone 1)
- Step 2:Touch the slider to select the scene you like
- Step 3:Press and hold any scene buttons of S1/S2(e.g. S1) , LED lights connected with the RF receiver flicker once means the color/scene was saved successfully.
Recall the saved colors/scenes
- Step 1:Choose and click one or multiple paired zone numbers(e.g. zone 1)
- Step 2:Click any scene buttons of S1/S2(e.g. S1) to recall the saved scene
Installation
FAQ
Q: How do I switch between dual color control and brightness control?
A: Click on the dual color & brightness slider to switch between the two modes.
Q: How do I turn on/off a specific zone?
A: Press and hold down to turn on/off the corresponding zone after choosing it by clicking on the zone number.
Documents / Resources
 |
Havit Lighting HV9101-2830B LED Strip Touch Panel Controller [pdf] Installation Guide HV9101-2830B, 70010077, HV9101-2830B LED Strip Touch Panel Controller, HV9101-2830B, LED Strip Touch Panel Controller, Touch Panel Controller, Panel Controller, Controller |