M5 STACK Flow Connect Software 

BAYANI

Haɗin Flow haɗe-haɗe ne mai sarrafa masana'antu wanda aka ƙera don haɗaɗɗun yanayin aiki da kai da yanayin sadarwa. Yana fasalta ESP32-S3R8 microcontroller a cikin ainihin sa, sanye take da dual-core Xtensa LX7 processor wanda ke gudana har zuwa 240MHz, kuma ya haɗa da 8MB PSRAM da 16MB FLASH ƙwaƙwalwar ajiya, mai iya ɗaukar babban aiki na lissafi da buƙatun multitasking. Don ajiya, yana amfani da 128Mbit (16MB) 3.3V NOR flash, yana tabbatar da dogon lokaci, barga aiki don firmware, bayanai, da daidaitawa. file ajiya.
Mai sarrafawa yana goyan bayan ka'idojin sadarwa da yawa, gami da bas ɗin CAN dual, RS232, RS485, da musaya na TTL, yana mai da shi dacewa da kewayon masana'antu da aikace-aikacen IoT. Don haɓaka hulɗar mai amfani, Flow Connect yana haɗa Neopixel RGB LED sarrafa hasken wuta, yana ba da damar launi mai ƙarfi da tasirin haske don ra'ayin gani na gani.
Bugu da kari, tsarin sarrafa wutar lantarki na Flow Connect yana amfani da masu juyawa DC-DC da yawa waɗanda ke goyan bayan voltage fitarwa daga 12V zuwa 3.3V. Hakanan yana fasalta ginannun fis ɗin lantarki (eFuse) don kare kowane voltage tashar daga overcurrent, tabbatar da aiki lafiya ko da a cikin mummuna yanayi.
An tsara Haɗin Flow tare da buƙatun buƙatun sarrafa masana'antu, sufuri mai hankali, da aikace-aikacen ƙofa na IoT a zuciya, yana ba da ingantacciyar hanyar sadarwa ta multiprotocol, ma'ajin bayanai mai ƙarfi, nunin RGB mai ƙarfi, da cikakkiyar kariyar wuta.

Haɗin Yaɗawa

1. Iyawar Sadarwa:
   • Babban Mai Kula: ESP32-S3R8
   • Sadarwar Mara waya: Wi-Fi (2.4 GHz), Ƙarfin Ƙarfin Bluetooth (BLE) 5.0
   • Dual CAN Bus: Yana goyan bayan hanyoyin haɗin bas na CAN guda biyu don ingantaccen sadarwar bayanai a cikin mahallin masana'antu.
   • Sadarwar Serial: RS232, RS485, da TTL musaya don zaɓuɓɓukan sadarwa iri-iri.
2. Processor da Ayyuka:
   • Samfurin sarrafawa: Xtensa LX7 Dual-core (ESP32-S3R8)
   • Ma'ajiyar Ajiya: 16MB Flash, 8MB PSRAM
   • Mitar Mai sarrafawa: Xtensa® dual-core 32-bit LX7 microprocessor, har zuwa 240 MHz
3. Nunawa da Shigarwa:
   • RGB LED: Haɗin Neopixel RGB LED don ra'ayin gani mai ƙarfi.
4. Ƙwaƙwalwar ajiya:
   • NO Flash: 128Mbit (16MB), 3.3V don firmware da ajiyar bayanai.
5. Gudanar da Wuta:
   • Samar da Wutar Lantarki: Masu juyawa DC-DC masu goyan bayan fitowar 12V zuwa 3.3V.
   • Kariya: Ginin fis ɗin lantarki (eFuse) don kariyar wuce gona da iri a duk voltage tashoshi.
6. Fil na GPIO da Matsalolin Tsare-tsare:
   1. Grove Interface: Yana goyan bayan haɗi da haɓaka na'urori masu auna firikwensin I2C da sauran kayayyaki.
7. Wasu:
   • Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwaƙwalwa na Ƙaƙwalwa na C don shirye-shirye, wutar lantarki, da sadarwar serial.
   • Girman Jiki: 60*60*15 mm

BAYANI

Siga da ƙayyadaddun bayanai	Daraja
MCU	ESP32-S3R8@ Xtensa dual – core 32-bit LX7, 240MHz
Iyawar Sadarwa	Wi-Fi, BLE, Dual CAN Bus, RS232, RS485, TTL
Ƙara Voltage	12V zuwa 3V DC (ta hanyar masu juyawa DC-DC)
Ƙarfin Ma'ajiya ta Flash	16MB Flash
Ƙarfin Ma'ajiya na PSRAM	8MB PSRAM
KO Flash	GD25Q128/ W25Q128, 128 Mbi t (16MB), 3. 3V
LED RGB	6 x Neopixel RGB LEDs don haske mai ƙarfi
Hanyoyin Fadada	Grove interface don haɗawa da faɗaɗa firikwensin I2C
Yanayin Aiki	0 ° C - 40 ° C
Wi-Fi Mitar Aiki	802. lb/ g/ n: 2412 MHz – 2482 MHz
Mitar Aiki BLE	2402 MHz - 2480 MHz
Mai ƙira	Abubuwan da aka bayar na M5Stack Technology Co., Ltd

SAURAN FARA

Kafin kayi wannan matakin, duba rubutun a shafi na ƙarshe: Sanya Arduino

Buga bayanan WiFi

1. Bude Arduino IDE (Duba zuwa
   https://docs.m5stack.com/en/arduino/arduino_ide don jagorar shigarwa don hukumar haɓakawa da software)
2. Zaɓi allon ESP32S3 DEV Module da tashar tashar da ta dace, sannan loda lambar
3. Bude serial Monitor don nuna Wi-Fi da aka bincika da bayanin ƙarfin sigina
   
   

Buga bayanan BLE

1. Bude Arduino IDE (Duba zuwa
   https://docs.m5stack.com/en/arduino/arduino_ide don jagorar shigarwa don hukumar haɓakawa da software)
2. Zaɓi allon ESP32S3 DEV Module da tashar tashar da ta dace, sannan loda lambar
3. Bude serial Monitor don nuna BLE da aka bincika da kuma bayanan ƙarfin sigina
   
   

Gargadi na FCC

FCC Tsanaki: 

Duk wani canje-canje ko gyare-gyaren da ƙungiyar da ke da alhakin bin doka ba ta amince da su ba na iya ɓata ikon mai amfani na sarrafa kayan aiki.
Wannan na'urar ta bi sashe na 15 na Dokokin FCC. Aikin yana ƙarƙashin sharuɗɗa biyu masu zuwa:

1. Wannan na'urar bazai haifar da tsangwama mai cutarwa ba, kuma
2. dole ne wannan na'urar ta karɓi duk wani tsangwama da aka samu, gami da tsangwama wanda zai iya haifar da aiki maras so.

MUHIMMAN NOTE:

Lura: An gwada wannan kayan aikin kuma an same shi don biyan iyaka don na'urar dijital ta Class B, bisa ga sashi na 15 na Dokokin FCC. An tsara waɗannan iyakokin don ba da kariya mai ma'ana daga kutsawa mai cutarwa a cikin shigarwar mazaunin.
Wannan kayan aiki yana haifarwa, yana amfani da kuma zai iya haskaka ƙarfin mitar rediyo kuma, idan ba'a shigar da shi ba kuma akayi amfani dashi daidai da umarnin, yana iya haifar da tsangwama mai cutarwa ga sadarwar rediyo. Duk da haka, babu tabbacin cewa tsangwama ba zai faru a cikin wani shigarwa na musamman ba. Idan wannan kayan aikin ya haifar da tsangwama mai cutarwa ga liyafar rediyo ko talabijin, wanda za'a iya tantancewa ta hanyar kashe kayan aiki da kunnawa, ana ƙarfafa mai amfani da yayi ƙoƙarin gyara tsangwama ta hanyar ɗaya ko fiye na waɗannan matakan:

• Sake daidaitawa ko matsar da eriya mai karɓa.
• Ƙara rabuwa tsakanin kayan aiki da mai karɓa.
• Haɗa kayan aiki zuwa wani mashigar da ke kewaye daban da wanda aka haɗa mai karɓa zuwa gare shi.
• Tuntuɓi dila ko gogaggen masanin rediyo/TV don taimako.

Wannan kayan aikin ya dace da iyakokin fiddawa na FCC da aka tsara don yanayin da ba a sarrafa shi ba. Ya kamata a shigar da wannan kayan aikin tare da mafi ƙarancin nisa 20cm tsakanin radiyo & jikin ku.

Arduino Shigar

• Shigar da Arduino IDE(https://www.arduino.cc/en/Main/Software) Danna don ziyartar jami'in Arduino website , kuma zaɓi kunshin shigarwa don tsarin aikin ku don saukewa.
• Shigar da Gudanarwar Hukumar Arduino

1. Manajan Hukumar URL ana amfani da shi don lissafta bayanan hukumar haɓaka don takamaiman dandamali. A cikin Arduino IDE menu, zaɓi File -> Abubuwan da ake so
   
2. Kwafi gudanarwar hukumar ESP URL kasa cikin Ƙarin Hukumar Gudanarwa URLs: filin, kuma ajiye.
   https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
   
   
3. A cikin labarun gefe, zaɓi Manajan allo, bincika M5Stack, sannan danna Shigar.
   
4. A cikin labarun gefe, zaɓi Manajan allo, bincika M5Stack, sannan danna Shigar.
   Dangane da samfurin da aka yi amfani da shi, zaɓi allon haɓaka daidai a ƙarƙashin Kayan aiki -> Board -> M5Stack -> {ESP32S3 DEV Module Board}.
   
5. Haɗa na'urar zuwa kwamfutarka tare da kebul na bayanai don loda shirin

Takardu / Albarkatu

M5 STACK Flow Connect Software [pdf] Jagorar mai amfani M5FCV1, 2AN3WM5FCV1, Flow Connect Software, Haɗa Software, Software

Magana

• Manual mai amfani