XP Power NLB Mara Warewa Shirye-shiryen Analog Programming Interface don PLC

Bayanin samfur

Ƙayyadaddun bayanai

• Sunan samfur: Analog Programming Interface don PLC
• Shafin: 9.7
• Mai ƙera: XP Power FuG
• Wuri: Am Eschengrund 11, D-83135 Schechen, Jamus

Umarnin Amfani da samfur

Analog Programming Option / Interface

Gabaɗaya

Ana amfani da ƙa'idar analog (15-pole Sub-D soket akan sashin baya) don sarrafa voltage saitin, saitin yanzu, FITARWA ON/KASHE, da ayyuka na musamman dangane da nau'in naúrar. Ana ba da ƙimar gaske azaman analog voltages yayin da hanyoyin sarrafawa sigina na dijital ne. The dubawa yana samuwa a kan raya panel na DC samar da wutar lantarki.

Aiki: Voltage da ƙimar halin yanzu ana iya saita su ta amfani da siginar analog na al'ada. Maganar ciki voltagAna iya samun dama ga e +10V a fil 10 don samar da siginar saiti.

Sigina da Kebul na Sarrafa: Alamar analog tana amfani da soket na Sub-D mai kariya. An haɗa garkuwa da yuwuwar gidaje (PE). Tabbatar da kariya mai kyau da ƙasa don dacewa da dacewa da lantarki (EMC).

Voltage Iyakance: Voltage iyakance saita ta potentiometer VLIMIT a gaban panel ya ci gaba da aiki. Halayen na'ura kamar daidaito da kwanciyar hankali ba su da tasiri saboda haɗakar siginar kai tsaye.

Gargadi: Raka'a tare da zaɓin shirye-shiryen analog ɗin da ba keɓantacce ba dole ne a yi amfani da shi kyauta mai yuwuwa don hana rauni na mutum da lalacewar dukiya.

Abubuwan da ba za a iya gani ba yayin amfani da shirye-shiryen Analog

Hadari: Janye kebul na haɗin shirye-shiryen analog a yanayin ANALOG na iya haifar da fitarwa voltage zuwa 0V. Sake haɗa kebul ɗin ba tare da canza saituna ba zai fitar da ƙimar saiti na ƙarshe.

Tambayoyin da ake yawan yi

Tambaya: Zan iya amfani da haɗin haɗin analog don kowane nau'in na'urori?

A: Aikin fil na iya bambanta dangane da jerin na'urar. Koma zuwa kanview don shirye-shiryen analog a cikin jagorar don takamaiman bayani.

Tambaya: Menene madaidaicin izinin izinin kebul na kariya don ƙirar analog?

A: Matsakaicin tsayin da aka halatta shine 3m don tabbatar da biyan buƙatun dacewa na lantarki (EMC).

Interface zuwa umarnin aiki
(An Fassara daga Jamusanci)
Shafin: 9.7

An ƙirƙira wannan littafin ta: XP Power FuG, Am Eschengrund 11, D-83135 Schechen, Jamus

Analog Programming zaɓi / dubawa

Gabaɗaya
Ana amfani da ƙa'idar analog (15-pole Sub-D soket akan sashin baya) don sarrafa ayyukan voltage saitin, saitin yanzu haka da FITAR ON/KASHE da ayyuka na musamman, dangane da nau'in naúrar. Ana ba da ainihin ƙimar halin yanzu azaman analog voltages da sabbin hanyoyin sarrafawa azaman sigina na dijital.
Ayyukan wasu fil sun bambanta dangane da jerin na'urar. Da fatan za a koma ga overview don shirye-shiryen analog a ƙarƙashin 1.3.

The dubawa yana samuwa a kan raya panel na DC samar da wutar lantarki.

Aiki
Voltage da ƙimar halin yanzu za a iya saita su tare da siginonin analog na al'ada (nazarin waje). Maganar ciki voltagAna iya buga e +10 V a fil 10 kuma a yi amfani da su don samar da waɗannan sigina na saiti (misali tare da 10 Kg potentiometers), duba zaɓuɓɓukan wayoyi a ƙarƙashin 1.

Sigina da kebul na sarrafawa
Ana aiwatar da mu'amalar analog ta hanyar soket na Sub-D mai kariya. An haɗa garkuwa da yuwuwar gidaje (PE). Mai haɗa mating, da kuma hanyar haɗin bayanai, dole ne a kiyaye shi kuma dole ne a haɗa garkuwar da juna. Matsakaicin izinin izinin kebul ɗin kariya shine 3m. Waɗannan buƙatun ne don bin ka'idodin daidaitawa na lantarki (EMC), duba kuma Sanarwa na Daidaitawa a cikin kari.

Voltage iyaka
Voltage iyakance, idan akwai daidaitacce ta potentiometer VLIMIT a gaban panel na DC wutar lantarki, har yanzu yana aiki.

Saboda haɗakar siginar analog kai tsaye, halayen na'urar kamar daidaito, layi, kwanciyar hankali da ƙimar zafin jiki ba su canzawa.

GARGADI
Lura cewa raka'o'in samar da wutar lantarki waɗanda ke sanye da zaɓin shirye-shiryen analog ɗin da ba keɓantacce ba ba za a iya sarrafa su kyauta ba!

Wannan haɗin gwiwa mai yuwuwa yana ba da kariya daga raunin mutum da lalacewar dukiya.
Don dalilai na aminci ana isar da sandar fitarwa guda ɗaya dangane da nau'in na'urar.

Nau'ukan of na'urori
HCB	HCK	HCP	MCA	MCP	NLB	NLN	NTN
"0V" mai girma			"-" ko "A-" a kasa		"A0" ƙasa	"+" ƙasa	"A+" ƙasa

Amfani da rashin kuskure lokacin amfani da shirye-shiryen analog

GARGADI

Hatsarin girgiza wutar lantarki a fitinun wutar lantarki!

Idan na'urar tana aiki a yanayin ANALOG kuma an ja kebul ɗin shirye-shirye na analog, fitarwa voltage yana saukowa zuwa 0V bayan lokacin saukewa wanda ya dogara da nauyin haɗi. Da zarar an sake kunna kebul na shirye-shirye na analog ba tare da canza saitunan sarrafawa ba, saiti na ƙarshe zai kasance a wurin abubuwan da aka fitar.

Ƙarsheview Analog Programming

Pin	Bayani	Nau'in	Aiki
1	CC	DO	kayayyaki kimanin. + 24 V idan wutar lantarki tana cikin yanayin halin yanzu koyaushe. Daidai da LED CC, Ri kusan. 2.7 ku
2	CV	DO	Kayayyakin kusan + 24V idan wutar lantarki ta kasance a koyaushetage yanayin. Daidai da LED CV, Ri kusan. 2.7 ku
3	I-MON	AO	siginar saka idanu na ainihin fitarwa na yanzu 0…+10 V yana wakiltar 0… na halin yanzu
4	VPS	AO	Slider Voltage tukunya a gaban panel 0…+10 V, Ri kusan. 10 ku
5	Ba a yi amfani da shi ba		Don na'urorin da Hanyoyin ciniki na HCB ba tare da aiki ba.
	IPS	AO	Slider Voltage tukunya a gaban panel 0…+10 V, Ri kusan. 10 ku
6	FITOWA TA	DI	Fitar ON +24V
7	Ba a yi amfani da shi ba		don na'urorin da HCB, MCA, MCP, NLN, NTN jerin ba tare da aiki ba.
	POL-SET	DI	shigarwar sarrafawa don juyawa juzu'i na polarity na lantarki (Zaɓi) POS = fil (7) buɗe, NEG = an haɗa zuwa Fin (6) 0VD
	V/I REG	DI	sauyawa voltagTsarin e/na yanzu yana aiki ne kawai ga tsarin NLB jerin Yanayin V-REG: haɗa Pin7 tare da Pin6 (Pin7=0), Yanayin I-REG: Pin7 ba a haɗa shi ba
8	V-SET	AI	0…+10 V yayi daidai 0…Ba a sani ba, juriyar shigarwa zuwa 0V kusan. 10 MΩ
9	0V	A-GND	ƙasa don siginar analog, dole ne kada ya ɗauki kowane halin yanzu
10	+10VREF	AO	+10V Magana (fitarwa), max. 2 mA
11	V-MON	AO	ainihin fitarwa voltage siginar saka idanu 0…10 V yana wakiltar 0…Ba a sani ba; Ri kusan. 100 Ω
12	Saukewa: 0VD	DI	0V (24V0) da 0 V ta zaɓi juzu'i na juyawa
13	Ba a yi amfani da shi ba		don na'urorin da Farashin MCP ba tare da aiki ba
	POL- Matsayi	DO	Matsayin polarity (zaɓi) ya shafi na'urori masu juyar da polarity. POS polarity = kusan. + 24 V, NEG polarity = 0 V Ri kusan. 2.7 ku
	-10V REF	AO	ga na'urorin da HCB, jerin NLB
	P-LIM	DO	isar da kusan. + 15 V, lokacin da yanayin zafi Farashin MCA na'urar tana kora zuwa iyakar wuta, daidai da LED P-LIM a gaban panel
	S-REG	DO	Isar da kusan + 15 V, idan NTN, NLN jerin na'urar a cikin sarrafa SENSE (kawai tare da aiki aikin firikwensin), daidai da LED S-ERR a gaban panel.
14	+24V	DI	+ 24V daga PLC
15	Ba a yi amfani da shi ba		don na'urorin da Hanyoyin ciniki na HCB
	I-SET	AI	0…+10 V daidai yake da 0…Inominal, juriya na shigarwa akan 0 V kusan. 10 MΩ
Duk darajar voltages da igiyoyin ruwa suna cikin DC. D=Digital, A=Analog, I=Input, O=Fitowa Kula da nau'in naúrar ku da zaɓuɓɓuka a cikin layin launi.

Zaɓuɓɓukan wayoyi

Aiki na analog interface

GARGADI

Kunna/kashe FITARWA
Ana kunna DC OUPUT ta fil 12 da fil 6, duba 1.3
Idan DC OUTPUT aka kunna tare da 24V tsakanin fil 6 da fil 12, OUTPUT ya ci gaba da aiki har zuwa vol.tage tsakanin fil 6 da fil 12 ko mains an kunna oV.
A halin da ake ciki na mains voltage gazawar, DC OUTPUT ya kasance a kunne. Da zaran mains voltage an sake ba da shi, DC OUTPUT yana aiki kuma!

Mai yuwuwar girgiza wutar lantarki saboda saura voltage a fitarwa!
Lokacin da naúrar aka kunna oV ko a yayin da rashin wutar lantarki, saura voltage / halin yanzu ba zai kasance ba
nunawa akan abubuwan saka idanu!
Kula da lokacin fitarwa!

Sanya zaɓin shirye-shiryen analog / dubawa cikin aiki

1. Dole ne a aiwatar da shigarwar ƙirar analog lokacin da wutar lantarki ta DC ba ta aiki!
2. Za a haɗa haɗin haɗin na'ura mai sarrafawa zuwa haɗin wutar lantarki na DC kamar yadda aka ƙayyade.
3. Yanzu kunna POWER switch (1).
4. Zaɓi yanayin aiki na ANALOG tare da maɓalli ko masu juyawa. LED ANALOG yanzu yana haskakawa.
   Yanzu ana sarrafa na'urar a waje ta soket ɗin shirye-shirye!

Don kunna wutar lantarki, ci gaba kamar haka:

1. Saita ƙimar a fil (8) V-SET da fil (15) I-SET zuwa 0 V.
2. Canja oV na aiki voltage tsakanin Pin 6 da 12.
3. Bayan fitarwa voltage ya kai darajar <50V, canza na'urar gaba daya oV ta amfani da

Canjin WUTA.
Ana kunna wutar lantarki ta DC oV.

KARFIN DUNIYA MTSARI

Takardu / Albarkatu

XP Power NLB Mara Warewa Shirye-shiryen Analog Programming Interface don PLC [pdf] Jagoran Jagora Matsakaicin Tsare-tsare na Analog na PLC, NLB, Interface Programming Interface don PLC

Magana

• Manual mai amfani